High-purity mullite ceramics, promising engineering ceramics for high-temperature applications, were fabricated using transient liquid phase sintering to improve their high-temperature mechanical properties. Small amounts of ultrafine alumina or silica powders were uniformly mixed with the mullite precursor depending on the silica-alumina ratio of the resulting ceramics to allow for the formation of a transient liquid phase during sintering, thus, enhancing densification at the early stage of sintering and mullite formation by the reaction between additional alumina and the residual glassy phase (mullitization) at the final stage of sintering. The addition of alumina powder to the silica-rich mullite precursor resulted in a reaction between the glassy silica and alumina phases during sintering, thereby forming a mullite phase without inhibiting densification. The addition of fine silica powder to the mullite single-phase precursor led to densification with an abnormal grain growth of mullite, whereas some of the added silica remained as a glassy phase after sintering. The resulting mullite ceramics prepared using different powder compositions showed different sintering behaviors, depending on the amount of alumina added. Upon selecting an optimum process and the amount of alumina to be added, the pure mullite ceramics obtained via transient liquid phase sintering exhibited high density (approximately 99%) and excellent high-temperature flexural strength (approximately 320 MPa) at 1500 °C in air. These results clearly demonstrate that pure mullite ceramics fabricated via transient liquid phase sintering with compositions close to those of stoichiometric mullite could be a promising process for the fabrication of high-temperature structural ceramics used in an ambient atmosphere. The transient liquid phase sintering process proposed in this study could be a powerful processing tool that allows for the preparation of superior high-temperature structural ceramics used in the ambient processing atmosphere. 相似文献
Design and fabrication of lateral SiC reduced surface field (RESURF) MOSFETs have been investigated. The doping concentration (dose) of the RESURF and lightly doped drain regions has been optimized to reduce the electric field crowding at the drain edge or in the gate oxide by using device simulation. The optimum oxidation condition depends on the polytype: N/sub 2/O oxidation at 1300/spl deg/C seems to be suitable for 4H-SiC, and dry O/sub 2/ oxidation at 1250/spl deg/C for 6H-SiC. The average inversion-channel mobility is 22, 78, and 68 cm/sup 2//Vs for 4H-SiC(0001), (112~0), and 6H-SiC(0001) MOSFETs, respectively. RESURF MOSFETs have been fabricated on 10-/spl mu/m-thick p-type 4H-SiC(0001), (112~0), and 6H-SiC(0001) epilayers with an acceptor concentration of 1/spl times/10/sup 16/ cm/sup -3/. A 6H-SiC(0001) RESURF MOSFET with a 3-/spl mu/m channel length exhibits a high breakdown voltage of 1620 V and an on-resistance of 234 m/spl Omega//spl middot/cm/sup 2/. A 4H-SiC(112~0) RESURF MOSFET shows the characteristics of 1230 V-138 m/spl Omega//spl middot/cm/sup 2/. 相似文献
Behaviormetrika - In this paper, we propose a new clustering method based on the concept of maximum likelihood (ML) estimation. In general, the problem of local minima arises when we try to use the... 相似文献
In this paper, we propose a new hierarchical clustering method, which is useful to find appropriate clusters of attributes from given dichotomous or frequency data. Important features of our method are 1) the similarity between two attributes is defined as a probability of their pattern vectors being observed under the hypothesis of independence, 2) for each generated cluster, one pattern vector is defined in a natural manner, and 3) it can be used freely without distinguishing the frequency data from the dichotomous one.
A typical frequency data is analyzed to illustrate how our method works effectively. The discussion on similarities among objects is also included to propose a new similarity measure based on our clustering method.
Here various approaches to understanding the complex relationship among the local atomic arrangements, the distribution of charge/holes and the superconductivity characteristics are discussed for a variety of multi-layered copper-oxide superconductors. Regarding the structural parameters, i.e. bond lengths and angles, no single parameter is revealed to control the superconductivity characteristics alone. As a matter of fact, superconductivity properties are found to be correlated with the whole delicately balanced fine-structure that is described by a set of multiple parameters: it is shown that Tc and Hirr are enhanced in somewhat opposite ways. Expressing the delicately balanced fine-structure through the charge/hole distribution, it is concluded that the more homogeneously distributed the charge carriers are the more enhanced is the Hirr characteristics, while the opposite is likely to apply to the Tc value. 相似文献
Differentiation of endometrial stromal cells (decidualization) is essential for embryo implantation and maintenance of pregnancy. By sequential complementary DNA subtractive hybridization, one of the messenger RNAs (mRNA) induced by progesterone in human endometrial stromal cells decidualized in vitro was identified as that of a tissue transglutaminase type II (TGase). TGase mRNA was induced within 6 h after the addition of progesterone to the culture, and the effect was dose dependent. Both the TGase inhibitor monodansylcadaverine and oligodeoxynucleotide complementary to the TGase mRNA inhibited the decidualization, as assessed by PRL production and morphological transformation. Expression of TGase mRNA in human decidua and endometria exposed to high levels of progesterone in vivo was demonstrated by Northern blotting and in situ hybridization. These data suggest that TGase is necessary for the decidualization of human endometrial stromal cells and that clarification of the mechanism of action of TGase will facilitate further insight into the diagnosis and treatment of infertility. 相似文献
Porous and electrically conducting carbon-clay composites were prepared by firing mixtures of carbon powder (0 to 20 wt%) and clay minerals. They showed porosity of 50 to 65% and had high mechanical strength (compressive strength = 130 to 400 kg cm–2) as well as high resistance against thermal oxidation in air. Their electrical conductivity, , increased with increasing carbon content levelling off at about 20 wt% of carbon content to give a value of about 2 S cm–1. Formation of carbon chains is considered to be responsible for the electrical conduction in the composite, and a model to correlate the electrical conductivity with the carbon content has been proposed by modifying a model previously proposed by Scarisbrick. 相似文献
A mist of a hydrosol consisting of silica, alumina/NaAlO2 and sodium hydroxide was produced by a supersonic atomization, and treated successively in three furnaces of different temperatures. The temperatures of the furnaces were adjusted for the evaporation of water, the dehydration and the crystallization of the mixed oxide, respectively. The spherical particles ( 0.5m) of carnegieite were found to be formed in a narrow composition range of the raw materials at temperatures of 650 to 900° C. The factors affecting the properties of the particles were investigated. 相似文献