Diffusion Bonded EDM Electrode with Micro Holes for Jetting Dielectric Liquid

This paper describes improvement of machining characteristics of electrical discharge machining of deep slots using a tool electrode which has micro holes for jetting dielectric liquid over the working surface. The tool electrode was made by the diffusion bonding of two copper plates, over an interface on which micro grooves for jetting the dielectric fluid were formed using electrolyte jet machining. In conventional machining, it is difficult to drill micro holes at the end of a slim electrode and circulate the dielectric fluid from the other end. Hence a solid tool electrode is used and periodically lifted up during machining to flush debris particles out of the discharge gap. Use of the newly developed tool electrode was found to shorten the processing time and improve machining accuracy significantly compared with the conventional solid tool electrode. Since the holes are micro, the outlet shapes are not replicated onto the bottom surface of the slot machined.     

Continual conversion of free fatty acid in rice bran oil to triacylglycerol by immobilized lipase

Rice bran oil containing 30–50% free fatty acid was continually converted to an oil containing more than 75% of triacylglycerol (TG) by means of immobilized lipase. The reaction was carried out at 60°C for 24 h with dehydration and reactant mixing by dry nitrogen flow under a positive nitrogen atmosphere. Enzymatic TG synthesis with evaporation by heating was not suitable because of the increasing peroxide value of the oil. Part of this article was presented at the annual meeting of the Japan Oil Chemists' Society at Sendai, Japan, October, 16, 1990.     

Characterization of the Advanced Satellite for Cosmology and Astrophysics x-ray telescope: preflight calibration and ray tracing

The x-ray properties of multinested thin-foil mirror x-ray telescopes (XRT's) on board ASCA, the Advanced Satellite for Cosmology and Astrophysics, were fully evaluated with an x-ray pencil beam.Scanning over the telescope aperture of 35 cm in diameter with an x-ray pencil beam, we found the effective area of a set of XRT's to be 325, 200, and 113 cm(2) at energies of 1.5, 4.5, and 8.0 keV, respectively. We derive the point-spread functions (PSF's) of the XRT's by measuring the image profile at the focal plane with an x-ray CCD. The PSF is found to exhibit a sharp core concentrated within 30 arcsec and a broad wing extended to 3 arcmin in half-power diameter. We also evaluate the contribution of stray light, which is caused by the single reflection of x rays by primary or secondary mirrors and by the backside reflection of the mirrors. To obtain the characteristics of the XRT in the energy region of 0.5-10.0 keV, incorporated with the measurements at discrete energies, we develop a ray-tracing method with the telescope design parameter, the PSF, and optical constants. In particular, we obtain the optical constants around the gold-atom M shell (Au-M) absorption-edge energies by measuring the reflectivity of our mirror sample, with monochromatized x-rays in the energy range of 2.0-3.5 keV from synchrotron radiation. Taking into account the PSF's and optical constants, we find that our ray-tracing program can reproduce all these XRT performances.     

A scalable interest-oriented peer-to-peer pub/sub network

There has been a big challenge in structured peer-to-peer overlay network research area. Generally, a structured overlay network involves nodes evenly or based on their resource availabilities, and gathers nodes?? resources to achieve some bigger tasks. The challenge here is to gather resources based on nodes?? interests, and only interested nodes are involved in a certain task. Toward this challenge, we propose a new scheme to a peer-to-peer publish/subscribe network. Publish/subscribe represents a new paradigm for distributed content delivery. It provides an alternative to address-based communication due to its ability to decouple communication between the source and the destination. We propose a Bloom filter based mapping scheme to map IDs to nodes?? interests in addition to new interest proximity metric to forward events and to build nodes?? routing tables. We also propose a new approach called ??shared interest approach?? for network discovery. To evaluate the algorithms proposed in this work, we conducted simulations in both static and dynamic settings, and found a low false positive rate. We also discuss about a well-known application called Twitter, and show how our scheme would work in a real environment.     

Application of multiple sensory evaluations to produce fermented beverages made from sole whey using Kluyveromyces marxianus

Various fermented whey-based beverages have been developed to reduce waste. However, approaches to increase the preference of whey-based beverages are required because of the low sensory acceptability of whey. Here, we identified the better starting material (whey type), between raw whey (RW) and demineralised whey (DMW), and determined the optimal initial concentration using multiple sensory evaluations to develop acceptable fermented beverages made from sole whey with pure cultured Kluyveromyces marxianus (i.e. without additional ingredients and processing methods). Acceptance tests showed that fermented beverages made from DMW were superior to RW as the starting material. The amounts of ethanol produced were 5.0%, 7.6% and 9.5% v/v from the different initial DMW concentrations of 10%, 15% and 20% w/v, respectively. We observed a significant positive correlation (r_s = 0.32, P < 0.05) between the assessment attributes, strength of taste as alcohol beverage and overall acceptability, indicating that higher concentrations of DMW yielded a more desirable product.     

Production and performance of the inFOCmicroS 20-40-keV graded multilayer mirror

The International Focusing Optics Collaboration for microCrab Sensitivity (InFOCmicroS) balloonborne hard x-ray telescope incorporates graded Pt/C multilayers replicated onto segmented Al foils to obtain the significant effective area at energies previously inaccessible to x-ray optics. Reflectivity measurements of individual foils demonstrate our capability to produce a mass quantity of multilayered foils with a rms roughness of 0.5 nm. The effective area of the completed mirror is 78 and 22 cm2 at 20 and 40 keV, respectively. The measured half-power diameter is 2.0 +/- 0.6 are min (90% confidence). The successful completion of this mirror demonstrates its applicability to future x-ray telescopes such as Constellation-X.     

A novel anionic surfactant templating route for synthesizing mesoporous silica with unique structure

Anionic surfactants are used in greater volume than any other surfactants because of their highly potent detergency and low cost of manufacture. However, they have not been used as templates for synthesizing mesoporous silica. Here we show a templating route for preparing mesoporous silicas based on self-assembly of anionic surfactants and inorganic precursors. We use aminosilane or quaternized aminosilane as co-structure-directing agent (CSDA), which is different from previous pathways. The alkoxysilane site of CSDA is co-condensed with inorganic precursors; the ammonium site of CSDA, attached to silicon atoms incorporated into the wall, electrostatically interacts with the anionic surfactants to produce well-ordered anionic-surfactant-templated mesoporous silicas (AMS). These have new structures with periodic modulations as well as two-dimensional hexagonal and lamellar phases. The periodic modulations may be caused by the coexistence of micelles that differ in size or curvature, possibly owing to local chirality. These mesoporous silicas provide a new family of mesoporous materials as well as shedding light on the structural behaviour of anionic surfactants.     

Analysis of electromagnetic force in wire-EDM

This paper clarifies the mechanism of how electromagnetic force applied to the wire electrode in wire electrical discharge machining (wire-EDM) is generated. This electromagnetic force is caused not only by DC component but also by AC components of the discharge current supplied to the wire. We therefore developed and used a two-dimensional finite element method (FEM) program to analyze the electromagnetic field taking into account electromagnetic induction. Assuming that trapezoidal pulse current is supplied to the wire, distributions of the current density and magnetic flux density were analyzed and changes in the electromagnetic force applied to the wire were calculated. Wire movement when the electromagnetic force alone was applied to the wire was also calculated. The calculated wire movement agreed with the measured wire movement when pulse current actually used in WEDM was supplied to the wire, clarifying the mechanism of electromagnetic force generation.     

Group feature extraction based on matrix factorization from long-range office-logging data

To increase the productivity of knowledge workers, it is necessary to manage their organization so that they are motivated to collaborate with each other for their synergy. However, it is difficult for managers to grasp the explicit interactions of workers in the organization all the time. Owing to advanced communications technology, and the reduced size and improved capabilities of computers, we are able to record group behaviors as logging data in the office. The aim of this study is to extract features of group behavior from long-range office-logging data. We apply principal component analysis to the data matrix whose element is the mean travel velocity calculated from an individual’s trajectory per day. The results demonstrate the feasibility of our approach, since nontrivial informative group features can be extracted.     

Evaluation of three-dimensional effects in short deep beams using a rigid-body-spring-model

Three-dimensional (3-D) effects in short deep beams without stirrups that failed in shear were investigated experimentally and analytically. Two deep beams with a shear span to depth ratio (a/d) of 0.5 and with different beam widths were tested. The effect of beam width on load-carrying capacity, failure mode, crack pattern and 3-D behavior was investigated, and shape effect due to beam width was clarified. In addition, the beams were analyzed by the 3-D rigid-body-spring model (RBSM). RBSM is a discrete form of modeling that presents realistic behavior from cracking to failure, and 3-D RBSM is applicable to simulate 3-D behavior as well as the confinement effect of concrete. Analytical results in terms of load–displacement curves and crack pattern are compared with the experimental results. Three-dimensional deformations, strut widths and cross-sectional stress distribution are investigated analytically and compared with the experimental results to determine 3-D behavior in detail. The 3-D effects in short deep beams are clarified.