Facile preparation and strong adhesive strength of honeycomb polyurethane films with small pore diameter

With the continuous development of bionics, such as, geckos and virginia creeper with both superhydrophobic and super-adhesive, the surface wetting and super-adhesive properties of various porous materials have attracted extensive attention of the scientific and medical communities. Here, the honeycomb polyurethane (PU) porous films with strong adhesion were successfully prepared by microphase separation method and the effects of growth parameters on their microstructure and adhesive strength to ice were investigated. It was found that a high relative humidity (e.g., 100%) and a low solution concentration (e.g., 2%) facilitated the formation of ordered honeycomb PU porous films, and as-prepared PU pores with average pore diameter as small as 5 μm are better ordered and more uniform than these in related documents. Although the contact angle of water droplets on the surface of PU porous films increased from the premodification value of 85–130° to more than 160° after surface modification with polydopamine (PDA), the corresponding rolling angle remained approximately constant (180°), indicating that the surface of PU porous films has strong adhesion similar to geckos and virginia creeper. Furthermore, at lower temperature, the PU porous films exhibited the high adhesive strength of 142.13 kPa on ice, which was strongly dependent on the porous microstructures and surface compositions. The improved adhesive behavior to ice of honeycomb PU porous films modified with PDA provides new strategies for surface modification of materials and potential applications in medical domain.     

Mathematical Modeling of Drying Processes of Selected Fruits and Vegetables

This study investigates the behavior of fruit and vegetable samples during drying. The experimental data are fitted to several different thin-layer drying models. Regression analysis is used to determine model parameters, while statistical indicators serve to evaluate the goodness of fit. The power function model gives the best fit for all examined samples. Based on this model, different drying and heat storage technologies can be combined to ensure that the required residual moisture content of an agricultural product is reached. It is demonstrated on the case of a specific Togolese processing plant that under favorable conditions, fossil fuel consumption can be decreased by 33 %.     

建筑工业化发展的多群体演化博弈与仿真研究

新型建筑工业化具有高质量、低消耗、可循环发展等特征，其推广已上升到国家战略层面。利用演化博弈方法，建立“政府-开发商-银行” 的三方动态演化博弈模型，进行各博弈主体策略的演化稳定性分析，并针对初始状态、奖惩力度、借贷风险和开发成本等对演化结果的影响进行动态仿真。在此基础上， 考虑开发商群体的网络拓扑特征对演化真实性的影响，引入复杂网络理论， 以无标度网络为载体描述开发商个体的连接偏好和决策机制，构建政府监管下的建筑工业化扩散模型，并通过仿真深入研究相关因素对扩散深度的影响作用，最后结合仿真结果给出相应对策建议。     

"7·15"洪灾的反思及防洪救灾对策

4号强热带风暴“碧利斯”造成突如其来的特大暴雨,降雨范围广,强度大,总量多,时间长,在宜章创下了之最,而且在湖南省也是罕见的。文章对“7·15”特大洪灾雨水情、灾情、抢险救灾存在的问题进行了分析和反思,并提出了防汛抢险的措施和对策。     

一种可替代漂珠的低密度材料

漂珠低密度水泥浆由于密度低、强度高、体系稳定而在油田低压易漏层及低压油气层长封固段固井作业中获得了广泛的应用。但近年来,由于漂珠的产量越来越少,油田低成本要求急需开发代替漂珠的新型减轻材料,以满足配制低密度水泥浆的需求。开发了BCL-10S低密度混合减轻材料,其物化性能与漂珠相当,用它作减轻剂配制的低密度水泥浆性能与用漂珠作减轻剂配制的低密度水泥浆性能相媲美,并已经在长庆油田获得了应用。     

国产风机盘管空调系统常见问题分析

分析了国产风机盘管使用中常见的问题,指出机组因风量不足、冷量风量匹配不合理以及风机盘管某些设备故障,导致了风机盘管精度低、舒适性差、能耗高等一系列问题。指出应引起空调设计和运行维护人员的注意。     

Flash器件中氧化硅/氮化硅/氧化硅的特性

对普遍采用的氧化硅/氮化硅/氧化硅( ONO)三层复合结构介质层的制备工艺及特性进行了研究分析,研究了ONO的漏电特性以及顶氧( top oxide)和底氧( bottom oxide)的厚度对ONO层漏电的影响.结果表明,采用较薄的底氧和较厚的顶氧,既能保证较高的临界电场强度,又能获得较薄的等效氧化层厚度,提高耦合率,降低编程电压.     

多功能杀菌剂的合成及其性能研究

在现有季铵盐类杀菌灭藻剂上增加一个脂键，连接一个有机酸基团，合成一种兼具阻垢缓蚀功能的新型工业水处理用杀菌灭藻剂(多功能杀菌剂)，经一系列评价实验表明：新型杀菌剂是较理想的杀菌剂，在较低浓度下，对硫酸盐还原菌(SRB)及腐生菌(TGB)均有很好的杀灭效果，优于1227杀菌剂，同时还具有较好的缓蚀阻垢效果。     

机载行波管发射机设计的基本原则

论述了机载行波管发射机设计中需要遵循的5个基本原则，强调了行波管使用以及环境适应的重要性及优先地位，提出了对发射机指标理解的认识，以及最简设计与交叉设计的建议；介绍了机载行波管发射机设计过程中的几个主要步骤，对发射机主要性能参数进行了简单的分类与分析，并给出了一个行波管发射机设计的示例。