Chromium evaporation and oxidation characteristics of alumina-forming austenitic stainless steels for balance of plant applications in solid oxide fuel cells

The chromium (Cr) evaporation behavior of several different types of iron (Fe)-based AFA alloys and benchmark Cr₂O₃-forming Fe-based 310 and Ni-based 625 alloys was investigated for 500 h exposures at 800 °C to 900 °C in air with 10% H₂O. The Cr evaporation rates from alumina-forming austenitic (AFA) alloys were ~5 to 35 times lower than that of the Cr₂O₃-forming alloys depending on alloy and temperature. The Cr evaporation behavior was correlated with extensive characterization of the chemistry and microstructure of the oxide scales, which also revealed a degree of quartz tube Si contamination during the test. Long-term oxidation kinetics were also assessed at 800 to 1000 °C for up to 10,000 h in air with 10% H₂O to provide further guidance for SOFC BOP component alloy selection.     

Un nouveau regard sur la société virtuelle

The importance of rigorous research into the actual impact of the new Information and Communication Technologies (icts) on society in general cannot be overemphasised. The answer to questions concerning the precise effect ofiCTs on interpersonal relations, communication, social inclusion and exclusion, trust and identity are now central to discussion in both commercial and business fora. This paper examines the concept of the “virtual society“ in the light of the findings of the ESRC (Economic and Social Research Council) Virtual Society? Programme (1997–2002). The paper describes the need to rethink the actual approaches used in researching this area of social science at the same time as performing the analyses themselves. The author also highlights the requirement for future research to examine actual on the ground experiences. How are new technologies actually used and by whom? In addition, the author utilises his overview of this large body of research to put forward a useful guide for predicting the use of ICTs in practice. These “5 rules of virtuality” serve as pointers to the experiences that may be encountered in the development and implementation of new technologies.     

WiMedia UWB 技术追踪

采用WiMedia UWB标准的越来越多 WiMedia通用无线电平台是实现传输速率高达480Mb／s（更高的传输速率正在开发中）无线个人局域网（WPAN）的基础。这个平台并不局限于某一类应用，而是允许同时存在不同的协议适配层，如图1所示。WiMedia规范既规定了一些如无线USB之间相互通信的应用，也规定其他不相互通信的接口同时存在的应用。     

Cryptosporidium Log-inactivation with Ozone Using Effluent CT10, Geometric Mean CT10, Extended Integrated CT10 and Extended CSTR Calculations

The draft Long-Term 2 Enhanced Surface Water Treatment Rule (LT2ESWTR) contains Cryptosporidium log-inactivation CT tables (ozone-in-water concentration [residual], “C” times contact time, T). Depending on water temperature, Cryptosporidium CT values that are listed are 15 to 25 times greater than CT values for equivalent Giardia log-inactivation credit. The elevated operating dose required for Cryptosporidium log-inactivation credit has the potential to increase disinfection by-product (DBP) formation (e.g., bromate). Calculating CT value accurately will minimize ozone dose, which will decrease operating cost and lower DBP formation, and at the same time maintain disinfection protection through implementation of scientifically based safety factors. Various methods are available for calculating CT value. The method chosen depends largely on the available information concerning ozone residual characteristics and hydrodynamic features of the ozone contactor, plus local regulatory requirements. Four methods are discussed in this paper. Each method can be used to calculate Giardia, virus, and Cryptosporidium log-inactivation credit.     

Plastic flow and fracture of Pd40Ni40P20 metallic glass under an indentor

The geometry of plastic flow under spherical and Vickers indentors in Pd₄₀Ni₄₀P₂₀ metallic glass has been investigated by sectioning and etching. The surface pile-ups and slip lines around the indentations are found to be only a small part of the total deformation. Beneath the surface extensive plastic zones are formed in which material is moved radially away from the indentor, but this movement is produced by slip on surfaces of high shear stress rather than by direct radial flow or compaction. Networks of cracks or incipient cracks also form around an indentation but are not normally visible until the material is etched.