Oxidative degradation of polyamide reverse osmosis membranes: Studies of molecular model compounds and selected membranes

Selected aromatic amides were used to model the chemical reactivity of aromatic polyamides found in thin‐film composite reverse osmosis (RO) membranes. Chlorination and possible amide bond cleavage of aromatic amides upon exposure to aqueous chlorine, which can lead to membrane failure, were investigated. Correlations are made of the available chlorine concentration, pH, and exposure time with chemical changes in the model compounds. From the observed reactivity trends, insights are obtained into the mechanism of RO membrane performance loss upon chlorine exposure. Two chemical pathways for degradation are shown, one at constant pH and another that is pH‐history dependent. An alternative strategy is presented for the design of chlorine‐resistant RO membranes, and an initial performance study of RO membranes incorporating this strategy is reported. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1173–1184, 2003     

An integrated system to remote monitor and control anaerobic wastewater treatment plants through the internet.

The TELEMAC project brings new methodologies from the Information and Science Technologies field to the world of water treatment. TELEMAC offers an advanced remote management system which adapts to most of the anaerobic wastewater treatment plants that do not benefit from a local expert in wastewater treatment. The TELEMAC system takes advantage of new sensors to better monitor the process dynamics and to run automatic controllers that stabilise the treatment plant, meet the depollution requirements and provide a biogas quality suitable for cogeneration. If the automatic system detects a failure which cannot be solved automatically or locally by a technician, then an expert from the TELEMAC Control Centre is contacted via the internet and manages the problem.     

The time course of plausibility effects on eye movements in reading: Evidence from noun-noun compounds.

Readers' eye movements were monitored as they read sentences containing noun-noun compounds that varied in frequency (e.g., elevator mechanic, mountain lion). The left constituent of the compound was either plausible or implausible as a head noun at the point at which it appeared, whereas the compound as a whole was always plausible. When the head noun analysis of the left constituent was implausible, reading times on this word were inflated, beginning with the first fixation. This finding is consistent with previous demonstrations of very rapid effects of plausibility on eye movements. Compound frequency did not modulate the plausibility effect, and all disruption was resolved by the time readers' eyes moved to the next word. These findings suggest (contra Kennison, 2005) that the parser initially analyzes a singular noun as a head instead of a modifier. In addition, the findings confirm that the very rapid effect of plausibility on eye movements is not due to strategic factors, because in the present experiment, unlike in previous demonstrations, this effect appeared in sentences that were globally plausible. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Formation and retention of local melted films in AZ91 friction stir spot welds

The formation of local melted films during friction stir spot welding of as-cast AZ91D and thixomolded AZ91 material is investigated. The average temperatures close to the tip of the rotating pin vary from 438 to 454 °C during the dwell period in friction stir spot welding. These measured temperature values are higher than the melting temperature of α-Mg + Mg₁₇Al₁₂ eutectic (437 °C). It is suggested that the temperature in the stir zone during the dwell period is determined by the relative proportions of α-Mg and (α-Mg + Mg₁₇Al₁₂) eutectic material, which are incorporated during friction stir spot welding. Based on the stir zone temperature measurements and a detailed examination of material located at the root of the pin thread it is suggested that material is moved downwards via the pin thread and into the stir zone during the dwell period in friction stir spot welding. Evidence of local melted film formation is observed in the stir zone of AZ91 spot welds. It is suggested that melted films are retained since their dissolution rate is much slower in the high temperature stir zone than it is when melted films is formed in the stir zone during Al 7075-T6 friction stir spot welding. The spontaneous melting temperature, solute diffusion rate and the thermodynamic driving force for droplet dissolution are much higher during Al 7075-T6 friction stir spot welding.     

Gelling of alginate fibres

Equipment was developed to measure the time for complete gelling of sodium alginate fibres in calcium chloride solution, taken as the time to achieve maximum tensile strength. The effects of fibre diameter, alginate concentration, alginate composition and calcium chloride concentration on gelling time were investigated. A diffusional model, developed to predict the gelling time, agreed with experimental results except for the effect of calcium ion concentration which was modelled empirically.     

Location of Aluminum in Substituted Calcium Silicate Hydrate (C-S-H) Gels as Determined by 29Si and 27Al NMR and EELS

Solid-state ²⁷Al and ²⁹Si magic angle spinning NMR spectroscopy has been combined with electron energy loss spectroscopy carried out in the transmission electron microscope to determine the location of Al substituting in a semicrystalline C-S-H gel present in a hydrated synthetic slag glass. The gel is found to contain mainly pentameric silicate chains in which the central silicon is substituted by aluminum.