Novel electrospun polymer electrolytes incorporated with Keggin‐type hetero polyoxometalate fillers as solvent‐free electrolytes for lithium ion batteries

In this study, solvent‐free nanofibrous electrolytes were fabricated through an electrospinning method. Polyethylene oxide (PEO), lithium perchlorate and ethylene carbonate were used as polymer matrix, salt and plasticizer respectively in the electrolyte structures. Keggin‐type hetero polyoxometalate (Cu‐POM@Ru‐rGO, Ni‐POM@Ru‐rGO and Co‐POM@Ru‐rGO (POM, polyoxometalate; rGO, reduced graphene oxide)) nanoparticles were synthesized and inserted into the PEO‐based nanofibrous electrolytes. TEM and SEM analyses were carried out for further evaluation of the synthesized filler structures and the electrospun nanofibre morphologies. The fractions of free ions and crystalline phases of the as‐spun electrolytes were estimated by obtaining Fourier transform infrared and XRD spectra, respectively. The results showed a significant improvement in the ionic conductivity of the nanofibrous electrolytes by increasing filler concentrations. The highest ionic conductivity of 0.28 mS cm^?1 was obtained by the introduction of 0.49 wt% Co‐POM@Ru‐rGO into the electrospun electrolyte at ambient temperature. Compared with solution‐cast polymeric electrolytes, the electrospun electrolytes present superior ionic conductivity. Moreover, the cycle stability of the as‐spun electrolytes was clearly improved by the addition of fillers. Furthermore, the mechanical strength was enhanced with the insertion of 0.07 wt% fillers to the electrospun electrolytes. The results implied that the prepared nanofibres are good candidates as solvent‐free electrolytes for lithium ion batteries. © 2020 Society of Chemical Industry     

In situ measurements of human cough aerosol hygroscopicity

The airborne dynamics of respiratory droplets, and the transmission routes of pathogens embedded within them, are governed primarily by the diameter of the particles. These particles are composed of the fluid which lines the respiratory tract, and is primarily mucins and salts, which will interact with the atmosphere and evaporate to reach an equilibrium diameter. Measuring organic volume fraction (OVF) of cough aerosol has proved challenging due to large variability and low material volume produced after coughing. Here, the diametric hygroscopic growth factors (GF) of the cough aerosol produced by healthy participants were measured in situ using a rotating aerosol suspension chamber and a humidification tandem differential mobility analyser. Using hygroscopicity models, it was estimated that the average OVF in the evaporated cough aerosol was 0.88 ± 0.07 and the average GF at 90% relative humidity (RH) was 1.31 ± 0.03. To reach equilibrium in dry air the droplets will reduce in diameter by a factor of approximately 2.8 with an evaporation factor of 0.36 ± 0.05. Hysteresis was observed in cough aerosol at RH = ∼35% and RH = ∼65% for efflorescence and deliquescence, respectively, and may depend on the OVF. The same behaviour and GF were observed in nebulized bovine bronchoalveolar lavage fluid.     

Mechanics of plain-woven fabrics for inflated structures

Pressurized fabric tubes, pressure-stabilized beams (known as air beams) and air-inflated structures are considered to be valuable technologies for lightweight, rapidly deployable structures. Design optimization of an inflated structure depends on a thorough understanding of woven fabric mechanics. In this paper the bending response of woven pressure-stabilized beams have been experimentally tested and analytically investigated. Additionally, the micromechanical effects of interacting tows have been studied through finite element models containing contact surfaces and nonlinear slip/stick conditions. Local unit cell models consisting of pairs of woven tows were created to characterize the effective constitutive relations. The material properties from the unit cell models were then used for the global continuum model subjected to 4-point flexure. An experimental set-up was designed and manufactured for testing of Vectran and PEN air beams. The air beam mid-span deflections were measured as functions of inflation pressure and bending load. Plots of the elastic and shear moduli with respect to the pressure and coefficient of friction have been generated. It was determined that the effective elastic and shear moduli were functions of inflation pressure, the material used and the geometry of the weave. It was shown that pneumatic or pressurized tube structures differ fundamentally from conventional metal structures.     

Bayesian estimation based on vague lifetime data

In Classical Bayesian approach, estimation of lifetime data usually is dealing with precise information. However, in real world, some informations about an underlying system might be imprecise and represented in the form of vague quantities. In these situations, we need to generalize classical methods to vague environment for studying and analyzing the systems of interest. In this paper, we propose the Bayesian estimation of failure rate and mean time to failure based on vague set theory in the case of complete and censored data sets. To employ the Bayesian approach, model parameters are assumed to be vague random variables with vague prior distributions. This approach will be used to induce the vague Bayes estimate of failure rate and mean time to failure by introducing and applying a theorem called “Resolution Identity” for vague sets. In order to evaluate the membership degrees of vague Bayesian estimate for these quantities, a computational procedure is investigated. In the proposed method, the original problem is transformed into a nonlinear programming problem which is then divided into eight subproblems to simplifying computations.     

Analytical Modeling of Short-Channel Fully-Depleted Triple Work Function Metal Gate (TWFMG) SOI MESFET

Silicon - In this paper, a new structure: triple work function metal gate SOI MESFET, intended for integration into the deep-submicron CMOS technology, is proposed. The gate of the device consists...     

Using plasmonic cloaking method on infinite cylindrical structures and its applications

Journal of Computational Electronics - In recent years, cloaking using materials with negative electric permittivity or magnetic permeability has been studied and researched. It has been...     

Experimental determination of gas holdup and volumetric mass transfer coefficient in a jet bubbling reactor

The hydrodynamics and mass transfer characteristics of a lab-scale jet bubbling reactor(JBR) including the gas holdup, volumetric mass transfer coefficient and specific interfacial area were assessed experimentally investigating the influence of temperature, p H and superficial gas velocity. The reactor diameter and height were 11 and 30 cm,respectively. It was equipped with a single sparger, operating at atmospheric pressure, 20 and 40℃, and two p H values of 3 and 6. The height of the liquid was 23 cm, while the superficial gas velocity changed within 0.010–0.040 m·s~(-1) range. Experiments were conducted with pure oxygen as the gas phase and saturated lime solution as the liquid phase. The liquid-side volumetric mass transfer coefficient was determined under unsteady-state oxygen absorption in a saturated lime solution. The gas holdup was calculated based on the liquid height change, while the specific interfacial area was obtained by a physical method based on the bubble size distribution(BSD) in different superficial gas velocities. The results indicated that at the same temperature but different p H, the gas holdup variation was negligible, while the liquid-side volumetric mass transfer coefficient at the p H value of 6 was higher than that at the p H = 3. At a constant p H but different temperatures, the gas holdup and the liquid-side volumetric mass transfer coefficients at 40℃ were higher than that of the same at 20℃. A reasonable and appropriate estimation of the liquid-side volumetric mass transfer coefficient(kla) in a pilot-scale JBR was provided which can be applied to the design and scale-up of JBRs.     

Using the genetic algorithm to enhance nonnegative matrix factorization initialization

Nonnegative matrix factorization (NMF) algorithms have been utilized in a wide range of real applications; however, the performance of NMF is highly dependent on three factors including: (1) choosing a problem dependent cost function; (2) using an effective initialization method to start the updating procedure from a near‐optimal point; and (3) determining the rank of factorized matrices prior to decomposition. Due to the nonconvex nature of the NMF cost function, finding an analytical‐based optimal solution is impossible. This paper is aimed at proposing an efficient initialization method to modify the NMF performance. To widely explore the search space for initializing the factorized matrices in NMF, the island genetic algorithm (IGA) is employed as a diverse multiagent search scheme. To adapt IGA for NMF initialization, we present a specific mutation operator. To assess how the proposed IGA initialization method efficiently enhances NMF performance, we have implemented state‐of‐the‐art initialization methods and applied to the Japanese Female Facial Expression dataset to recognize the facial expression states. Experimental results demonstrate the superiority of the proposed approach to the compared methods in terms of relative error and fast convergence.     

Surface modification of ultra‐high‐molecular‐weight polyethylene. II. Effect on the physicomechanical and tribological properties of ultra‐high‐molecular‐weight polyethylene/poly(ethylene terephthalate) composites

We performed surface modification of ultra‐high‐molecular‐weight polyethylene (UHMWPE) through chromic acid etching, with the aim of improving the performance of its composites with poly(ethylene terephthalate) (PET) fibers. In this article, we report on the morphology and physicomechanical and tribological properties of modified UHMWPE/PET composites. Composites containing chemically modified UHMWPE had higher impact properties than those based on unmodified UHMWPE because of improved interfacial bonding between the polymer matrix and the fibers and better dispersion of the fibers within the modified UHMWPE matrix. Chemical modification of UHMWPE before the introduction of PET fibers resulted in composites exhibiting improved wear resistance compared to the base material and compared to unmodified UHMWPE/PET composites. On the basis of the morphological studies of worn samples, microploughing and fatigue failure associated with microcracking were identified as the principle wear mechanisms. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006