PVC树脂生产中产生塑化片的原因与改进措施

分析了PVC树脂生产中产生塑化片的原因,针对储槽搅拌器、离心机、星形下料器和输送管线提出了改进措施,并在料仓底部下料管线处增加了振动筛,改造后效果良好.     

Understanding grain refining and anti Si-poisoning effect in Al-10Si/Al-5Nb-B system

Grain refinement is critical for fabricating high-quality Al-Si casting components in the application of automobile and aerospace industries,while the well-known Si-poisoning effect makes it difficult.Nbbased refiners offer an effective method to refine Al-Si casting alloys,but their anti Si-poisoning capability is far from being understood.In this work,the grain refining mechanism and the anti Si-poisoning effect in the Al-10 Si/Al-5 Nb-B system were systematically investigated by combining transmission electron microscope,first-principles calculations,and thermodynamic calculations.It is revealed that NbB₂provides the main nucleation site in the Al-10 Si ingot inoculated by 0.1 wt.%Nb Al-5 Nb-B refiner.The exposed Nb atoms on the(0001)NbB₂and(1-100)NbB₂surface can be substituted by Al to form(Al,Nb)B₂intermedia layers.In addition,a layer of NbAl₃-like compound(NbAl₃')can cover the surface of NbB₂with the orientation relation of(1-100)[11-20]NbB_2//(110)[110]NbAl₃'.Both of the(Al,Nb)B₂and NbAl₃'intermedia layers contribute to enhancing the nucleation potency of NbB₂particles.These discoveries provide fundamental insight to the grain refining mechanism of the Nb-B based refiners for Al-Si casting alloys and are expected to guide the future development of stronger refiners for Al-Si casting alloys.     

高效液相色谱法同时测定化妆品中的7种香豆素

基于香豆素类化合物在化妆品中的使用情况及其对人体健康的危害,采用C18色谱柱作为分析柱,通过优化试验条件建立了一种可准确、简便测定化妆品中多种香豆素类化合物的高效液相色谱法。试验结果表明,7种香豆素类化合物的保留时间和峰面积的相对标准偏差分别小于0.1%和2%,且检出限均低于40μg/L;通过样品加标试验,得到7种目标化合物的回收率为80%~94%。所建立方法具有快速、简便、准确、灵敏的特点,是测定化妆品中多种香豆素类化合物的有效方法。     

Different hydrothermal corrosion results between two sides of sodalime float glass and the possible corrosion mechanism

Sodalime float (SF) glass is widely used in our societies and industries. Hydrothermal corrosion method is one of the effective ways to prepare a superhydrophobic glass, but there is still lack of knowledge about hydrothermal corrosion behavior and mechanism of SF glass. We have hydrothermally treated SF glass at 180 °C for different time, and tried to reveal the aqueous corrosion process of SF glass. We have characterized the morphologies and chemical compositions of samples, and found that (1) the two sides of SF glass have different corrosion resistances, and (2) a multilayer structural coating with a nanoflake layer (Mg-rich gel layer), a nanowire layer (Ca-rich gel layer), and a porous layer (etched layer) is formed on the air-side of SF glass. Based on the experimental results, we have proposed an aqueous corrosion mechanism of SF glass. The insights of the hydrothermal corrosion behaviors and mechanism provide helpful guidelines to glass surface structural control and functionalization.     

基于高频损耗比的干式空心电抗器制造缺陷检测方法及应用探讨

本文通过分析电抗器因制造工艺导致少匝和极限工艺偏差时600Hz损耗,提出高频损耗可作为电抗器制造缺陷的检测手段及其适用范围,并以600Hz的实测损耗与理论损耗之比是否超过1.5作为判据,以同组任两台损耗之比是否超过1.5作为辅助判据,同时列举应用实例.     

Effect of an abrupt change in pulling rate on microstructures of directionally solidified Al2O3-Er3Al5O12 eutectic and off-eutectic composite ceramics

Directionally solidified microstructures of Al₂O₃-Er₃Al₅O₁₂ eutectic and off-eutectic in situ composite ceramics were explored under abrupt-change pulling rate conditions. Corresponding temperature distributions and interface locations were studied. In eutectic composition, fluctuation of eutectic spacing occurred when the pulling rate increased abruptly. A gradually increase or abrupt increase in eutectic spacing was observed when the pulling rate decreased abruptly. In hypoeutectic and hypereutectic compositions, formation of the primary phases were suppressed when the pulling rate increased abruptly from 10?µm/s to 100?µm/s, while primary phases precipitated when the pulling rate decreased abruptly from 100?µm/s to 10?µm/s. The interface altitude decreased after the pulling rate increased abruptly, but increased after the pulling rate decreased abruptly. The liquid composition restriction (around the eutectic composition) at the eutectic interface plays an important role in the suppression of the primary dendrite and coupled eutectic oxides can be obtained in off-eutectic compositions even under higher solidification rate conditions.     

Analysis of the ionospheric variability based on wavelet decomposition

In this work,the ionospheric variability is analyzed by applying the wavelet decomposition technique to the noontime fo F2,F10.7,interplanetary magnetic field(IMF)Bz,Ap,and lower thermospheric temperature at pressure of 10?4 h Pa in 2002.Results show that the variance of periodic oscillations in the ionosphere is largest in the 2–4-day period and declines with the increase of the period.The maximum variance of the periodic oscillations in solar irradiation is in the 16–32-day period.For geomagnetic activities,most of the variance is about equally distributed on intervals of periods shorter than 32 days.Variance distributions of IMF Bz and lower thermospheric temperature are similar to those of the ionosphere.They show the maximum in the 2–4-day period and decline with the increase of the period.By analyzing the distributions of the variances,the potential connections between the ionosphere and the external sources are discussed.     

2A12铝合金化学铣切加工工艺探讨

为了精确加工2Al2铝合金,探讨了化铣时间和温度对其化铣速率及表面粗糙度的影响,采用现代技术对化铣工件的力学性能进行了测试与分析.结果表明:延长非化铣部位保护胶固化时间并使保护部位向非加工面位移3～5 mm可很好地解决未化铣区域的腐蚀问题;随化铣时间的延长,化铣速率降低,且化铣温度与化铣速率呈现正相关性;化铣表面的粗糙度随化铣时间的延长而增加,随化铣温度的升高呈先减小后增加的趋势;化铣后材料的抗拉强度和屈服强度均有所提高.