Group Decision Making by Using Incomplete Fuzzy Preference Relations Based on T‐Consistency and the Order Consistency

The existing group decision making techniques may not satisfy the order consistency for aggregation in some cases. The algorithm proposed in this paper overcomes the weaknesses of the existing techniques. The method determines the unknown preferences for group decision making in such a manner that the resulting matrix is T‐consistent and order consistent simultaneously.     

Effects of molybdenum additions on the structure, depth, and austenite grain size of the case of carburized 0.13% carbon steels

Carbon (0.13%) steel samples containing about 0.48% molybdenum (Mo) singly and in combination with nickel (Ni) were carburized in a natural Titas gas atmosphere at a temperature of 1223 K (950 °C) and at a pressure of about 0.10 MPa (15 psia) for time periods ranging from 1–4 h followed by slow cooling in the furnace. Their microstructure was studied by optical microscopy. The austenite grain size of the case and the case depths were determined. It was found that Mo and Ni alone and in combination decrease the thickness of the cementite network near the surface of the carburized case of the steels. However, Ni is found to be more effective than Mo in decreasing the thickness of cementite network. Both Mo and Ni enhance the formation of Widmanstätten cementite plates at the grain boundary and within the grains near the surface of the carburized steels. However, Ni alone is more effective than Mo in the formation of Widmanstätten cementite plates. In the presence of Ni, Mo is much more effective in the formation of Widmanstätten cementite plates than Mo in absence of Ni. It was also revealed that both Mo and Ni increased the case depth. Ni is more effective than Mo in increasing the case depth. The combined effect of Mo and Ni is much greater than that of either Mo or Ni alone in increasing case depth. Mo as Mo carbide (Mo₂C) particles refined the austenite grain size of the carburized case. Ni in solution was not found to have any effect in restricting grain growth of austenite, but the presence of Ni enhances the austenite grain size refining effect of Mo in the carburized case.     

Mixed formulation of nonlinear beam on foundation elements

This paper presents an inelastic element for the analysis of beams on foundations. The element is derived from a two-field mixed formulation with independent approximation of forces and displacements. The state determination algorithm for the implementation of the element in a general purpose nonlinear finite element analysis program is presented and its stability characteristics are discussed. Numerical studies are performed to compare the model with the classical displacement formulation. The studies confirm the superiority of the proposed model in describing the inelastic behavior of beams on foundations.     

PERFORMANCE OF THREE STAGE TURBO－EQUALIZATION－DECODING

An increasing demand for high data rate transmission and protection over bandlimited channels with severe inter-symbol interference has resulted in a flurry of activity to improve channel equalization. In conjunction with equalization, channel coding-decoding can be employed to improve system performance. In this letter, the performance of the three stageturbo-equalization-decoding employing log maximum a posteriori probability is experimentally evaluated by a fading simulator. The BER is evaluated using various information sequence and interleaver sizes taking into account that the communication medium is a noisy inter symbol interference channel.     

A visual tool for computer supported learning: The robot motion planning example

We introduce an effective computer aided learning visual tool (CALVT) to teach graph-based applications. We present the robot motion planning problem as an example of such applications. The proposed tool can be used to simulate and/or further to implement practical systems in different areas of computer science such as graphics, computational geometry, robotics and networking. In the robot motion planning example, CALVT enables users to setup the working environment by creating obstacles and a robot of different shapes, specifying starting and goal positions, and setting other path or environment parameters from a user-friendly interface. The path planning system involves several phases. Each of these modules is complex and therefore we provide the possibility of visualizing graphically the output of each phase. Based on our experience, this tool has been an effective one in classroom teaching. It not only cuts down, significantly, on the instructor’s time and effort but also motivates senior/graduate students to pursue work in this specific area of research.     

Pad effects on material-removal rate in chemical-mechanical planarization

The role of a porous pad in controlling material-removal rate (MRR) during the chemical-mechanical planarization (CMP) process has been studied numerically. The numerical results are used to develop a phenomenological model that correlates the forces on each individual abrasive particle to the applied nominal pressure. The model provides a physical explanation for the experimentally observed domains of pressure-dependent MRR, where the pad deformation controls the load sharing between active-abrasive particles and direct pad-wafer contact. The predicted correlations between MRR and slurry characteristics, i.e., particle size and concentration, are in agreement with experimentally measured trends reported by Ouma¹ and Izumitani.²     

A study of neutron and gamma radiation effects on transmission of various types of glasses, optical coatings, cemented optics and fiber

A study of radiation effects on various types of glasses, dielectric optical coatings, cemented optics and fiber was undertaken with a view to select them for extreme radiation environments. Samples were exposed to different radiation doses in the Pakistan Research Reactor-I (PARR-I) for neutron and Cobalt 60 source for gamma irradiation. Transmissions were measured before and after irradiation. The dielectric coatings were subjected to additional tests (adhesion, abrasion and humidity, etc.) as per MIL-M-13508C and MIL-C-675C. All 15 glasses studied showed varying amounts of transmission loss as expected, with negligible degradation for three types. Recovery of transmissions with time/ageing was also studied, with more or less complete recovery with temperature annealing. A faster bleaching of darkened/brown glasses was achieved by using UV lamps or UV laser. The dielectric coatings (HR, AR) and one of the two commercial optical cements showed excellent resistance to neutrons and gamma radiations, and could be good candidates for the fabrication and utilization of optical components in extreme radiation environments. The data allowed several Chinese glasses to be studied for the first time.     

Workstation redesign for a repetitive drill press operation: A combined work design and ergonomics approach

A typical or conventional workstation for a repetitive drill press operation was evaluated and subsequently redesigned by incorporating the concepts and principles of work design and ergonomics. The production task comprised of drilling four holes on a prepared steel plate. A methods–time measurement (MTM) analysis was conducted to eliminate unnecessary motions and improve the necessary (work) motions involved in task performance. The specific features of the redesigned workstation were specially designed equipment (jig, fixture, etc.), a suitable adjustable chair, proper work height, a placement of tools/equipment within reach envelope, and a comprehensive operator training method. An experimental investigation was conducted to evaluate and test the redesigned workstation in terms of operator productivity (production quantity and quality output) and satisfaction. The increases in quantity (number of holes drilled) and quality (number of good holes drilled) output were 22 and 50%, respectively, for the redesigned workstation compared to the typical or conventional workstation. The high improvement in quality output (50%) could be attributed to the improved design of the jig and fixture and the comprehensive operator training method, which emphasizes the quality aspect of production output. The improvement in operator satisfaction (scores) were highly significant. This investigation has demonstrated the beneficial effect of a combined work design and ergonomics approach, especially for the redesign of a workstation for a repetitive drill press operation. © 2007 Wiley Periodicals, Inc. Hum Factors Man 17: 395–410, 2007.