粉末冶金法制备云母/羟基磷灰石玻璃陶瓷

为了获得良好的可加工性和生物活性,采用粉末冶金法制备了云母/羟基磷灰石玻璃陶瓷.随着烧结温度的提高,材料的力学性能有所增加.在1100℃下、保温1.5 h可以获得材料的最佳力学性能,其相对密度、抗弯强度和断裂韧性分别为95%、124 MPa和2.1 MPa·m1/2.随着温度的提高,烧结过程中玻璃相的扩散速度加快并填充到剩余的孔隙中,使得材料的相对密度增加,从而提高了材料的抗弯强度.断裂韧性的提高来源于材料中高长径比的云母晶体相互交错的微观结构.     

纯铝等径角挤技术（I）——显微组织演化

研究了纯铝在 3种 (A、B和C)不同等径角挤工艺中的显微组织演化。结果表明 :纯铝经过等径角挤压变形后 ,其显微组织特征与加工路线有很大的关系。提出了立方元素扭转模型 ,分析了 3种不同加工路线的剪切面和剪切方向 ,较好地解释了采用 3种不同路线挤压后材料显微组织的演化规律。在路线C(各道次挤压间试样旋转 180°)中 ,每次挤压样品总是在相同的剪切面上发生剪切 ,每相邻道次之间的剪切方向相反 ,前一次变形产生的剪切应变被随后紧接着的下一次挤压所抵消 ,这导致了多余的剪切应变 ;在路线A(各道次挤压间试样不旋转 )中 ,有两个相交成 6 0°的剪切面 ,剪切交替地在两个剪切面上进行 ;在路线B(各道次挤压间试样旋转 90°)中 ,存在 4个不同的剪切面和剪切方向 ,挤压交替地在 4个剪切面上进行 ,X ,Y和Z平面上的晶粒都发生了剪切 ,这有利于等轴晶结构的形成     

Effects of can parameters on canned—forging process of TiAl base alloy（Ⅱ）——Mechanical behavior

1　ＩＮＴＲＯＤＵＣＴＩＯＮＴｉＡｌａｌｌｏｙｈａｓｌｏｎｇｂｅｅｎｃｏｎｓｉｄｅｒｅｄａｓａｐｒｏｍｉｓ ｉｎｇｍａｔｅｒｉａｌｆｏｒｈｉｇｈｔｅｍｐｅｒａｔｕｒｅａｐｐｌｉｃａｔｉｏｎ ,ｄｕｅｔｏｉｔｓｅｘｃｅｌｌｅｎｔｈｉｇｈｔｅｍｐｅｒａｔｕｒｅ ｐ     

Calculation of cooling rate of amorphous aluminum alloy melt-spun ribbons

Based on the heat transfer theory and liquid solidification theory, the heat transfer during the rapid solidification process of amorphous ribbons prepared by melt spinning was approximately modeled by one-dimensional heat conduction equation. Besides, integration with the temperature gradient, the relationship between the ribbon thickness and solidification time was derived according to the boundary conditions of ribbon-copper wheel. A simply theoretical model was obtained to calculate the cooling rates of aluminum amorphous ribbons. According to the above theoretical model, the critical cooling rate of aluminum amorphous ribbons by melt spinning is above 10^6 K/s, which proves that the aluminum based alloys belong to the marginal glass forming ability of alloys. The calculated results are in good agreement with other estimated values reported previously.     

具有梯度结构的涂层硬质合金刀片

研究了Co和Ti(CN)含量对梯度硬质合金的力学性能、梯度结构的影响.测试了梯度硬质合金刀片的切削性能.结果表明:随着合金钴含量的增多,合金梯度层厚度增厚,梯度结构越明显;合金的强度提高,磁饱和提高,磁力、硬度和密度减小.随着合金Ti(CN)含量的增多,合金梯度层厚度有变薄的趋势;随合金的硬度提高,合金的强度和密度减小.切削试验表明:具有梯度结构涂层硬质合金刀片的切削性能比无梯度结构涂层硬质合金刀片的切削性能优良.达到同一磨损高度hB=0.15 mm时,前者的切削寿命较后者提高了近一倍.同时随着合金钴含量的增多,硬质合金刀片的切削性能提高.     

HA/Ti composite for biomedical application by mechanical milling

In order to overcome the poor mechanical properties of HA and the low bioactivity of Ti,HA/Ti composites with various compositions were prepared by mechanical milling.The effects of milling condition and the composition on the microstructure,the density and the hardness of the composites were studied.The results show that during the ball milling process.Ti particles are refined and the homogeneity of the HA/Ti mixtures is improved;HA will partially decompose due to the existence of Ti and high sintering temperature.The microstructure of HA/Ti composites is highly dependent on the milling condition and the composition.In the microstructure.Ti phase connects to be a continuous network,and HA/Ti mixtures disperse in the network.The longer the milling time,the finer the network will be.The density of HA/T composites decreases with the content of HA increasing and the milling time prolonging,because HA deteriorates the sinterability of Ti.The hardness of HA/Ti composites increases firstly with the content of HA increasing,and then drops when the content of HA exceeds 30%.Addition of HA will strengthen the HA/T composite but will decrease the density of the composite,which accounts for the effect of HA on the hardness of the composites.     

纯铝等径角挤技术(Ⅱ)--变形行为模拟

通过有限元模拟和坐标网格，对纯铝等径角挤过程的变形行为进行了模拟和试验。结果表明，纯铝在单道次等径角挤压过程中所需的载荷随着样品位移的增加大致可分为快速增加、缓慢增加、快速增加、载荷值趋于稳定、载荷下降5个阶段。由于样品外部在主要变形区的流动速率比样品内部的快，因而样品在等径角挤压过程中会出现不均匀变形，样品底部沿宽度方向的塑性变形量明显少于样品顶部和中部的，坐标网格法实验结果也证明了这一点。在等径角挤压过程中，样品不同部位的应力状态不一致，样品内部存在压应力→拉应力的转变，样品外部存在压应力→拉应力→压应力的转变。摩擦消除后，有效应变有所增加，但并不能降低样品变形的不均匀性；采用尖角模具既能产生更大的剪切应变，又能提高变形的均匀性。     

磷化工工艺决策支持系统的构建

将决策支持系统(DSS)理论与磷化工工艺技术结合,建立磷化工工艺决策支持系统.介绍了该系统的基本理论、建立步骤、组成和数据处理框架的构成和功能,并利用层次分析法(AHP)、线性加权法和基于估计相对位置的方案排队法3种多属性决策方法实现辅助决策过程.磷化工工艺决策支持系统能够对磷矿资源合理利用、工艺优化选择提供决策辅助评判.     

Oxidation behaviors of Ni-Cr-Al superalloy foams at 1 000 ℃ in air

The oxidation behaviors of Ni-16Cr-xAl （x=4.5%, 9.0%, mass fraction） superalloy foams in air at 1000℃ were investigated. The effects of AI content on the resistance to high temperature oxidation were examined. The oxidation mechanisms of the foams were discussed. The results show that the resistance to the oxidation of the Ni-16Cr-xA1 based alloy at 1 000 ℃ increases with the content of A1 increasing from 4.5% to 9.0%. Complex oxide products are formed on the surface of the superalloy foams after the oxidation. Cr203 and A1203 are the predominant oxides for the scales of the foams with 4.5% A1 and 9% A1, respectively. Excellent high temperature oxidation resistance and superior pore conformation stability for the Ni-16Cr-xA1 based superalloy foam with 9% A1 can be mainly attributed to the formation of relatively continuous and protective A1203 oxides on the surface of the foam.     

温挤压法制备铝基非晶合金的研究进展

Al85Ni5Y10铝基非晶粉末在603K温挤压所得块体样品的相对密度超过98%, 抗压强度和弹性模量分别高达1470Mpa和145 Gpa, 是传统铝合金的2～3倍, 并有很好的耐磨、耐蚀性能和超塑性等, 可望在航天、航空和汽车制备等领域获得广泛的应用. 然而, 以Al85Ni5Y10为代表的这类铝基非晶合金材料获得工程应用的主要困难在于较难获得大尺寸的非晶材料. 为促进其快速研发, 该文简要地综合介绍和评述了温挤压法制备大块非晶合金的基本原理、方法和研发进展.