薄层罩面在高速公路预防性养护中的应用

结合广珠西高速路面超薄磨耗层的具体应用,论述了超薄磨耗层对原材料技术要求、配合比设计、施工工艺和施工关键技术控制等。     

餐饮废油生物柴油低温流动性的改进研究

使用气-质联用仪测定餐饮废油生物柴油(WCME)和-10号柴油(-10PD)的组成,使用冷滤点试验器和运动黏度试验器测定WCME的低温流动性,同时使用调合、添加低温流动性改进剂的方法改进WCME的低温流动性。实验结果表明,WCME主要由饱和脂肪酸甲酯和不饱和脂肪酸甲酯组成,质量分数分别为27.63%和71.81%;WCME冷滤点为0℃,运动黏度(40℃)为4.41mm2/s;WCME与-10PD调合后,冷滤点降低,其中B20的冷滤点最低,为-13℃,运动黏度随着WCME的体积分数的减少,逐渐接近-10PD的运动黏度。通过添加低温流动性改进剂,WCME,B10,B20的冷滤点分别从0,-8,-13℃降至-4,-26,-25℃。     

Characteristic of polysaccharides from Flammulina velutipes in vitro digestion under salivary,simulated gastric and small intestinal conditions and fermentation by human gut microbiota

In this study, in vitro digestion and fermentation of Flammulina velutipes -derived polysaccharides (FVP) were investigated. It was found that FVP mainly consisted of 48.45% glucose, 15.40% mannose, 14.60% xylose, 11.80% fucose and 9.90% galactose. The -human saliva, simulated gastric and small intestinal juices conditions did not break down the FVP. Based on in vitro fermentation tests, FVP modulated the composition of gut microbiota by elevating the amounts of Bifidobacteriaceae and Bacteroidaceae and reducing the numbers of genera Lachnospiraceae and Enterococcaceae. Meanwhile, FVP affected the synthesis of short-chain fatty acids derived from gut microbiota.     

Effects of Undercooling and Transformation Time on Microstructure and Strength of Fe–C–Mn–Si Superbainitic Steel

Strength of Materials - A metallographic method, dilatometry, and X-ray diffraction were applied to investigate the effects of undercooling and holding time on bainitic transformation,...     

Spreading and Curing Behaviors of a Thermosetting Droplet-Silicone on a Heated Surface

Thermosetting materials are widely used as encapsulation in the electrical packaging to protect the core electronic components from external force, moisture, dust, and other factors. However, the spreading and curing behaviors of such kind of fluid on a heated surface have been rarely explored. In this study, we experimentally and numerically investigated the spreading and curing behaviors of the silicone(OE6550 A/B, which is widely used in the light-emitting diode packaging) droplet with diameter of ～2.2 mm on a heated surface with temperature ranging from 25 ℃ to 250 ℃. For the experiments, we established a setup with high-speed camera and heating unit to capture the fast spreading process of the silicone droplet on the heated surface. For the numerical simulation, we built a viscosity model of the silicone by using the Kiuna's model and combined the viscosity model with the Volume of Fluid(VOF) model by the User Defined Function(UDF) method. The results show that the surface temperature significantly affected the spreading behaviors of the silicone droplet since it determines the temperature and viscosity distribution inside the droplet. For surface temperature varied from 25 ℃ to 250 ℃, the final contact radius changed from ～2.95 mm to ～1.78 mm and the total spreading time changed from ～511 s to ～0.15 s. By further analyzing the viscosity evolution of the droplet, we found that the decreasing of the total spreading time was caused by the decrease of the viscosity under high surface temperature at initial spreading stage, while the reduction of the final contact radius was caused by the curing of the precursor film. This study supplies a strategy to tuning the spreading and curing behavior of silicone by imposing high surface temperature, which is of great importance to the electronic packaging.     

Torsional statics of two-dimensionally functionally graded microtubes

A size-dependent governing equation is derived to investigate the torsional static behaviors of two-dimensionally functionally graded microtubes based on the modified couple stress theory. The shear modulus is assumed to vary along the tube’s length direction according to an exponential distribute function, and varies along the tube’s radius direction according to a power-law function. A generalized differential quadrature method is developed to determine the rotational angle and shear stresses. Some illustrative examples are given to investigate the effects of applied torques, the length scale parameter and various material compositions on the torsional angle and shear stresses.