Study of liquid injection impact on the performance of new refrigerant mixtures

In this paper, the test results of liquid injection impact on the performance of new alternative refrigerant mixtures such as: R-410A, R-507, R-407C and R-404A are discussed, analysed and presented. The test results were obtained using an air-source heat pump set-up with enhanced surface tubing under various liquid injection ratios. Performance tests were conducted according to the ARI/ASHRAE standards. The performance data demonstrated that as liquid injection ratio increases, compressor head pressure and discharge temperature decrease. This has a positive effect in protecting the compressor. The effect of liquid injection on mixture behaviour varies from one mixture to another depending upon the mixture's composition. Furthermore, liquid injection appears to have a significant influence on R-410A behaviour compared to the other mixtures in question. Copyright © 2002 John Wiley & Sons, Ltd.     

Characteristics of Milk Powders Produced by Spray Freeze Drying

Skim and whole milk powders were manufactured at lab scale by spray freeze drying (SFD), using liquid nitrogen as the cryogen. The polydispersity of droplet/particle sizes was limited using an encapsulator nozzle to atomize the feed. Particle morphology was examined using a scanning electron microscope. Samples were compared with equivalent spray-dried powders in tests of wettability and dissolution in water. The spray freeze-dried powders were found to be highly porous, with a uniform structure of pores throughout the entire particles. When tested in water, SFD skim milk powders wetted roughly three times as fast as industrially spray-dried agglomerated skim milk powders and were observed to dissolve rapidly by breaking down into smaller particles.     

Performance of a non‐load‐bearing steel stud gypsum board wall assembly: Experiments and modelling

A gypsum wall assembly was exposed to an intense real‐scale compartment fire. For the wall assembly, temperatures were measured at the exposed face, within the stud cavity, and at the unexposed face during the fire exposure. Total heat flux gauges were used to measure the temporal variation of the energy incident on the walls, and cameras, both visual and infrared, were used to image the unexposed face of the wall assembly during the fire exposure. The behaviour of the wall assembly under the fire load is discussed as are current model results for a simulation of the fire test. Copyright © 2006 John Wiley & Sons, Ltd.     

Minimal communication cost software construction in the Internet environment

This paper investigates the issue of building software in the Internet environment, where local area network (LAN) based systems are interconnected by links with different bandwidth and do not share file systems. The software is modeled as a directed acyclic graph. Each node in the graph represents a logical step in processing the software while the edges describe the order of execution. The problem is to construct the software at a particular LAN with minimum Internet communication cost. An optimal polynomial algorithm, SOFTCON, with time complexity is presented, where and are the number of nodes and edges in the graph describing the software respectively, is the number of LANs in the Internet environment, and is the time complexity of the network flow algorithm on the flow network with nodes and edges transformed from the directed acyclic graph of the software. Received: 6 December 1995 / 1 May 1996     

Surface-mediated effects on porous polymer monolith formation within capillaries

The formation of a porous polymer monolith (PPM) is influenced by the physico-chemical properties of the wall surface of its container. This influence can have a dramatic effect on the resulting monolith morphology depending on the nature and composition of the wall. Indeed, a dense polymer layer or “sheath”, distinct from the bulk porous material, has been observed at the wall surface of capillaries, and thus a study was undertaken to explore the dependence of this layer on the hydrophobicity of the surface. A range of silanizing reagents were used to modify the surface of the fused silica capillary, including aminopropyl, trimethylsilyl, octadecyl and perfluorooctyl functionalities. Crosslinked butyl acrylate-based PPM was formed in the modified capillaries and extruded. SEM images of the monoliths were used to examine the sheath morphology and thickness, which are discussed with respect to surface hydrophobicity.     

Shear mode coupling and tilted grain growth of A1N thin films in BAW resonators.

Polycrystalline A1N thin films were deposited by RF reactive magnetron sputtering on Pt(111)/Ti electrode films. The substrates were tilted by an angle ranging from 40 degrees to 70 degrees with respect to the target normal. A low deposition temperature and a high sputter gas pressure were found ideal for tilted growth. The resulting grain tilt angle amounts to about half the substrate tilt angle. For coupling evaluation, 5 GHz solidly mounted resonator structures have been realized. The tilted grain A1N films exhibited a permittivity in the 9.5-10.5 range and loss tangent of 0.3%. Two shear modes as well as the longitudinal mode could be clearly identified. The coupling coefficient k2(eff) of the fundamental thickness shear mode (TS0) was found to be about 0.5%, which is compatible with a c-axis tilt of about 6 degrees.     

Fluxing of a 359/SiC/10p composite with alkali chlorides: effect of inclusions

The effect of salt addition, in the form of a fluxing agent containing equivalent amounts of NaCl and KCl, on the microstructure and mechanical properties of 359/SiC/10p composite has been investigated. Both microstructure and properties are affected, with the removal of magnesium and strontium and the introduction of sodium and potassium being responsible for the degradation in properties. Thermodynamic calculations have been carried out to account for the effect of salt addition in terms of the surface adsorption of sodium and potassium impurities and the consequent changes in the surface-interface tension of their binary alloys. Mechanisms for the degradation of properties have been discussed.     

Relevance of the use of the quality index concept in cast SiCP-reinforced Al-Si-Mg composites

The quality index, Q, defined as Q=UTS + klogE1 was introduced as a means to better interpret tensile test data. However, its use in the case of composite materials is often questioned. The difficulty arises from the fact that the elongations obtained are usually close to, or less than, unity. Based on a heat-treatment study of cast Al-Si-Mg/SiC_p composites (359/SiC_p) and an analysis of the tensile properties obtained, it is shown that the concept of quality index, as it is commonly applied, is inappropriate in describing the combined effects of UTS and E1, and it is much better, instead, to use the probable yield strength (PYS) for such materials. Respective expressions for Q and PYS have been obtained for the 359, 359/SiC/10_p and 359/SiC/20_p alloys studied.     

Compound types and properties of Utah and Athabasca tar sand bitumens

Properties and compound types were examined in detail for tar-sand bitumens representative of four major deposits in Utah and Alberta. Methods for bitumen extraction, separation, and compound type (functional group) analysis are presented. Results of the analyses are compared with each other and with results in the literature for tar-sand bitumens and petroleum. Comparison of the results of Utah bitumens with the Athabasca bitumen provides a basis for evaluation of the Utah bitumens because considerable information about the processing characteristics of the Athabasca bitumen has been reported. Simulated distillation and Chromatographic separation data indicate that, in general, the tarsand bitumens most closely resemble Wilmington petroleum with respect to hydrocarbon/non-hydrocarbon distribution, especially in the non-distilling portion (the distillable portions, mainly hydrocarbons, are similar for all samples). Tar-sand bitumens were also shown to differ significantly from one another, principally in the amounts and kinds of heteroatomic compound types present. This information is important because of the effects that composition has on recovery and refining processes. Analyses of the chemical functionalities also provide a basis for developing correlations between bitumen composition and the recovery and processing characteristics of the bitumen.