Heat propagation in thermally conductive polymers of PA6 and hexagonal boron nitride

Thermally conductive polymers offer new possibilities for the heat dissipation in electric and electronic components, for example, by a three‐dimensional shaping of the heat sinks. To face safety regulations, improved fire performance of those components is required. In contrast to unfilled polymers, those materials exhibit an entirely different thermal behavior. To investigate the flammability, a phosphorus flame retardant was incorporated into thermally conductive composites of polyamide 6 and hexagonal boron nitride. The flame retardant decreased the thermal conductivity only slightly. However, the burning behavior changed significantly, due to a different heat propagation, which was investigated using a thermographic camera. An optimum content of hexagonal boron nitride for a sufficient thermal conductivity and fire performance was found between 20 and 30 vol%. The improvement of the fire performance was due to a faster heat release out of the pyrolysis zone and an earlier decomposition of the flame retardant. For higher contents of hexagonal boron nitride, the heat was spread faster within the part, promoting an earlier ignition and increasing the decomposition rate of the flame retardant.     

Numerical Investigation of the Capture of Polydisperse Particles by Charged Droplets

The capture of particles by charged droplets was simulated by considering the electrostatic interactions of droplet-droplet and droplet-particle. The results indicate that the electrostatic repulsion between droplets leads to a dynamic accumulation mode of particles. However, the droplet spacing has an insignificant effect on the capture efficiency when the electrostatic deposition predominates. The increase of droplet charge remarkably improves the capture efficiency, in which the capture of fine particles accounts for the largest proportion. Compared to the droplet charge, the droplet size shows a limited improvement in the capture efficiency. Reducing the droplet velocity prolongs the capture time instead of enhancing the capture capacity per unit time, thereby improving capture efficiency.     

人工颅骨用复合材料中微量甲基丙烯酸甲酯的气相色谱法测定

采用氢气焰离子化检测器(FID),以正丁醇为外标物,PEG-20M为固定相,甲醇作为溶剂,气相色谱法测定复合材料人工颅骨中微量MMA的含量。其相对标准偏差<0.022,平均回收率(n=4)为98.0％～99.1％。此方法操作简便,用于实际样品分析可得到满意的结果。     

低渗低温低压水敏性储气层压裂改造技术研究与应用

低渗低温低压水敏性储气层因压裂液快速破胶困难、黏土膨胀水敏伤害严重和压后压裂液返排动力不足等因素，使得压裂增产面临诸多难题。针对上述难题进行了技术攻关，形成了弱交联、低温活化剂与超量破胶剂的低温储层快速破胶技术、有机盐与无机盐双元体系复合防膨技术以及高比例液氮全程助排的排液技术。该压裂增产改造技术使牛101井头屯河组首次获得工业油气流，扩展了三塘湖盆地勘探空间。     

放置过滤器浇注系统的设计

综述了常用的网型、芯型、泡沫陶瓷过滤器的研究和应用情况。指出应根据过滤器类型，确定其在浇注系统中的安放位置并相应改变该处的结构和截面积，以便在使用过滤器净化金属的同时，保证充型速度不变。     

High-frequency small signal AC and noise modeling of MOSFETs for RFIC design

High-frequency (HF) AC and noise modeling of MOSFETs for radio frequency (RF) integrated circuit (IC) design is discussed. A subcircuit RF model incorporating the HF effects of parasitics is presented. This model is compared with the measured data for both y parameter and f_T characteristics. Good model accuracy is achieved against measurements for a 0.25 μm RF CMOS technology. The HF noise predictivity of the model is also examined with measured data. Furthermore, a methodology to extract the channel thermal noise of MOSFETs from HF noise measurements is presented. By using the extracted channel thermal noise, any thermal noise models can be verified directly. Several noise models including the RF model discussed in this paper have been examined, and the results show that the RF model can predict the channel thermal noise better than the other models     

玻璃碳电极的激光改性处理

玻璃碳电极（ＧＣＥ）用激光脉冲照射处理后，电化学反应行为发生很大变化。背景电流减小，Ｆｅ３＋／Ｆｅ２＋氧化还原电对的电极反应速率显著提高，抗坏血酸（ＡＡ）在电极上呈现明显的吸附作用。     

NK-EH500调质钢爆炸硬化的冲击动力学研究

通过试验并运用爆炸冲击动力学理论NK－EH500调质钢爆炸硬化进行了深入的研究，结果表明，金属材料存在硬化极限，调整炸药组成改变爆炸硬化可以满足不同金属材料的硬化要求，隔离式爆炸硬化有利于保护硬化工件外观的完整性，本研究对拓展爆炸硬化在实践中的应用领域具有重要的理论指导意义。