动态评价技术在塔河碳酸盐岩缝洞型油气藏中的应用

塔河油田奥陶系油气藏是大型碳酸盐岩溶洞型油气藏，其储渗空间主要为大小不同的溶洞、裂缝带、溶蚀孔隙等组成，该油气藏具有极强的非均质性，单纯用静态资料来认识这类油气藏是非常困难。文章提出利用生产动态资料和信息进行该类型油气藏研究的新思路，利用人工神经网络技术在处理非线性相关参数预测方面的优势，并以渗流理论为基础，结合试井成果，选用已知油井的产量、油嘴、油压、含水率、气油比、原油密度等6个开发动态参数作为样品输入数据，推导出影响油气藏开发的重要参数（地层系数）与生产信息的关系，建立了人工神经网络预测储层参数的结构模型。通过塔里木盆地塔河油气田实例研究，说明了利用动态信息评价油气藏技术在碳酸盐岩缝洞型油气藏储层预测和非均质性分析等方面具有较高的实用价值。     

相关条件下基于N-P准则的分布式检测理论研究

本文针对并行网络、二元局部判决的情况,研究了在相关条件下基于N-P准则的分布式检测融合算法,给出了在联合概率密度已知和未知两种情况下的最优融合规则的理论推导及相应的解决方案,并在实验仿真的基础上,得到了部分有益的结论。     

TUD-DNS3脱硝助剂在催化裂化装置的工业应用

TUD-DNS3脱硝助剂在中韩（武汉）石油化工有限公司1号催化裂化装置上进行了工业应用。结果表明：针对两段再生工艺，当系统中助剂占总催化剂藏量的质量分数为2.6%时，烟气脱硫装置外排污水中的氨氮质量浓度由加剂前的100 mg/L下降至40 mg/L以内；助剂的加入降低了CO焚烧炉的炉膛温度，有利于烟气的合格排放，并对装置操作、产品分布及汽油、柴油产品质量无不良影响。     

热管传热性能对小型热管换热器散热效能影响

在零重力辅助下,小热管热阻是小型热管换热器散热效能的重要影响因素之一。基于集总参数法对于换热器系统数值计算的高效性思想,建立了热管、热管换热器的集总参数模型。对同一热管换热器选用不同传热性能的热管,在不同传热温差和流体质量流速下,就其散热效能进行了数值计算。计算结果表明,在零重力辅助下,热管换热器管内热阻存在一临界值Rcri。当热阻RHP≤Rcri时,管外热阻起主导作用,热管换热器的散热效能εh几乎不随热管管内热阻的值而变化。     

广钢转炉分厂2号方坯连铸机拉速问题的探讨

通过分析钢水在结晶器内凝固的不均匀性及对钢水结晶的热量平衡计算，讨论连铸中间包钢水温度、结晶器冷却水流量及进出水温差对拉坯速度的影响。     

不等波纹函数低通原型的理论及应用

本文提出不等波纹函数低通原型，并对其理论进行初步探讨。切比雪夫函数及最平坦型巴特活兹函数皆为其特例。文中给出不等波纹函数的几个性质，最后给出两个应用实例，消除耦合环自感部分的影响；抑制高次模的微带圆盘腔带通滤波器。     

长距离曲线顶管在杭州河坊街工程中的应用

对杭州市重点工程—杭州河坊街长距离曲线顶管进行了总结和介绍 ,可为同类工程借鉴和参考     

Effects of alloy additions on the microstructures and tensile properties of cast Co-Cr-Mo alloy used for surgical implants

The composition of the Co-Cr-Mo alloy has been modified by additions of nickel and some trace elements aluminium, titanium and boron. In this paper, the first part of the present study, the effects of alloy additions on the microstructures and tensile properties of the as-cast Co-Cr-Mo alloy are discussed. The effects of alloy additions on the fatigue behaviour of the alloy will be discussed in the second part of the present study. It is found that alloy additions do not seem to result in changes in the nature of the casting structure. A directional, coarse dendritic cast structure is produced in the modified alloys as in the base alloY. However, the alloy additions affect the carbide precipitations and the formation of some fine details of the microstructure such as dislocations, stacking faults and twins produced during the solidification. A considerable improvement in the transient mechanical properties, especially in the tensile ductility, is achieved by modifying the base alloy with alloy additions.     

Preparation of BaMgAl10O17∶Eu2+ and Its Phase Behavior in Microemulsion System

BaMgAl10O17∶Eu2 (BAM) was prepared in the microemulsion system and its phase behavior was studied. There exists a small region in the reverse microemulsion system where the dispersed particles are of spherical form. In this way, BAM blue phosphor with good dispersion can be synthesized. The microemulsion phase diagrams of the pseudo-ternary system (Triton X-100/cosurfactant-oil-BAM brine) were first established intuitively by the dilution method. The microstructure of microemulsions was determined through eyeballing, conductance technique, and polar optical microscopy. Its phase behavior is affected by various factors, such as temperature (room temperature, 30, 40 ℃), oil, surfactants, and cosurfactants in microemulsions. According to the phase diagrams, the microemulsion system of Triton X-100/1-hexanol-hexane-BAM brine was chosen to prepare the precursor. The BAM phosphor can be obtained via sintering the precursor at a comparatively low temperature. The phosphors were characterized by XRD and vacuum ultraviolet (VUV) spectra.