Decreased CD10-positive granulocytes for the differential diagnosis of myelodysplastic syndrome

Myelodysplastic syndromes (MDS) are highly heterogeneous myeloid neoplasms, and a large number of patients are difficult to diagnose and classify by blood and bone marrow examination. As a surface marker of granulocyte, studies have shown CD10 can be used to define the degree of granulocyte maturation in MDS patients. However, whether it can be used for differential diagnosis of MDS and other hematological diseases remains inconclusive. To explore the value of CD10 for differential diagnosis of MDS, 60 newly diagnosed MDS, 20 aplastic anemia (AA) patients, and 35 iron-deficient anemia (IDA) patients were selected for this study. Bone marrow (BM) specimens were processed for surface marker analysis and labeled with pre-conjugated monoclonal antibodies. Stained cells were detected by flow cytometry. Our results indicated that CD10-positive granulocytes were significantly decreased in BM of MDS patients than AA and IDA patients, and the level of CD10-positive mature granulocytes was not associated with the clinical stages of malignancy. Receiver operating characteristic (ROC) areas under the curve (AUC) of CD10-positive granulocytes was 0.86 and 0.85, respectively, in MDS patients than the IDA group and AA group with good specificity and sensitivity. Further, CD10-positive granulocytes were increased after effective treatment. In conclusion, we found the decrease in CD10-positive granulocytes has a differential diagnostic value of MDS.     

空间相机中的偏流角分析

高分辨率星载TDI-CCD相机在成像过程中,偏流角会对相机的成像质量产生影响.因此根据卫星轨道方程给出了偏流角和偏流角角速度随纬度变化的具体形式,基于此分别研究了偏流角在卫星穿航方向和沿航方向引起的像移量和它对相机成像质量的影响.结果表明,偏流角是纬度的函数,由它引起的像移在穿航方向对相机像质的影响较为严重,必须加以校正.并针对极地圆轨道详细计算了像移对像质的影响程度和在MTF偏流角＞0.95的情况下偏流角需要调整的最小时间间隔.     

氮化硅/石墨激光合金化涂层的组织结构与性能研究

为获得金属表面特别是高副接触金属表面含自润滑特性且具有高硬度耐磨特性的功能材料 ,研究了 45 # 钢表面激光合金化氮化硅 /石墨复合涂层的工艺方法、组织特征、界面形态及其形成机制 ,利用光学显微镜、扫描电镜和X射线能谱对所形成合金化层的元素分布和含量进行了分析 ,并对试样硬度进行了测定。结果表明 ,合金化层中元素Fe ,Co ,Si,C分布均匀 ;C含量达到了 15 6 9%,大部分以石墨的形式存在 ,具有一定的自润滑性能 ;但在形成合金化层的温度条件下 ,氮化硅分解严重 ;合金化层硬度提高的主要原因是Si Fe ,Co Fe固溶体的强化作用及高碳马氏体的生成和高硬度碳化物的存在。     

A Special Structure in Al-Mg-Li Alloy (01420) Weld Metal

A large quantity of laminated fine grain zones were observed in the Al-Mg-Li alloy weld metal by manual TIG, which was not found in ordinary Al alloy welds. The fine grain zone is formed because of the Al3(Zr,Ti) particles in the filler metal and the manual filling of filler metal in welding process     

高温预析出对Al-Zn-Mg系铝合金时效硬化和应力腐蚀的影响

研究了高温固溶后降温处理工艺对中强可使预析出LC52和7039铝合金的组织、时效硬化和应力腐蚀的影响。金相观察发现,高温预析出可优先在晶界处产生,并提高随后时效状态下晶界析出相的不连续分布程度,温度降低到一定程度晶内和晶界产生大量析出。合金拉伸性能和应力腐蚀结果表明,预析出在保持强度和塑性的同时,可提高抗应力腐蚀性能。而预析出温度降低,合金强度呈下降趋势。     

江川灌区改革措施与经验

根据灌区发展存在的有关问题,分析了存在问题的原因,提出了改变以往职工“铁饭碗”,用水户“大锅水”的思维模式,宣传新的灌区发展模式,以促进灌区的可持续发展。     

浅议提高电除尘效率的对策和方法

介绍了电除尘器的发展现状,分析了影响电除尘器除尘效率的问题,提出了低压控制系统的自控改造方案,以提高自控水平和除尘效率。该方案实际应用之后,获得了较为理想的效果。     

天然气长输管道泄漏检测方案对比

大口径、长距离天然气输送管道的泄漏检测和定位技术日益受到人们的重视。总结评价了用于天然气长输管道泄漏检测和安全预警的各种技术方案，讨论了其基本原理、适用范围、技术成熟度、优点和缺点以及工程应用情况；采用灵敏度、定位精度等7项技术指标对各种泄漏检测方法进行了评价和对比。目前，音波泄漏检测技术和分布式光纤泄漏检测技术由于具有诸多方面的优点，是近年来国内外泄漏检测技术研究的重点和热点，这两种技术已初步应用于实际，并取得了良好的效果。重点对这两种泄漏检测技术的原理、适用范围、所能达到的技术指标、优、缺点以及工程案例进行了详细讨论、分析和对比，可为我国天然气长输管道泄漏检测和安全预警系统的开发和研究提供技术依据。