柔性纤维结构超级电容器研究进展

为了提高电源器件与人体高曲率表面的适配性，电源器件突破平板结构的限制，衍生出了柔性纤维结构。柔性纤维超级电容器具有高功率密度、超长循环寿命和柔性舒适等特点有望成为最具前景的柔性可穿戴电源之一。因此，本文主要介绍了碳材料、过渡金属氧化物以及复合材料三种功能材料对柔性纤维超级电容器结构和性能的影响。每种材料凭借自身独特的性质在柔性纤维超级电容器器件中发挥着重要作用，并助力可穿戴电源器件的发展。     

VO2/GaAs异质结的制备及其光电特性研究

采用直流磁控溅射和后退火氧化工艺在p型GaAs单晶衬底上成功制备了n-VO_2/pGaAs异质结,研究了不同退火温度和退火时间对VO_2/GaAs异质结性能的影响,并分析其结晶取向、化学组分、膜层质量以及光电特性。结果表明,在退火时间2 h和退火温度693 K下能得到相变性能最佳的VO_2薄膜,相变前后电阻变化约2个数量级。VO_2/GaAs异质结在308 K、318 K和328 K温度下具有较好的整流特性,对应温度下的阈值跳变电压分别为6.9 V、6.6 V和6.2 V,该结果为基于VO_2相变特性的异质结光电器件的设计与应用提供了可行性。     

Comparison of yield and metabolites according to the types of hilling materials utilized during Glehnia littoralis sprout vegetable cultivation

Food Science and Biotechnology - Various hilling materials (rice hulls, pine sawdust, and perlite) were compared to produce sprout vegetables using beach silvertop (Glehnia littoralis Fr. Schm. ex...     

基于全U网络的混凝土路面裂缝检测算法

针对现有的混凝土裂缝检测算法在各种复杂环境中检测精度不够、鲁棒性不强的问题,根据深度学习理论和U-net模型,提出一种全U型网络的裂缝检测算法。首先,依照原U-net模型路线构建网络;然后,在每个池化层后都进行一次上采样,恢复其在池化层之前的特征图规格,并将其与池化之前的卷积层进行融合,将融合之后的特征图作为新的融合层与原U-net网络上采样之后的网络层进行融合;最后,为了验证算法的有效性,在测试集中进行实验。结果表明,所提算法的平均精确率可达到83.48%,召回率为85.08%,F1为84.11%,相较于原U-net分别提升了1.48%,4.68%和3.29%,在复杂环境中也能提取完整裂缝,保证了裂缝检测的鲁棒性。     

Optical design of the Lyman alpha based beam emission spectroscopy(LAB)diagnostic on the HL-2A tokamak

In this article, we present the optical design of a novel diagnostic on the HL-2 A tokamak, i.e. the20-channel edge Lyman-alpha beam emission spectroscopy, which is a promising solution for edge density turbulence research on tokamaks, as it offers the possibility of density fluctuation measurement with a 3.3 mm spatial resolution while maintains a high temporal resolution of1 μs. The optical path, including the reflective collection optics, the high-dispersion spectrometer, and the linear detector array, is carefully optimized to obtain a good image quality and a high throughput. The maximum root mean square radius of the collection optics is 64 μm.The detected photon flux is estimated to be about 10~(11) photons/s/channel.     

Pressure-induced transparency of MgO,Al2O3, AlN,and cBN ceramics at room temperature

The in situ axial X-ray diffraction patterns of four ceramic powder samples (MgO, Al₂O₃, AlN, and cBN) that were compressed in a diamond anvil cell under uniaxial non-hydrostatic conditions were recorded. The microscopic deviatoric stress as a function of the pressure was determined from the X-ray diffraction peak broadening analysis: the curves increased approximately linearly with the pressure at the initial compression stage and then levelled off under further compression. Pressure-induced transparency was observed in all of the samples under compression, and the pressure at the turning point on the curves of the microscopic deviatoric stress versus pressure corresponded to the pressure at which the samples became transparent. Analysis of the microstructural features of the pressure-induced transparent samples indicated that the compression caused the grains to fracture, and the broken grains bonded with each other. We demonstrated that the ceramics’ pressure-induced transparency was a process during which the grains were squeezed and broken, the pores were close between the grains, and the broken grains were re-bonded under compression.     

Rheological phase reaction synthesis and electrochemical performance of LiFe2/3Mn1/3PO4/C cathode for lithium-ion batteries

LiFe_2/3Mn_1/3PO₄/C composite was prepared by the rheological phase reaction using LiH₂PO₄, Li₂CO₃, FePO₄, Mn(Ac)₂·4H₂O and ascorbic acid as starting materials. The crystal structure and morphology of as-synthesized sample were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The analysis of XRD results showed that the obtained sample was single-phase with orthorhombic olivine-type structure (Pnma space group). SEM micrographs revealed that the sample was aggregates, with an irregular morphology. The initial discharge capacity was 166.9, 149.1, 139.6, 112.8, 82.93 mAh g^??1 at the rate of 0.1, 0.5, 1, 2, and 10 C, respectively. And when the rate was 0.1, 0.5, 1, 2, and 10 C, the capacity retention was 92.2%, 90%, 92.9%, 97.6%, 91.5% after 50, 100, 200, 200, 500 cycles, respectively.

     

基于SRAM的通用存算一体架构平台在物联网中的应用

最近,存算一体(IMC)架构引起了广泛关注,并被认为有望成为突破冯诺依曼瓶颈的新型计算机架构,特别是在数据密集型(data-intensive)计算中能够带来显著的性能和功耗优势.其中,基于SRAM的IMC架构方案也被大量研究与应用.该文在一款基于SRAM的通用存算一体架构平台——DM-IMCA的基础上,探索IMC架构在物联网领域中的应用价值.具体来说,该文选取了物联网中包括信息安全、二值神经网络和图像处理在内的多个轻量级数据密集型应用,对算法进行分析或拆分,并将关键算法映射到DM-IMCA中的SRAM中,以达到加速应用计算的目的.实验结果显示,与基于传统冯诺依曼架构的基准系统相比,利用DM-IMCA来实现物联网中的轻量级计算密集型应用,可获得高达24倍的计算加速比.     

基于电机效率的纯电动汽车传动系统参数匹配研究

为降低能耗、提高续航里程,本文提出了以提高电机效率为目标的纯电动汽车三档变速传动方案.首先,在分析电机工作特性的基础上提出了三档传动系统参数匹配方法;然后以某纯电动汽车为研究对象,对其驱动系统进行了改动:方案一在不改变原车型动力系统参数的情况下将传动系统由一档改为三档,并运用所提出的方法确定各档位的传动比;方案二在满足整车动力性指标要求下对电机重新选型并匹配三档传动系统;最后利用ADVISOR软件进行NEDC工况仿真分析.结果表明:在不改变原车型动力系统参数的情况下,采用三档传动可使整车的动力性和经济性都有一定的提升,续航里程提高了 9.2％,百公里电耗降低了 1.28 kW·h;重新选型电机后,采用三档传动续航里程提高了 14.1％,百公里电耗降低了 1.87kW·h.