Detection of Multiple Blockages in Parallelized Microreactors

In a plant consisting of parallelized microreactors (MRs), the product quality is lowered because of a lack of flow uniformity among them when blockage occurs. It is not practical to install sensors in every MR from the viewpoint of cost when detecting the blocked MRs. In the previous study, the multiple blockage detection (MBD) method using a small number of sensors was proposed, but its performance became low when the number of sensors decreased. Here, the conventional algorithm for MBD is improved by considering the process behavior on blockage occurrence, and the effectiveness of the improved algorithm is demonstrated through a numerical case study. The effects of flow distributor types and sensor types on the MBD performance are numerically investigated.     

Nondestructive readout mode static induction transistor (SIT) photosensors

The nondestructive readout (NDRO) performance of two static induction transistor (SIT) photosensors, a 40×40 pixel area array and a 140-b linear array, is examined. NDRO operation in the SIT sensors is demonstrated by imaging with the area array and by examining the output waveform of the linear array. The charge lost per NDRO cycle in the linear array was 0.014% near the saturation signal level, and no charge loss could be detected at the ⩽0.5 saturation level. NDRO performance in the area array was degraded compared to the linear array, due to the larger value of the load capacitance connected to the output electrode of the SIT. NDRO operation also enables the cancellation of both the photosite reset noise and the signal nonuniformity by subtracting the first NDRO output from the following NDRO outputs, as well as the advantage of monitoring the signal state during the integration period     

Superplastic behaviour of Ti-48at.%Al two-phase titanium aluminide compacts made from mechanically alloyed powder

An HIP compact of MA-processed powder having a nominal composition of Ti-48at.% Al was produced. The compact consisted of a large amount of TiAl(λ) and a small amount of Ti₃Al (₂), in a completely ultra-fine equiaxed grain structure. This two-phase compact showed typical superplastic deformation behaviour. A maximum elongation of 550% was obtained. A strain exponent, n = 2, and grain size exponent, p = 2, were determined from the results of a strain-rate-change test and a creep test at constant initial stress using samples having various grain sizes, respectively. The activation energy for creep, Q_c at constant stress was calculated to be 350 kJ/mole. It is concluded that the superplastic deformation mechanism of the material under study is grain boundary sliding controlled by lattice diffusion in the TiAl phase.     

Time-space method for multidimensional melting and freezing problems

In this paper, the time–space method (TSM) for multidimensional melting and solidification problems is proposed. In the proposed TSM, the timewise co-ordinate is incorporated into one of the spatial co-ordinates, thereby transforming the usual transient 2-D (or 3-D) problems into steady 3D (or 4-D) boundary-value problems. Since time integration is not necessary, the TSM has a feature that eliminates the so-called numerical instability which has been a great concern in the principal numerical methodologies in the past. That is, no error propagation in the timewise direction occurs in the TSM calculation. The TSM is applicable to almost all transient heat transfer and flow problems. The computer running time will be reduced to only 1/100th–1/1000th of the existing schemes for 2-D or 3-D problems. The sample calculations are presented for a 2-D melting problem in a square cavity and the validity of the present method is examined.     

Elevated serum lipoprotein (a) levels associated with ulcerative colitis in a young Japanese patient

Thromboembolism has been shown to play a role in the pathogenesis of inflammatory bowel disease (IBD). A possibility exists that lipoprotein (a) [Lp(a)], a newly-discovered prothrombotic factor, also participates in the development of at least some cases of IBD. Marked elevation of serum Lp(a) levels was observed in a young patient with ulcerative colitis. A biopsy specimen of the rectal mucosa showed findings compatible with ulcerative colitis, as well as small vessel thrombus occurring within the muscularis mucosa in the rectum. Serum Lp(a) levels were markedly elevated on admission (71 mg/dl), with a gradual decrease to 46 mg/dl on discharge. Moreover, serum Lp(a) levels decreased in parallel with clinical improvement. In the quiescent clinical stage, no small vessel thrombus was observed in the mucosa on follow-up colonoscopy. The association between IBD and hyper-Lp(a)-emia would be presumable but it has been, to our knowledge, previously unreported. The case reported here would be the first young patient, suggesting the presence of hyper-Lp(a)-emia and small vessel thrombus formation occurring in association with the development of ulcerative colitis.     

GBLT-VG for High User Densities by User Group Behavior and Hot Point in MMO Virtual Environment

Massively Multiplayer Online (MMO) games have large-scale virtual environments. Here, we propose a load distribution technique called the Group Based Load-distribution Technique with Virtual Group (GBLT-VG) that utilizes Peer-to-Peer (P2P) communication to maintain scalability under high user density conditions in MMO virtual environments. A common problem of P2P virtual environments is that user group behavior frequently generates high user density conditions. Existing techniques to manage the virtual environment cannot maintain performance in such high user density situations. The proposed technique, GBLT-VG, reduces area management loads of manager peers by introducing a new manager who manages a user neighbor group. GBLT-VG forms the user neighbor group efficiently by using party function under high user density conditions caused by users?? cooperative behaviors. In addition, GBLT-VG reduce the management load by using a virtual group when a number of parties is small, thereby decreasing the existing managers?? loads dynamically. This paper also presents simulation results demonstrating how GBLT-VG can reduce the average number of users managed by the server.     

Laser-Sintered Barium Titanate

Laser sintering of alkoxy-derived ultrafine BaTiO₃ powders was investigated. The temperature increases of the sample with laser irradiation were measured with a thermocouple. It was found that laser irradiation could generate enough heat to sinter ceramics. A slurry was prepared by mixing an alkoxy-derived BaTiO₃ powder, binder additives, solvent, and plasticizer. The slurry was tape cast and dried to give a green sheet. The green sheet was laser sintered and was then characterized by SEM, XRD, and density measurements. The effect of burnout before laser irradiation and the characteristic microstructure of laser-sintered BaTiO₃ are described.     

Conductive Papers Containing Metallized Polyester Fibers for Electromagnetic Interference Shielding

Conductive papers were developed for preventing or reducing electromagnetic interference (EMI), and their shielding efficiency was evaluated. This type of conductive paper consists of wood pulp, synthetic pulp and metallized polyester fibers (0.5–2.0 mm long and 14 m in diameter) whose surfaces are coated with nickel alone (Ni-PET) or copper and nickel double layers (Ni-Cu-PET) by electroless plating. In this report, the effect of the characteristics of these metallized fibers, such as their conductivity, geometry and the concentration of fibers in paper, which lead to high efficiency for shielding effectiveness is discussed. For instance, one of the conductive papers (80 g/m2) which was prepared by mixing 40% Ni-Cu-PET and 60% synthetic polyethylene pulp showed over 40 dB shielding effectiveness between 10 MHz and 1 GHz.