Effects of surface roughness of substrates on the c-axis preferred orientation of ZnO films deposited by r.f. magnetron sputtering

The c-axis preferred orientation of ZnO film is the most important factor for its successful application in piezoelectric devices. The effects of surface roughness of the substrate on the c-axis preferred orientation of ZnO thin films, deposited by radio frequency magnetron sputtering, were investigated. During sputtering, the oxygen content in the argon environment used was varied from 0 to 70% at a total sputtering pressure of 10 mTorr. Very smooth Si, smooth evaporated Au/Si, smooth evaporated-Al/Si, and rough sputtered-Al/Si were used as substrates. Their r.m.s. roughnesses, as measured by atomic force microscopy, were 1.27, 17.1, 21.1 and 65-118 Å, respectively. The crystalline structure and the angular spread of the (0 0* 2) plane normal to the ZnO films were determined using X-ray diffraction and X-ray rocking curves, respectively. The crystallinity and the preferred c-axis orientation of the ZnO films were strongly dependent on the surface roughness of the substrates rather than on the oxygen content of the working environment or on the chemical nature of the substrate.     

Structural changes of PVC plastisols in progress of gelation and fusion as investigated with temperature-dependent viscoelasticity,morphology, and light scattering

The structural changes of poly(vinyl chloride) (PVC) plastisols during mixing of PVC with a plasticizer was investigated; as the temperature was increased, the system was found to transform from a suspension of solid particles in a liquid medium to a swollen gel and ultimately to a fused homogeneous matrix. The dynamic viscoelastic measurements were utilized to continuously monitor the changes of moduli under a controlled heating rate, employing a mechanical spectrometer. Characteristic changes in the viscoelastic behavior were associated with changes in particulate morphology as observed with a scanning electron microscope (SEM). Both viscoelastic and morphological observations were shown to provide details of structural changes in conjunction with the behavior of the PVC–plasticizer interaction, enabling a qualitative discrimination of the gelation and fusion processes. An in situ small-angle light-scattering (SALS) method was performed to make a quantitative estimate for the swollen particles of PVC while they were in the progress of gelation and fusion. From the manner of increase in correlation distances, along with the changes in viscoelastic moduli and morphology, the swelling behavior of the particulate structures were examined on the quantitative basis and brief insight into the complex behavior of the PVC–plasticizer interaction began to be unfolded. © 1995 John Wiley & Sons, Inc.     

A precision on-line model for the prediction of roll force and roll power in hot-strip rolling

Investigated via a series of finite-element (FE) process simulations is the effect of diverse process variables on some selected nondimensional parameters characterizing the thermomechanical behavior of the strip in hot-strip rolling. Then, on the basis of these parameters an on-line model is derived for the precise prediction of roll force and roll power. The prediction accuracy of the proposed model is examined through comparison with predictions from a FE process model and also with measurements.     

Foveation-Based Error Resilience and Unequal Error Protection over Mobile Networks

By exploiting new human-machine interface techniques, such as visual eyetrackers, it should be possible to develop more efficient visual multimedia services associated with low bandwidth, dynamic channel adaptation and robust visual data transmission. In this paper, we introduce foveation-based error resilience and unequal error protection techniques over highly error-prone mobile networks. Each frame is spatially divided into foveated and background layers according to perceptual importance. Perceptual importance is determined either through an eye tracker or by manually selecting a region of interest. We attempt to improve reconstructed visual quality by maintaining the high visual source throughput of the foveated layer using foveation-based error resilience and error correction using a combination of turbo codes and ARQ (automatic reQuest). In order to alleviate the degradation of visual quality, a foveation based bitstream partitioning is developed. In an effort to increase the source throughput of the foveated layer, we develop unequal delay-constrained ARQ (automatic reQuest) and rate compatible punctured turbo codes where the punctual pattern of RCPC (rate compatible punctured convolutional) codes in H.223 Annex C is used. In the simulation, the visual quality is significantly increased in the area of interest using foveation-based error resilience and unequal error protection; (as much as 3 dB FPSNR (foveal peak signal to noise ratio) improvement) at 40% packet error rate. Over real-fading statistics measured in the downtown area of Austin, Texas, the visual quality is increased up to 1.5 dB in PSNR and 1.8 dB in FPSNR at a channel SNR of 5 dB.     

At least N+1 finite transmission zeros using frequency-variant negative source-load coupling

A second-order cross-coupled combline filter which has three finite transmission zeros is presented. The problem of the frequency-invariant coupling in a real circuit is introduced. To make extra transmission zeros, a top metalized dielectric block is used.     

Bandwidth and region division for broadband multi-cell networks

A cell planning technique termed BRD (bandwidth and region division) is presented for overcoming interference, maintaining QoS (quality of service) and improving channel capacity over OFDM (orthogonal frequency division multiplexing)-based broadband cellular networks. Through an optimal combination of sectorization and zero padding, bandwidth and region division is achieved that minimizes the outage probability for forward-link cell planning. In order to verify the effectiveness of the proposed algorithm, a Monte Carlo simulation is performed over multi-cell environments.     

Energy release rates of crack kinking by boundary condition sensitivity analysis

The energy release rate, which is the total derivative of the energy with respect to crack length, is recognized as corresponding to the shape sensitivity analysis with the crack length change represented by the tangential component of design velocity. In this paper the sensitivity formula recently developed for a changing boundary condition has been further extended to cover crack kinking under mixed mode loading. Due to difficulty in defining the velocity field at the corner, the energy release rate at the onset of crack kinking is obtained by extrapolating the energy release rates for finite length kinked cracks. A rectangular plate with a single edge slant crack under uniform tension is taken as a numerical example. The multi-region technique in the numerical implementation of the boundary integral equation is adopted to consider the asymmetry of the problem. Excellent accuracy is observed as compared with reference analytic solutions.     

Casein Hydrolysate Fractions Act as Emulsifiers in Process Cheese

ABSTRACT: Degrees of hydrolysis and emulsifying activity of casein hydrolysates were the highest at 4 h hydrolysis. The oil-off values of the mixture of hydrolysate (H) or supernatant (S) and traditional emulsifier (T) were not significantly different from the control made with traditional emulsifier, except for S + T = 3:1. Two other samples made with hydrolysate or supernatant only (H or S) showed higher oil-off value than the others (p < 0.05). In flavor property, no difference was found between samples made with traditional emulsifier and those made with the mixture of hydrolysate or supernatant at the ratio of 3 to 1. Therefore, these results indicated that a mixture of the hydrolysate or supernatant and traditional emulsifier might replace a traditional emulsifier in process cheese manufacturing.     

Parametric Instability Boundaries for Spatial Subharmonics in Photorefractive Moving Gratings: Theory and Experiments

We have derived a nonlinear spatiotemporal differential equation for spacecharge fields from Kukhtarev's material equations in a moving coordinate system and obtained the spatial subharmonic instability boundaries by using linear stability analysis. It is also found that there is an analogy between the temporal subharmonic and the spatial subharmonc instabilities in the sense that the governing differential equations describing the instability boundaries are formally identical. The experiments for generating spatial subharmonic waves are performed in a photorefractive Bi₁₂SiO₂₀ crystal by using conventional moving grating technique. The threshold detunings are experimentally determined and the results are compared with the theory.