Polarization losses in reflector antennas

Various definitions for polarization-loss efficiency of Cassegrainian and front-fed reflectors are compared. The effects of flare angle, feed taper and the feed pattern asymmetry on the polarization-loss efficiency are investigated. The definitions based on aperture fields are shown to be inadequate and far fields must be used for calculating the polarization losses.     

Fabrication of co-PVDF/modacrylic/SiO2 nanofibrous membrane: Composite separator for safe and high performance lithium-ion batteries

Highly porous free-standing co-poly(vinylidene fluoride)/modacrylic/SiO₂ nanofibrous membrane was developed using electrically-assisted solution blow spinning method. The performance and the potential of the membrane as a lithium-ion battery separator were investigated. The addition of modacrylic enhanced the solution spinnability that resulted in defect-free membranes. Moreover, the presence of modacrylic enhanced the dimensional and thermal stabilities, while the addition of hydrophilic SiO₂ nanoparticle enhanced both mechanical property and ionic conductivity. Combustion test results illustrated that the presence of modacrylic provide flame retarding property over a set of different polymeric-based membranes. Electrochemical performance results showed that the developed membrane can increase the battery capacity compared with the commercial separator.     

Hilbert-Huang Transform Analysis of Dynamic and Earthquake Motion Recordings

This study examines the rationale of Hilbert-Huang transform (HHT) for analyzing dynamic and earthquake motion recordings in studies of seismology and engineering. In particular, this paper first provides the fundamentals of the HHT method, which consist of the empirical mode decomposition (EMD) and the Hilbert spectral analysis. It then uses the HHT to analyze recordings of hypothetical and real wave motion, the results of which are compared with the results obtained by the Fourier data processing technique. The analysis of the two recordings indicates that the HHT method is able to extract some motion characteristics useful in studies of seismology and engineering, which might not be exposed effectively and efficiently by Fourier data processing technique. Specifically, the study indicates that the decomposed components in EMD of HHT, namely, the intrinsic mode function (IMF) components, contain observable, physical information inherent to the original data. It also shows that the grouped IMF components, namely, the EMD-based low- and high-frequency components, can faithfully capture low-frequency pulse-like as well as high-frequency wave signals. Finally, the study illustrates that the HHT-based Hilbert spectra are able to reveal the temporal-frequency energy distribution for motion recordings precisely and clearly.     

Synthesis and proton conductivity studies of 5‐aminotetrazole‐doped sulfonated polymer electrolyte membranes

This work reports the preparation and characterization of a new anhydrous proton conducting membrane based on poly(vinyl alcohol) (PVA), sulfosuccinic acid (SSA), and 5‐aminotetrazole (ATet) at various stoichiometric ratios. The proton conductivities of membranes were investigated as a function of ATet composition, SSA composition, and temperature. New anhydrous proton conducting membranes were characterized by infrared spectra, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), methanol permeability, and impedance measurements for proton conductivity. TGA showed that the samples were thermally stable up to 150°C. DSC results illustrated the homogeneity of the materials. Mechanical analysis showed that the storage modulus of the PVA–SSA–ATet blend polymer membranes decreased with increasing ATet content. The membranes with higher tetrazole content, or higher acid doping level presented the higher proton conductivity. PVA–SSA–ATet4 can exhibit an anhydrous proton conductivity of 1.7 × 10⁻³ S/cm at 130°C and the proton conductivity increased with increasing temperature and acid doping level. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Co-Fe films: effect of Fe content on their properties

The characterizations of Co-Fe films electrodeposited on Ti substrates under potentiostatic conditions were investigated as a function of the Fe content in the films. The compositional analysis was carried out by energy dispersive X-ray spectroscopy. Scanning electron microscopy used to analyze the surface morphology of the films revealed that the film surface became rather smooth with the increase of the Fe contents. X-ray diffraction patterns showed that the crystal structure changed depending on the Co:Fe ratio in the films. It was observed that the crystal structure converted from the predominant face-centered-cubic to the body-centered-cubic with increasing Fe content. All films showed anisotropic magnetic resistance, but their magnitudes decrease as the Fe content increases. Magnetic data obtained from by vibrating sample magnetometer revealed that the changes observed in the saturation magnetization and coercivity values may arise from the Fe content of the films. The different magnetic and magnetotransport properties may come from the structural differences caused by the Fe content.     

The effect of Fe content in electrodeposited CoFe/Cu multilayers on structural, magnetic and magnetoresistance characterizations

A series of CoFe/Cu multilayers were electrodeposited on Ti substrates from the electrolytes containing their metal ion under potentiostatic control, but the Fe concentration in the electrolytes was changed from 0.0125 M to 0.2 M. The deposition was carried out in a three-electrode cell at room temperature. The deposition of Cu layers was made at a cathode potential of -0.3 V with respect to saturated calomel electrode (SCE), while the ferromagnetic CoFe layers were deposited at -1.5 V versus SCE. The structural studies by X-ray diffraction revealed that the multilayers have face-centered-cubic structure. The magnetic characteristics of the films were investigated using a vibrating sample magnetometer and their easy-axis was found to be in film plane. Magnetoresistance measurements were carried out using the Van der Pauw method at room temperature with magnetic fields up to +/- 12 kOe. All multilayers exhibited giant magnetoresistance (GMR) and the GMR values up to 8% were obtained.     

Fabrication and characterization of silica modified polyimide–zeolite mixed matrix membranes for gas separation properties

In this study, new monomers having silica groups were synthesized as an intermediate for the preparation of poly(imide siloxane)-zeolite 4A and 13X mixed matrix membranes (MMMs). The effects of membrane preparation steps, zeolite loading, precursor’s composition, and pore size of zeolite on the gas separation performance of these mixed matrix membranes were studied. The new diamine monomer was prepared from 3,5-diaminobenzoic acid (3,5-DABA), 3-aminopropyltrimethoxysilane (3-APTMS), and zeolite 4A and zeolite 13X in N-methyl-2-pyrollidone (NMP) at 180 °C. Poly(imide siloxane)-zeolite 4A and 13X MMMs were synthesized from pyromellitic dianhydride (PMDA) and 4,4-oxydianiline (ODA) in NMP using a two-step thermal imidization. SEM images of the MMMs show the interface between polymer and zeolite phases getting closer when surface modified zeolite is used. The increase in glass transition temperature (T _g) confirms the polymer chain becoming more rigid induced by the presence of zeolite. The experimental results indicated that a higher zeolite loading resulted in a decrease in gas permeability and an increase in gas pair selectivity. In terms of O₂ and N₂ permeance and ideal selectivity, the separation performances of poly(imide siloxane)-zeolite MMMs were related to the zeolite type and zeolite pore dimension.