认知无线Mesh网络中权重感知的组播路由算法

提出了一种无线组播业务权重感知的无线链路权值计算算法(links weights computing, LWC),在此基础上,提出了一种基于动态规划的满足QoS约束的分布式组播路由与频谱分配算法(weight-aware multicast routing algorithm, WMRA).WMRA算法的目标是最小化总的信道冲突值,同时考虑已接受组播业务的权重,高权重的组播业务相比低权重的组播业务具有较低的信道冲突值.WMRA算法首先采用LWC算法计算无线链路权值;然后,基于动态规划分布式地计算最小信道冲突值;最后,进行组播路由路径的构造,并进行频谱分配.仿真结果表明WMRA能达到预定目标,获得较低的信道冲突值.     

Influence of annealing on ZnO thin film grown by plasma-assisted MOCVD

ZnO films were grown on C-plane sapphire substrate by plasma-assisted MOCVD. The films was characterized by XRD, photoluminescence (PL) and the optical transmission spectrum. We found tensile strain in the sample, which had been annealed many times during the growth process, while there is compressive strain in the sample, which was annealed only one time after growth. The PL spectra at room temperature for the sample annealed many times exhibited only one emitting peak at around 380 nm. However, we find Γ₅ and Γ₆ free exciton peaks in the sample annealed only one time after growth. At the same time, the optical transmission indicate that the maximum of the sample's transmission decreases against with the increasing of the c-axis length in ranges from 190 to 900 nm.     

Effect of the stirring rate on physical and electrochemical properties of LiMnPO4 nanoplates prepared in a polyol process

In a polyol approach to make olivine-typed LiMnPO₄ nanoplates, the effect of the stirring rate on physical and electrochemical properties of the obtained sample has been symmetrically investigated for the first time. The as-prepared powders exhibit well crystalline olivine structure as presented by X-ray diffraction analysis. The secondary particles with a size of 2–3 μm are composed of aggregated nanoplates as verified by particle size analysis and field emission scanning electron microscopy measurement. Transmission electron microscopy presents that the nanoplate is about 18 nm thick along a-axis. The discharge capacity of the sample prepared under a stirring rate of 700 rpm reaches 150 mAh g⁻¹ when cycled at 0.05C after a few cycles.     

A 70 MPa hydrogen-compression system using metal hydrides

The objective of this work was to develop a 70 MPa hydride-based hydrogen compression system. Two-stage compression was adopted with AB₂ type alloys as the compression alloys. Ti_0.95Zr_0.05Cr_0.8Mn_0.8V_0.2Ni_0.2 and Ti_0.8Zr_0.2Cr_0.95Fe_0.95V_0.1 alloys were developed for the compression system. With these two alloys, a 70 MPa two-stage hydride-based hydrogen compression system was designed and built with hot oil as the heat source, and composite materials formed by mixing hydrogen storage alloys with Al fiber were used to prevent hydride bed compaction and to prevent strain accumulation. The experimental results showed that Ti_0.95Zr_0.05Cr_0.8Mn_0.8V_0.2Ni_0.2 and Ti_0.8Zr_0.2Cr_0.95Fe_0.95V_0.1 alloys could well meet the requirements of compression system. Composite materials formed by mixing hydrogen storage alloys with Al fiber were an effective way to prevent strain accumulation for hydride compression. With cold oil (298 K) and hot oil (423 K) as the cooling and heating sources, the built compression system could convert hydrogen pressure from around 4.0 MPa to over 70 MPa.     

Electrical and dielectric properties of polypropylene nanocomposites based on carbon nanotubes and barium titanate nanoparticles

Functional polypropylene (PP) nanocomposites were prepared by melt compounding with multiwalled carbon nanotubes (MWNT) as the electrically conductive component and barium titanate (BT) spherical nanoparticles as the ferroelectric component. To make PP electrically conductive, more than 3 wt.% MWNT is required. Surface modification of either MWNT or BT with titanate coupling agent further improves the electrical conductivity of the PP/MWNT/BT ternary nanocomposites. Interestingly, by modifying both MWNT and BT, 2 wt.% MWNT are sufficient to make the ternary nanocomposite electrically conductive. In addition, the incorporation of MWNT greatly increases the dielectric permittivity of PP/BT nanocomposites. However, to retain a low dielectric loss, the MWNT loading should be slightly less than the percolation threshold of the nanocomposites. The improved electrical conductivity and dielectric properties make the ternary nanocomposites attractive in practical applications.     

Geometric optimization of electrostatic fields for stable levitation of metallic materials

Experimental and computational methods are used to optimize the electrostatic field for levitating metallic materials.The calculated launch voltage increases linearly with the distance between top and bottom electrodes.The combination of a larger top electrode diameter with a smaller bottom diameter may enhance the levitation ability because the electric field intensity near the levitated sample is strengthened.Top convex and bottom concave electrodes can guarantee good levitation stability but decrease the levitation force.The design of bottom electrode is crucial to attain not only a stable levitation state but also a higher levitation capability.As a measure characterizing the intrinsic levitation ability of various materials,the product of density and diameter of levitated samples can be used to determine the launch voltage for counteracting gravity according to a power relationship.     

Cross-linked proton exchange membranes for direct methanol fuel cells: Effects of the cross-linker structure on the performances

A highly sulfonated poly (ether ether ketone) with pendant amino groups (Am-SPEEK) has been synthesized. The resulting copolymer showed good solubility in common organic solvents. Then the pendant amino groups of the Am-SPEEK were utilized to react with two kinds of cross-linker, epoxy resin and dibromide, to yield various cross-linked membranes. After cross-linking, the membranes could not dissolve in common solvents, just became swollen. In generally, all the cross-linked membranes showed improved mechanical properties and high dimensional stabilities, whereas the uncross-linked membranes highly swollen or even dissolved in water at high temperature. The proton conductivity of the membranes increased with an increase in temperature. At 80 °C, all the cross-linked membranes showed high proton conductivity, in the range of 0.111–0.140 S cm⁻¹. Especially, the TMBP cross-linked membrane showed a proton conductivity of 0.140 S cm⁻¹, which was higher than that of Nafion 117 (0.125 S cm⁻¹). The membranes with high proton conductivity, good oxidative stability, and improved methanol residence have been successfully developed. Furthermore, the influence of different main chain of the cross-linker on the performance of the cross-linked membranes was also investigated.     

Characterization and electrochemical properties of carbon-coated Li4Ti5O12 prepared by a citric acid sol-gel method

Since carbon coating can effectively improve electrical wiring of Li₄Ti₅O₁₂ and thus enhance its high rate performance, a novel and simple citric acid sol-gel method for in situ carbon coating is employed in this study. The effects of the amount of the carbon source in the starting xerogel on the particle size, the resistance and the electrochemical performance of the synthesized Li₄Ti₅O₁₂ samples are systematically studied. The physical and electrochemical properties of the obtained samples have been characterized by XRD, TG-DSC, SEM, TEM, BET, A.C. impedance, galvanostatically charge-discharge and cyclic voltammetry tests. The results show that the initial amount of the carbon source in the starting xerogel is a critical factor which determines the content of the coated carbon and the pore volume, therefore governs the high rate performance of the Li₄Ti₅O₁₂/C composites. The Li₄Ti₅O₁₂/C composite with in situ carbon coating of 3.5 wt% exhibits the best electrochemical performance which delivers delithiation capacities of 143.6 and 133.5 mAh g⁻¹ with fairly stable cycling performance even after 50 cycles at 0.5C and 1C rate, respectively.     

无粘结预应力混凝土环向楼板的施工方法

某建筑工程首层环向楼板面积大，为无粘结预应力混凝土结构，沿环向施加预应力，预应力筋居中均匀布置，具有一定的施工难度，本文对该工程的施工方法作介绍。     

顶升纠正浅埋顶管下沉的一种补救方法

某浅埋曲线顶管工程(埋深小于3 m)贯通后发现在纵向长约15 m范围内高程低于设计高程超过15 cm,超出规范规定要求.论证施工方案找到了经济适用的施工方案进行轴线偏离问题的处理,主要包括对施工过程中的关键部位进行了强度、裂缝宽度验算分析,施工难度和经济技术方案的比较.工程实例采用本方案成功解决了顶管下沉的问题,具有经济实用、操作简单等优点.