Microstructure-Property Correlation in AI_4C_3 Dispersion Strengthened Al Composite

The microstructure and tensile properties of Al_4C_3 dispersion strengthened Al composite fabricatedby reaction milling technique were investigated.It is indicated that the rod-like Al_4C_3 dispersoidshaving a diameter of 0.02-0.03 μm and a length of 0.1-0.3μm are formed by reaction of C with Al,and uniformly distributed in the Al matrix.The interface between Al_4C_3 and Al is clean and theinterfacial bonding is good.The matrix consists of the subgrains which have the size of 0.3-0.4μm,and most of the Al_4C_3 dispersoids are distributed on the subgrain boundaries.The 11 vol.-%Al_4C_3/Al composite exhibits an UTS (ultimate tensile strength) of 400 MPa and anelongation-to-failure of 8.0%.     

CCD型束流截面探测器

CCD型束流截面探测器的主要特点是使用电荷耦合器件做传感器,用束流同步光中的可见光成份做为信号源。该探测器同时具有模拟量和数字量两种输出,工作周期短,速度高,不影响束团粒子寿命,在电子储存环物理运行中,是一种有效的探测设备。     

兰州重离子加速器大型真空室

已建成的兰州重离子加速器的真空室是一个大型整体结构的超高真空容器,直径约10m,高4.5m,重65000kg,内表面积211m~2,容积100m~3,工作真空度为5×10~(-5)Pa。采用有限单元法在计算机上用SAP-5C程序对真空室受力分析进行了计算。真空室结构材料选用瑞典Uddeholm钢厂生产的316 L 超低碳不锈钢。承制此大型容器的是航天工业部风华机器厂。由于结构庞大,首先将真空室分成八大块和几小块在工厂制造,然后运至现场焊制成一整体容器并进行机械加工。所有密封焊缝均用着色渗透液,X-射线探伤和氦质谱探漏仪进行检查和探漏。     

Alkali-metal Na Adsorption and Promoted Oxidation on Si(100)2×1 Surface

The alkali-metal Na adsorption on Si(100)2×1 surface and its promoted oxidation and Si oxidegrowth have been investigated by means of thermal desorption,work function,Auger electronspectroscopy and photoemission electron spectroscopy.The experimental data showed that therewas a new state,interface electron state,near the Fermi level after the deposition of Na atoms.It wasfound that the presence of Na always caused an increase of the oxygen initial uptake whereas thepromotion of Si oxide growth was observed only at the coverage of Na greater than 0.5 ML.A newmechanism of Na-promoted Si oxide growth is suggested in this paper.     

网络计划之实践

通过对所参与工程的实践体会。介绍网络计划技术在旧厂改造工程中的重要作用和几种主要管理方法。     

钢筋砼矩形截面受弯构件优化设计

对钢筋砼矩形截面受弯构件提出一种优化的方法。     

位置控制器与通用变频器APC系统

在每一周期的开始时的速度值V1预设定到传动装置上进行速度预控制，同时，反馈回来的实际值Sj与S1进行比较计算，得出当时偏差值△S，此偏差值△S乘以比例系数Ksp，得到Vk叠加在Vt上，得出传动装置应具有的速度控制信号V，然后V经速度／电压变换和D／A转换向传动系统的速度控制发出控制信号Uα控制执行机构的定位。调节Ksp的值使系统无超调无振荡。     

变压器事故原因分析

通过分析一次变压器事故的原因。指出变压器实际运行中存在的问题。并结合自己的工作经验提出科学的改进建议。     

退火损伤对Er注入GaAs和Yb注入InP发光的影响

本文报道了CaAs∶Er、InP∶Yb发光样品的二次离子质谱、X-射线双晶衍射测量结果及其与Er离子的表面成份的关系.分析讨论了退火损伤对GaAs∶Er和InP∶Yb发光的影响以及Er~(3+)复合体发光中心模型.