Breakdown characteristics of oil and paper insulation for a very fast transient voltage

This paper describes the dielectric breakdown characteristics of oil and oil‐impregnated paper for very fast transient (VFT) voltages. Blumlein circuits generate VFT voltages of 60 and 300 ns in a pulse width that simulates disconnecting switching surges in gas‐insulated switch gears. We measured the breakdown voltages of needle‐to‐plane, plane‐to‐plane oil gaps and several pieces of paper between plane electrodes for VFT and lightning impulse voltages. The measured data were formulated in V‐t characteristics and Weibull probability distributions. The inclination n of V‐t characteristics of insulating paper is 150, which is less than n = 13.7 of the plane‐to‐plane oil gap in the VFT time range. The shape parameters of Weibull distribution obtained in this study show that the scattering of breakdown voltages of paper is much less than that of oil. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(4): 16–24, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10043     

A Fuzzy Expert System for Damage Assessment Using Genetic Algorithms and Neural Networks

Abstract: An efficient knowledge-acquisition support method is required for improvement and maintenance of the knowledge base in durability evaluation of an RC bridge deck. Such a method is proposed in this paper to automatically acquire fuzzy production rules. This method makes joint use of genetic algorithms and a neural network. Using a neural network as a subsystem, the evaluation function of genetic algorithms can be provided with the weights of the neural network. Introducing a neural network into genetic algorithms, it is possible to acquire new knowledge so that the method is useful when it is difficult to acquire knowledge in the field.     

Accumulation of amplified target DNAs using thiol/biotin labeling, S1 nuclease, and ferrocene-streptavidin-magnetic system and a direct detection of specific DNA signals with screen printed gold electrode

Combinations of PCR-based amplification platform using 5′ thiolated and biotinylated specific primers, S1 nuclease-PCR products treatment, ferrocene-streptavidin (Fc-Stv)-magnetic binding for DNA accumulation, and screen printed gold electrode for the DNA allocation, were applied to Hoechst 33258-induced DNA aggregation and signals induction system for direct signals detection and DNA quantification in food samples. Thiolated and biotinylated at each 5′ terminus enabled DNA purification through S1 nuclease treatment for primers and non-specific DNA elimination and enabled DNA trapping with a ferrocene-streptavidin-magnetic system. This facilitated the accumulation of target DNAs at higher concentration, resulting in enhanced signals. After allocation of DNA on the surface of gold electrode via thiol binding, intensity of DNA signals through these treatments could be measured directly after being induced by Hoechst 33258. Wider amplitude changes in anodic current peaks between negative and positive samples (increasing from 3.70 to 10.10 μA) compared with those applied with no treatment combinations (decreasing from 3.92 to 1.23 μA) were observed. This enhancement of the signals allowed a greater efficiency of DNA quantification. When this combination was used for GMOs content estimation in reference samples, results revealed an improved accuracy from 66% to 96%. The combined biosensor system, although more costly than the standard Hoechst 33258/carbon electrode system, provided an alternative choice for DNA quantification, offering labor-free immobilization of probe onto electrode surface, easy test administration, and efficient semi-quantitative test without expensive instruments.     

Non-linear current–voltage characteristics related to native defects in SrTiO3 and ZnO bicrystals

SrTiO₃ and ZnO bicrystals with various types of boundaries were fabricated in order to examine their current–voltage characteristics across single grain boundaries. Their grain boundary structures were also investigated by high-resolution transmission electron microscopy. In Nb-doped SrTiO₃, electron transport behaviors depend on the type of boundaries. Random type boundaries exhibit highly non-linear current–voltage characteristics, while low angle boundaries show a slight non-linearity. On the contrary, undoped ZnO does not exhibit non-linear current–voltage characteristics in any type of boundaries including random ones. It is suggested that the differences observed in current–voltage properties between the two systems are mainly due to the difference in the accumulation behavior of acceptor-like native defects at grain boundaries. A clear non-linearity is obtained by means of Co-doping even for the highly coherent Σ1 boundary in a ZnO bicrystal. This is considered to result from the production of acceptor-like native defects by Co-doping.     

Yttria Doping and Sintering of Submicrometer-Grained α-Alumina

The sintering behavior of α-alumina powders doped with magnesia (500 or 1500 ppm) and yttria (0, 500, or 1500 ppm) was investigated using constant-heating-rate dilato-metric experiments. The apparent activation energies for the intermediate stage of sintering were 740, 800, and 870 kJ/mol for 0, 500, and 1500 ppm yttria doping levels, respectively; these were independent of magnesia doping. Yttria-doped powder compacts exhibited systematic anomalous second peaks in the densification rate curves at certain grain sizes which were determined only by yttria doping levels. Before the anomalous peak, with lower yttrium contents at grain boundaries, yttrium in an atomic state delays densification and raises the apparent activation energy. Beyond the peak, with higher yttrium contents at grain boundaries, yttria-rich precipitation delays the densification. Within the peak, yttrium segregation near the saturation level enhances densification.     

Mechanical properties of sinter-forged Al2O3-ZrO2 ceramics

Two kinds of composites, Al₂O₃-25 wt% ZrO₂(2 mol% Y₂O₃) (Y-ZTA), Al₂O₃-25 wt% ZrO₂(8 mol% CeO₂) (Ce-ZTA) were produced by the sinter-forging process. The effect of presintering temperature on the mechanical properties of the composites was examined. The sinter-forging process increased the room-temperature bending strength in comparison with pressureless sintering, owing to the smaller grain size in sinter-forged bodies than in pressureless sintered ones. It was found necessary to keep the presintering temperature considerably lower than sinter-forging temperature in order to improve the room-temperature strength. The strength of sinter-forged Ce-ZTA was higher than that of sinter-forged Y-ZTA. The residual surface compressive stress induced by the phase transition during grinding in Ce-ZTA was found to be effective to further improve the strength and fracture toughness.     

Channelling studies on the lattice location of B atoms in graphite

In order to obtain information on the lattice location of B atoms in graphite, channelling experiments have been performed at room temperature with a proton beam of an energy of 0.65-0.77 MeV for the 〈0 0 0 1〉 axial channel in highly oriented pyrolytic graphite (HOPG) crystals doped with 0.32 at.% B. The B atoms are detected by measuring α-particles which are emitted as a result of a nuclear reaction ¹¹B(p,α)αα. It is clearly demonstrated that most of B atoms are shadowed behind the 〈0 0 0 1〉 C atomic rows. Taking account of the already reported experimental results on a change of lattice parameters by B-doping, it is concluded that most of B atoms are located at substitutional sites. It is also observed that B-doping introduces lattice strain on the c-plane. In addition, the presence of a small portion of interstitial B atoms is suggested.     

TRVs and fault clearing stresses in extra-high-voltage radial networks

To cope with the high rate of increase of power demand in the main industrialized districts in Japan, 550-kV transmission systems covering the districts have been reinforced, with most of the main power plants connected directly to these systems. Through 550-/300-kV substations, the majority of power to the districts is supplied by 300-kV systems. To limit the excess short-circuit capacity in the 300-kV systems, they tend to be reconstructed as so-called radial networks. In radial networks with high short-circuit capacity and relatively small number of transmission lines connected to the substation busbars, the rate of rise of TRV can be far higher than standard value. This paper analyzes the transient recovery voltages (TRV) in such extra-high-voltage radial networks in Japan, together with the relevant stresses to circuit-breakers during fault clearings. Future system conditions have also been introduced. As the typical rate of rise of the TRV values, more than twice that of today's standard ones are probable.     

Surgical navigation by autostereoscopic image overlay of integral videography

This paper describes an autostereoscopic image overlay technique that is integrated into a surgical navigation system to superimpose a real three-dimensional (3-D) image onto the patient via a half-silvered mirror. The images are created by employing a modified version of integral videography (IV), which is an animated extension of integral photography. IV records and reproduces 3-D images using a microconvex lens array and flat display; it can display geometrically accurate 3-D autostereoscopic images and reproduce motion parallax without the need for special devices. The use of semitransparent display devices makes it appear that the 3-D image is inside the patient's body. This is the first report of applying an autostereoscopic display with an image overlay system in surgical navigation. Experiments demonstrated that the fast IV rendering technique and patient-image registration method produce an average registration accuracy of 1.13 mm. Experiments using a target in phantom agar showed that the system can guide a needle toward a target with an average error of 2.6 mm. Improvement in the quality of the IV display will make this system practical and its use will increase surgical accuracy and reduce invasiveness.