Hydraulic reactivity and cement formation of baghdadite

In this study, the hydraulic reactivity and cement formation of baghdadite (Ca₃ZrSi₂O₉) was investigated. The material was synthesized by sintering a mixture of CaCO₃, SiO₂, and ZrO₂ and then mechanically activated using a planetary mill. This leads to a decrease in particle and crystallite size and a partial amorphization of baghdadite as shown by X-ray powder diffraction (XRD) and laser diffraction measurements. Baghdadite cements were formed by the addition of water at a powder to liquid ratio of 2.0 g/ml. Maximum compressive strengths were found to be ~2 MPa after 3-day setting for a 24-h ground material. Inductively coupled plasma mass spectrometry (ICP-MS) measurements showed an incongruent dissolution profile of set cements with a preferred dissolution of calcium and only marginal release of zirconium ions. Cement formation occurs under alkaline conditions, whereas the unground raw powder leads to a pH of 11.9 during setting, while prolonged grinding increased pH values to approximately 12.3.     

Introduction of a nonlinearity measure for principal component models

Although principal component analysis (PCA) is an important tool in standard multivariate data analysis, little interest has been devoted to assessing whether the underlying relationship within a given variable set can be described by a linear PCA model or whether nonlinear PCA must be utilized. This paper addresses this deficiency by introducing a nonlinearity measure for principal component models. The measure is based on the following two principles: (i) the range of recorded process operation is divided into smaller regions; and (ii) accuracy bounds are determined for the sum of the discarded eigenvalues. If this sum is within the accuracy bounds for each region, the process is assumed to be linear and vice versa. This procedure is automated through the use of cross-validation. Finally, the paper shows the utility of the new nonlinearity measure using two simulation studies and with data from an industrial melter process.     

RF SiP技术正转向无线设计主流

第1部分射频系统级封装(RF SiP,RF System-in-Pack-age)技术是一种对无线通信非常有用的封装平台,无线通信被如下事实所困,但由于目前SiP设计仍     

State estimation for high-dimensional chemical processes

The application of conventional observer designs for high-dimensional systems may not always be practical due to high computational requirements or the resulting observers being too sensitive to measurement noise. In order to address these issues, this paper presents two observer design techniques for state estimation of high-dimensional chemical processes. One technique is used for systems with inputs, whereas the other one is specifically geared towards systems that are not excited from the outside. Both of these observers are applicable to linear and with a modification to non-linear systems.The main idea behind the presented observer designs is that a reduced-order observer is implemented instead of a conventional state estimator. The motivation is that subspaces, which are close to being unobservable, cannot be correctly reconstructed in a realistic setting due to measurement noise and inaccuracies in the model. The presented approaches make use of this observation and only reconstruct the parts of the system where accurate state estimation is possible. The observer designs are illustrated on a 30-tray distillation column model. Additionally, it has been shown that the location of process measurements has a major effect on the performance of the presented reduced-order observers.     

Dynamic optimal experimental design yields marginal improvement over steady‐state results for computational maximisation of regulatory T‐cell induction in ex vivo culture

The isolation of T cells, followed by differentiation into Regulatory T cells (Tregs), and re‐transplantation into the body has been proposed as a therapeutic option for inflammatory bowel disease. A key requirement for making this a viable therapeutic option is the generation of a large population of Tregs. However, cytokines in the local microenvironment can impact the yield of Tregs during differentiation. As such, experimental design is an essential part of evaluating the importance of different cytokine concentrations for Treg differentiation. However, currently only single, constant concentrations of the cytokines have been investigated. This work addresses this point by performing experimental design in silico which seeks to maximize the predicted induction of Tregs relative to Th17 cells, by selecting an optimal input function for the concentrations of TGF‐β, IL‐2, IL‐6, and IL‐23. While this approach sounds promising, the results show that only marginal improvements in the concentration of Tregs can be achieved for dynamic cytokine profiles as compared to optimal constant concentrations. Since constant concentrations are easier to implement in experiments, it is recommended for this particular system to keep the concentrations constant where IL‐6 should be kept low and high concentrations of TGF‐β, IL‐2, and IL‐23 should be used.Inspec keywords: patient treatment, molecular biophysics, proteins, cellular biophysics, diseasesOther keywords: Tregs relative, optimal input function, dynamic cytokine profiles, optimal constant concentrations, IL‐23, computational maximisation, regulatory T‐cell induction, inflammatory bowel disease, viable therapeutic option, local microenvironment, Treg differentiation, single concentrations, predicted induction, dynamic optimal experimental design, interleukin‐2, IL‐6, transforming growth factor‐β     

The influence of design aesthetics in usability testing: Effects on user performance and perceived usability

This article examined the effects of product aesthetics on several outcome variables in usability tests. Employing a computer simulation of a mobile phone, 60 adolescents (14-17 yrs) were asked to complete a number of typical tasks of mobile phone users. Two functionally identical mobile phones were manipulated with regard to their visual appearance (highly appealing vs not appealing) to determine the influence of appearance on perceived usability, performance measures and perceived attractiveness. The results showed that participants using the highly appealing phone rated their appliance as being more usable than participants operating the unappealing model. Furthermore, the visual appearance of the phone had a positive effect on performance, leading to reduced task completion times for the attractive model. The study discusses the implications for the use of adolescents in ergonomic research.