Room Temperature Ferromagnetism in Co-doped CuAlO2 Nanofibers Fabricated by Electrospinning

One-dimensional, diluted magnetic semiconductor nanofibers have attracted increasing attention for their unique magnetic properties, large specific surface area, and high porosity. These qualities lead to excellent performance in magneto-optical devices, magnetic resonance imaging, ferrofluids and magnetic separation. The purpose of this study is to fabricate P-type one dimensional CuAlO2-based diluted magnetic semiconductor nanofibers. First, we fabricated Cu Al0.95Co0.05O2 nanofibers with an average diameter of 1 μm with the electrospinning method. The annealed nanofibers were thermally treated at a temperature of 1 100 ℃ and then shrunk to a diameter of about 650 nm. We used X-ray diffraction measurements and Raman spectra to confirm that the Cu Al0.95Co0.05O2 nanofibers had a single impurity free delafossite phase. The X-ray photoelectron spectroscopy analysis indicates that Co was present in the +2 oxidation state, resulting in an room temperature ferromagnetism in the Cu Al0.95Co0.05O2 fiber. This contrasts with nonmagnetism in pristine CuAlO2 fiber. The coercivity(Hc) value of 65.26 Oe and approximate saturation magnetization(Ms) of 0.012 emu/g demonstrate good evidence of ferromagnetism at room temperature for Cu Al0.95Co0.05O2 nanofibers.     

Effect of Li2O on the crystallization behavior of CaO-Al2O3-SiO2-Li2O-Ce2O3 mold slags

The effect of Li₂O on the crystallization properties of CaO-Al₂O₃-SiO₂-Li₂O-Ce₂O₃ slags was investigated. With increasing the Li₂O content, LiAlO₂ and CaCeAlO₄ were the main crystalline phases. LiAlO₂ formed for the charge compensating of Li⁺ ions to [AlO₄^5?]-tetrahedrons, and CaCeAlO₄ formed as a result of the charge balance of Ce³⁺ ions, Ca²⁺ ions, and [AlO₆^9?]-octahedrons. Increasing the content of Li₂O to 10%, the crystallization temperature was the highest, and the incubation time was the shortest. The crystallization ability was strong due to the three factors of strengthening the interaction between ions and ion groups, decreasing the polymerization degree, and increasing the melting temperature. Further increasing the content of Li₂O, the crystallization performance was obviously suppressed, because the melting temperature and the force between the cations and the anion groups decreased.     

豫西雷门沟钼矿水文地质条件分析及涌水量预测

豫西熊耳山雷门沟钼矿床位于东秦岭多金属成矿带东段,是已探明的超大型斑岩型钼矿,前人研究程度高、地质成果丰硕,但对矿床开采技术条件方面研究较少。本次通过地质调查工程、水文地质试验等方法,从水文地质角度,对雷门沟钼矿床水文地质条件进行研究,填补了该方面的空白,丰富了研究成果；采用水文地质比拟法预测未来矿坑最大排水量2613 m³/d,经实践检验结果较为可靠；总结的采坑排水量预测方法、含水层特点、矿床充水因素以及防治水措施,以期对该区域水文地质工作具有参考价值。     

基于Isograph的FMECA分析在潜孔钻机中的应用

为提高潜孔钻机的可靠性,利用FMECA分析方法并结合Isograph软件对潜孔钻机进行FMECA分析。通过对潜孔钻机FMECA分析,确定了潜孔钻机危害性最高的组成结构,提出了预防维护的措施,为提高潜孔钻机的可靠性提供了依据。     

一种压力容器设计的优化方法

当压力容器内体积一定时,利用给出的内体积公式,在一定范围内改变壳体内径及筒体长度(筒体与两封头焊缝间距离),按照GB 150-1998《钢制压力容器》有关规定可得到壳体壁厚一定但内径和筒体长度不同时相应的壳体质量。根据壳体质量的大小并综合考虑其它因素,是选择最佳设计方案的有效途径。     

小型机载数字视频记录系统的设计与实现

采用嵌入式控制模块SOM2386和专用视频处理芯片SZ1510,设计和实现了一种基于电子硬盘存储的嵌入式小型机载数字视频记录系统。给出了系统总体方案,阐述了视音频解码编码、接口、控制及存储单元的硬件设计,介绍了系统的软件设计,并给出了系统软件的整体工作流程。该系统体积小、重量轻、抗震性好、使用维护方便,已在某型飞机上得到应用。     

井下煤仓全深度分段爆破成井技术

介绍了在煤矿现有设备条件下，全深度一次钻孔分段爆破掘进煤仓的设计与应用情况，论述了爆破方案确定，参数设计及主要措施，通过实践取得了良好效果。     

Microstructure-Property Correlation in AI_4C_3 Dispersion Strengthened Al Composite

The microstructure and tensile properties of Al_4C_3 dispersion strengthened Al composite fabricatedby reaction milling technique were investigated.It is indicated that the rod-like Al_4C_3 dispersoidshaving a diameter of 0.02-0.03 μm and a length of 0.1-0.3μm are formed by reaction of C with Al,and uniformly distributed in the Al matrix.The interface between Al_4C_3 and Al is clean and theinterfacial bonding is good.The matrix consists of the subgrains which have the size of 0.3-0.4μm,and most of the Al_4C_3 dispersoids are distributed on the subgrain boundaries.The 11 vol.-%Al_4C_3/Al composite exhibits an UTS (ultimate tensile strength) of 400 MPa and anelongation-to-failure of 8.0%.     

生物分解性纤维及其应用

本文介绍了生物分解性纤维所用的树脂，生产方法及应用。