B4C-TiB2 ceramics (TiB2 ranging 5~70 vol%) with Mo-Co-WC as the sintering additive were prepared by spark plasma sintering. In comparison with B4C-TiB2 without additive, the enhanced densification was evident in the sintered specimen with Mo-Co-WC additive. Core-rim structured grain was observed around TiB2 grains. The interface of the rim between TiB2 and B4C phases demonstrated different feature: the inner borderline of the rim exhibited a smooth feature, whereas a sharp curved grain boundary was observed between the rim and the B4C grain. The formation mechanism is discussed: the epitaxial growth of (Ti,Mo,W)B2 rim around the TiB2 core may occur as a result of the solid solution and dissolution-precipitation between TiB2 phase and the sintering additive. It was revealed that the fracture toughness increased as the content of TiB2 content increased, alongside the decreased hardness. B4C-30 vol% TiB2 specimen demonstrated the optimal combination of mechanical properties, reaching Vickers hardness of 24.3 GPa and fracture toughness of 3.33 MPa·m1/2. 相似文献
This paper presents a case study of an optimized combination of mine water control, treatment, utilization and reinjection to achieve the zero discharge of mine water. Mine water has been considered a hazard and pollution source during underground mining, so most mining enterprises directly discharge mine water to the surface after simple treatment, resulting in a serious waste of water. Moreover, discharging a large amount of mine water can destroy the original groundwater balance and cause serious environmental problems, such as surface subsidence, water resource reduction and contamination, and adverse impacts on biodiversity. The Zhongguan iron mine is in the major groundwater source area of the Hundred Springs of Xingtai, which is an area with a high risk of potential subsidence. To optimize the balance between mining and groundwater resources, a series of engineering measures was adopted by the Zhongguan iron mine to realize mine water control, treatment, utilization, and reinjection. The installation of a closed grout curtain has greatly reduced the water yield of deep stopes in the mine; the effective sealing efficiency reaches 80%. Nanofiltration membrane separation was adopted to treat the highly mineralized mine water; the quality of the produced water meets China’s recommended class II groundwater standard. Low-grade heat energy from the mine water is collected and utilized through a water-source heat pump system. Finally, zero mine water discharge is realized through mine water reinjection. This research provides a beneficial reference for mines with similar geological and hydrogeological conditions to achieve environmentally sustainable mining.
Low-dimensional carbon nanostructures are ideal nanofillers to reinforce the mechanical performance of polymer nanocomposites due to their excellent mechanical properties. Through molecular dynamics simulations, the mechanical performance of poly(vinyl alchohol) (PVA) nanocomposites reinforced with a single-layer diamond – diamane is investigated. It is found the PVA/diamane exhibits similar interfacial strengths and pull-out characteristics with the PVA/bilayer-graphene counterpart. Specifically, when the nanofiller is fully embedded in the nanocomposite, it is unable to deform simultaneously with the PVA matrix due to the weak interfacial load transfer efficiency, thus the enhancement effect is not significant. In comparison, diamane can effectively promote the tensile properties of the nanocomposite when it has a laminated structure as it deforms simultaneously with the matrix. With this configuration, the interlayer sp3 bonds endows diamane with a much higher resistance under compression and shear tests, thus the nanocomposite can reach very high compressive and shear stress. Overall, enhancement on the mechanical interlocking at the interface as triggered by surface functionalization is only effective for the fully embedded nanofiller. This work provides a fundamental understanding of the mechanical properties of PVA nanocomposites reinforced by diamane, which can shed lights on the design and preparation of next generation high-performance nanocomposites. 相似文献
Bulletin of Engineering Geology and the Environment - Many uncertainties exist in pile-stabilized slopes which make their design substantially complicated. In this paper, a first-order reliability... 相似文献
Waxy, normal and high-amylose maize starches were subjected to heat-moisture treatment (HMT) and then added to wheat flour (WF) in different ratios (1%, 5% and 10%). The properties of blends and their cooked noodles were studied to investigate the effects of HMT starches. The incorporation of HMT starch in WF led to an increase in swelling power, peak viscosity and breakdown and to a decrease in setback, thus inhibiting retrogradation, hence enhancing resultant noodle softness. Compared to the same addition ratio of native starch to WF, HMT starch led to higher tensile strength and extensibility in resultant noodles. WF with added HMT starch had higher resistant starch than with native starch. This study showed that addition of HMT maize starch has potential to bring nutritional benefits. However, it is necessary to select the proper blending ratio and amylose content of starch to add, in consideration of its effect on noodle quality. 相似文献
Element doping into the Cu2ZnSn(S,Se)4 (CZTSSe) absorber is an effective method to optimize the performance of thin film solar cells. In this study, the Cu2InxZn1-xSn(S,Se)4 (CIZTSSe) precursor film was deposited by magnetron cosputtering technique using indium (In) and quaternary Cu2ZnSnS4 (CZTS) as targets. Meanwhile, the In content was controlled using the direct current (DC) power on In target (PIn). A single kesterite CIZTSSe alloy was formed by successfully doping a small number of In3+ into the main lattice of CZTSSe. The partial Zn2+ cations were substituted by In3+ ions, resulting in improving properties of CZTSSe films. Morphological analysis showed that large grain CIZTSSe films could be obtained by doping In. The well-distributed, smooth, and dense film was obtained when the PIn was 30 W. The band gap of CIZTSSe could be continuously adjusted from 1.27 to 1.05 eV as PIn increased from 0 to 40 W. In addition, the CIZTSSe alloy thin film at PIn = 30 W exhibited the best p-type conductivity with Hall mobility of 6.87 cm2V?1s?1, which is a potential material as the absorption layer of high-performance solar cells. 相似文献
Sarcopenia is the loss of skeletal muscle mass and function with advancing age. It involves both complex genetic and modifiable risk factors, such as lack of exercise, malnutrition and reduced neurological drive. Cognitive decline refers to diminished or impaired mental and/or intellectual functioning. Contracting skeletal muscle is a major source of neurotrophic factors, including brain-derived neurotrophic factor, which regulate synapses in the brain. Furthermore, skeletal muscle activity has important immune and redox effects that modify brain function and reduce muscle catabolism. The identification of common risk factors and underlying mechanisms for sarcopenia and cognition may allow the development of targeted interventions that slow or reverse sarcopenia and also certain forms of cognitive decline. However, the links between cognition and skeletal muscle have not been elucidated fully. This review provides a critical appraisal of the literature on the relationship between skeletal muscle health and cognition. The literature suggests that sarcopenia and cognitive decline share pathophysiological pathways. Ageing plays a role in both skeletal muscle deterioration and cognitive decline. Furthermore, lifestyle risk factors, such as physical inactivity, poor diet and smoking, are common to both disorders, so their potential role in the muscle–brain relationship warrants investigation. 相似文献