Effects of Winding Attachment Positions on Output Characteristics of Flux‐Modulating Synchronous Machines

The flux‐modulating synchronous machine (FMSM) is a new type of multipole SM with nonoverlapping concentrated armature and field windings on the stator. This paper compares the output characteristics of two FMSMs through finite element analysis (FEA) and experiments. In both of the FMSMs, the attachment positions of the armature and field windings are swapped. To determine the reason for the discrepancies in their output characteristics, unsaturated inductances were calculated using a d‐‐q equivalent circuit. In addition, the calculated results of the inductances were confirmed through a visualization of the leakage fluxes using FEA. The results of the study show that the synchronous inductance can be reduced by attaching the armature winding to the air‐gap side of the stator teeth and that the reduction leads to an increase in output power.     

Correlation between motion of source bender element and feedback signal induced by self-monitoring

Since the introduction of bender element tests to soil testing, the reliability of the estimated travel time has been the most serious problem. The author has previously shown a potential solution whereby removing the response of the bender element subsystem from the whole response could dramatically improve the accuracy of the travel time estimation. In order to lay the foundation for estimating the response of the bender element subsystem, this paper examines the correlation between the displacements of the element and the induced feedback signals by employing a self-monitoring element. The response of the self-monitoring element is modeled as a transfer function involving two internal transfer functions that relate the input signals to the displacements and the displacements to the feedback signals, respectively. Using a laser displacement sensor, the displacements are directly measured through the entire surface and reveal the three-dimensional bending motion of the element oscillating in both longitudinal and width directions. The feedback signals are similar to, but inconsistent with, the tip displacements, and an attempt is made to correct the feedback signals. Finally, a conclusion is given on the potential for estimating the response of the bender element subsystem using the self-monitoring element.     

On maximum-length linear congruential-sequences-based low-density parity-check codes

This letter extends a low-density parity-check code construction using maximum-length linear congruential sequences by Prabhakar and Narayanan. The corresponding bipartite graphs of their construction were guaranteed to have a girth larger than four by a sufficient condition. However, their sufficient condition was limited to regular codes and data-node degree equal to three. The extension in this letter allows arbitrary data-node degrees and is applicable to irregular codes. Further, simpler sufficient conditions are derived and larger girths are addressed.     

二垩英与资源回收-Ⅰ考虑到二垩英生成的资源与能量回收基础研究

目前在日本,存在大量工业垃圾,包括各种塑料制品,ASR(汽车破碎垃圾),含有毒PCB(多氯联苯)的110变压器和PVC(聚氯乙稀)制品等.而来自城市垃圾焚烧炉的废气含有大量能量.因此,在充分考虑环境、避免二垩英生成的同时,安全回收来自工业垃圾、城市和/或工业垃圾焚烧炉的资源和能量是个非常重要的课题,这也将对抑制CO2排放作出贡献.正确地阐明焚烧过程中二垩英的生成机理及详细研究含少量二垩英的焚烧废气在冷却过程中大量形成二垩英的临界温度是项很重要的工作.解决这个问题可有效实现资源和能量的回收.本报告介绍日本在二垩英排放方面目前采取的对策和存在的问题以及大阪大学为阻止二垩英生成所做的基础研究工作.     

Cloning of a novel signal-transducing adaptor molecule containing an SH3 domain and ITAM

We molecularly cloned a cDNA coding for a novel phosphotyrosine molecule with a 70 kDa molecular mass, named STAM (signal transducing adaptor molecule), which is tyrosine-phosphorylated rapidly after stimulation with various cytokines such as IL-2, IL-3, IL-4, IL-7, GM-CSF, EGF and PDGF. STAM contains an SH3 (Src-homology 3) domain and the ITAM (immunoreceptor tyrosine-based activation motif), suggesting that STAM acts as an adaptor molecule involved in signal transducing pathways from the cytokine receptors.     

Osteoclastic features of multinucleated giant cells responding to synthetic hydroxyapatite implanted in rat jaw bone.

Multinucleated giant cells (MGCs) that responded to synthetic hydroxyapatite (HAP) implanted in rat mandibles were studied with electron microscopy. HAP used in this study sintered at 200 degrees C (HAP200) and at 125 degrees C (HAP1250) after the synthesis by a wet method. One to three weeks after the intraosseous implantation of HAP, MGCs responding to HAP200 had not only well-developed ruffled border and the clear zone but well-developed perinuclear Golgi complex, many mitochondria and vesicles in their cytoplasms. MGCs responding to HAP1250 had the clear zone, but not the ruffled border although they showed similar cytoplasmic features to those of MGCs responding to HAP200. They merely extended short slender cytoplasmic processes to HAP1250. These results suggest that although osteoclast-like MGCs respond to HAP implanted in the bone, the development of the ruffled border-clear zone system depends on physicochemical properties of HAP.     

Stereoscopic synthesized brain-surface imaging with MR angiography for localization of a peripheral mycotic aneurysm: case report

A patient with subacute bacterial endocarditis and a peripheral mycotic aneurysm is presented. We used a combined multi-slice surface anatomy scanning (SAS) and contrast-enhanced MR angiography image to determine the exact location of the small lesion by applying a skin marker on the scalp and visualizing the relationship of the marker to the brain surface structures and to the lesion. This technique was useful for the removal of a small peripheral aneurysm using only a limited craniotomy.     

Reliability of Au bump––Cu direct interconnections fabricated by means of surface activated bonding method

As a room temperature bonding method, surface activated bonding (SAB) method has been introduced to be one of the most appropriate interconnection methods for the next generation of electronic packaging. Thus it is important to study the reliability of SAB interconnection in long term life test.In this paper, interconnections of Au bump and Cu film bonded by SAB method were performed in high temperature thermal aging test. Degradation of properties such as electrical resistance, shear strength of bump and interface microstructure during aging process were studied to investigate the failure mechanism of the interconnection. Intermetallic compound Cu₃Au was found formed at the interface during thermal aging, and it causes evolvement of the properties and failure mode of the interconnection changing in shear test. Results reveal that SAB is suitable for the interconnection between Au bump and Cu film and it is reliable in thermal reliability test.     

The heat transfer and pressure drop characteristics of finned tube banks in forced convection (effects of fin height on pressure drop characteristics)

In recent years the requirement for the reduction of energy consumption has been increasing to solve the problems of global warming and the shortage of petroleum resources. For example, in the power generation field, as thermal power generation occupied 60% of the power generation demand, considerable improvement of the thermal efficiency is required. This paper describes the pressure drop characteristics of finned tube banks used for heat exchangers in thermal power generation that were clarified by testing serrated finned tube banks with different fin heights for improved heat transfer and conventional spiral finned tube banks with different fin heights, and an equation to predict pressure drop which is necessary for the heat exchanger design is proposed. © 2006 Wiley Periodicals, Inc. Heat Trans Asian Res, 35(3): 179–193, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20112