高效液相色谱法同时测定化妆品中的7种香豆素

基于香豆素类化合物在化妆品中的使用情况及其对人体健康的危害,采用C18色谱柱作为分析柱,通过优化试验条件建立了一种可准确、简便测定化妆品中多种香豆素类化合物的高效液相色谱法。试验结果表明,7种香豆素类化合物的保留时间和峰面积的相对标准偏差分别小于0.1%和2%,且检出限均低于40μg/L;通过样品加标试验,得到7种目标化合物的回收率为80%~94%。所建立方法具有快速、简便、准确、灵敏的特点,是测定化妆品中多种香豆素类化合物的有效方法。     

Different hydrothermal corrosion results between two sides of sodalime float glass and the possible corrosion mechanism

Sodalime float (SF) glass is widely used in our societies and industries. Hydrothermal corrosion method is one of the effective ways to prepare a superhydrophobic glass, but there is still lack of knowledge about hydrothermal corrosion behavior and mechanism of SF glass. We have hydrothermally treated SF glass at 180 °C for different time, and tried to reveal the aqueous corrosion process of SF glass. We have characterized the morphologies and chemical compositions of samples, and found that (1) the two sides of SF glass have different corrosion resistances, and (2) a multilayer structural coating with a nanoflake layer (Mg-rich gel layer), a nanowire layer (Ca-rich gel layer), and a porous layer (etched layer) is formed on the air-side of SF glass. Based on the experimental results, we have proposed an aqueous corrosion mechanism of SF glass. The insights of the hydrothermal corrosion behaviors and mechanism provide helpful guidelines to glass surface structural control and functionalization.     

Effect of an abrupt change in pulling rate on microstructures of directionally solidified Al2O3-Er3Al5O12 eutectic and off-eutectic composite ceramics

Directionally solidified microstructures of Al₂O₃-Er₃Al₅O₁₂ eutectic and off-eutectic in situ composite ceramics were explored under abrupt-change pulling rate conditions. Corresponding temperature distributions and interface locations were studied. In eutectic composition, fluctuation of eutectic spacing occurred when the pulling rate increased abruptly. A gradually increase or abrupt increase in eutectic spacing was observed when the pulling rate decreased abruptly. In hypoeutectic and hypereutectic compositions, formation of the primary phases were suppressed when the pulling rate increased abruptly from 10?µm/s to 100?µm/s, while primary phases precipitated when the pulling rate decreased abruptly from 100?µm/s to 10?µm/s. The interface altitude decreased after the pulling rate increased abruptly, but increased after the pulling rate decreased abruptly. The liquid composition restriction (around the eutectic composition) at the eutectic interface plays an important role in the suppression of the primary dendrite and coupled eutectic oxides can be obtained in off-eutectic compositions even under higher solidification rate conditions.     

2A12铝合金化学铣切加工工艺探讨

为了精确加工2Al2铝合金,探讨了化铣时间和温度对其化铣速率及表面粗糙度的影响,采用现代技术对化铣工件的力学性能进行了测试与分析.结果表明:延长非化铣部位保护胶固化时间并使保护部位向非加工面位移3～5 mm可很好地解决未化铣区域的腐蚀问题;随化铣时间的延长,化铣速率降低,且化铣温度与化铣速率呈现正相关性;化铣表面的粗糙度随化铣时间的延长而增加,随化铣温度的升高呈先减小后增加的趋势;化铣后材料的抗拉强度和屈服强度均有所提高.     

Process monitoring method based on correlation variable classification and vine copula

Chemical processes are becoming increasingly complicated, leading to an increase in process variables and more complex relationships among them. The vine copula has a significant advantage in portraying the dependence of high-dimensional variables. However, as the dimensions increase, the vine copula model incurs a high computational load; such pressure greatly reduces model efficiency. Relationships among variables in the industrial process are complex. Different variables may be strongly or weakly associated or even independent. This paper proposes a process monitoring method based on correlation variable classification and vine copula. The weighted correlation measure is first used to divide variables into a correlated subspace and weakly correlated subspace. Then, two vine structures, C-vine and D-vine, are applied to the correlated and weakly correlated subspaces, respectively. This method takes advantage of C-vine for correlated variables and the flexibility of D-vine for weakly correlated variables. Finally, comprehensive statistics are established based on different subspaces. Monitoring results of the numerical system and the Tennessee Eastman process demonstrate the effectiveness and validity of the proposed method.     

Hydrogel photocatalysts for efficient energy conversion and environmental treatment

Photocatalysts have attracted great research interest owing to their excellent properties and potential for simultaneously addressing challenges related to energy needs and environmental pollution. Photocatalytic particles need to be in contact with their respective media to exhibit efficient photocatalytic performances. However, it is difficult to separate nanometer-sized photocatalytic materials from reaction media later, which may lead to secondary pollution and a poor recycling performance. Hydrogel photocatalysts with a three-dimensional (3D) network structures are promising support materials for photocatalysts based on features such as high specific surface areas and adsorption capacities and good environmental compatibility. In this review, hydrogel photocatalysts are classified into two different categories depending on their elemental composition and recent progresses in the methods for preparing hydrogel photocatalysts are summarized. Moreover, current applications of hydrogel photocatalysts in energy conversion and environmental remediation are reviewed. Furthermore, a comprehensive outlook and highlight future challenges in the development of hydrogel photocatalysts are presented.     

振冲碎石桩在海塘软基处理中的应用

利用振冲碎石桩处理软土地基,对地基具有置换、排水、加筋等作用,与原土基构成复合地基,可提高地基承载力。结合台州市海堤工程实例,对振冲碎石桩的技术工艺、设计、施工和检测等方面进行介绍。