Polymer networks based on α,ω-methacrylate-terminated poly(1,3-dioxolane)

α,ω-Methacrylate-terminated poly(1,3-dioxolane)s (polyDXL) were synthesized by cationic ring-opening polymerization of DXL in the presence of methylene-bis(oxyethylmethacrylate) as transfer agent. If the initiator concentration is small compared with the transfer agent concentration, the molecular weights of the polymers are governed by the ratio of the reacted monomer to the reacted transfer agent. The α,ω-methacrylate-terminated polyDXLs obtained undergo free radical polymerization with formation of polyacetal networks. The properties of the networks as function of the molecular weight of the corresponding prepolymers are reported.     

Effects of flux enhancing polymer on the characteristics of sludge in membrane bioreactor process.

A newly developed membrane performance enhancer (MPE) was used to prevent membrane fouling in a membrane bioreactor (MBR) process. It transpired that 1,000 mg/l of MPE reduced polysaccharide levels from 41 mg/I to 21 mg/I on average under the experimental condition. Repeated experiments also confirmed that 50-1,000 mg/l of MPE could reduce membrane fouling significantly and increase the intervals between membrane cleanings. Depending on MPE dosages and experimental conditions, trans-membrane pressure (TMP) increase was suppressed for 20-30 days, while baseline TMP surged within a few days. In addition, MPE allowed MBR operation even at 50,000 mg/l of total solid and reduced permeate COD. However, no evidence of toxicity for sludge was found from respiratory works.     

Indoor temperature changes in retrofit homes

The behavioral response (e.g. changes in indoor temperatures, attention to window and door openings) to residential technical efficiency improvements (e.g. attic insulation, storm windows) is an important and largely unresolved issue. Although there is considerable discussion concerning the extent to which households take back some of the energy savings due to technical efficiency improvements in increased comfort, there is almost no empirical evidence on the subject.Detailed electricity billing data (from mid-1981 to mid-1983) were analyzed for 79 households that received financial assistance from the Bonneville Power Administration to retrofit their homes in mid-1982. The mean retrofit expenditure in these homes was $1900; the mean reduction in annual electricity use was 4700 kWh, of which 83% was due to reductions in space heating electricity use. Analysis of the electricity billing data suggests that these households increased their indoor temperature settings after retrofit by almost 1 °F on average. This temperature increase led to an estimated average loss of almost 600 kWh of electricity saving. In other words, roughly 10% of the energy saving due to retrofit was taken back in terms of increased comfort. These results concerning changes in indoor temperatures should be viewed cautiously because of limitations in the analytical method and the large variation across households.     

Preliminary irradiation test results from the Yankee Atomic Electric Company reactor vessel test irradiation program

The Yankee Atomic Electric Company test irradiation program was implemented to characterize the irradiation response of representative Yankee Rowe reactor vessel beltline plate materials and to remove uncertainties in the analysis of existing irradiation data on the Yankee Rowe reactor vessel steel. Plate materials each containing 0·24 w/o copper, but different nickel contents at 0·63 w/o and 0·19 w/o, were heat treated to simulate the Yankee vessel heat treatment (austenitized at 982°C (1800°F)) and to simulate Regulatory Guide 1·99 database materials (austenitized at 871°C (1600°F)). These heat treatments produced different microstructures so the effect of microstructure on irradiation damage sensitivity could be tested. Because the nickel content of the test plates varied and the copper level was constant, the effect of nickel on irradiation embrittlement was also tested. Correlation monitor material, HSST-02, was included in the program to benchmark the Ford Nuclear Reactor (University of Michigan Test Reactor) which had never been used before for this type of irradiation program. Materials taken from plate surface locations (versus 1/4T) were included to test whether or not the improved toughness properties of the plate surface layer, resulting from the rapid quench, are maintained after irradiation. If the improved properties are maintained, pressurized thermal shock calculations could utilize this margin. Finally, for one experiment, irradiations were conducted at two irradiation temperatures (260°C and 288°C) to determine the effect of irradiation temperature on embrittlement. The preliminary results of the irradiation program show an average temperature effect of 38°C for a 28°C difference in irradiation temperature. The results suggest that for nickel bearing steels, the superior toughness of plate surface material is maintained after irradiation and for the copper content tested, nickel has little effect on irradiation response. No apparent microstructure effect on irradiation response was noted and the HSST-02 material's response to irradiation was similar to results from power reactor and other test reactor tests, thus qualifying the Ford Test Reactor for irradiation experiments such as those conducted for the Yankee Atomic program.     

Photoelectric conversion of photosynthetic reaction center in multilayered films fabricated by layer-by-layer assembly

Multilayered protein films which contained ordered layers of photosynthetic reaction center (RC) from Rhodobacter Sphaeroides (RS601) were assembled by means of alternate electrostatic adsorption with positively charged poly(diallyldimethylammonium chloride) (PDDA). The assembly of RC was monitored by spectrometry and photocurrent measurement. Linear film growth was observed up to about 20 cycles of adsorption. For the monolayer film, the photocurrent was about 8.5 nA cm⁻². For the multilayered film, the total photocurrent was about 77 nA cm⁻² for the 24-layer RC film, while the average photocurrent increment per adsorption cycle was about 3.2 nA cm⁻². The overall light-to-electricity conversion efficiency for a 24-layer film was about eight times higher than that for the monolayer one. The effects of electrode potential and pH on the photocurrent were also measured to illustrate the light-to-electric converting mechanism.     

Intrinsic reactivity of gold nanoparticles: Classical, semi-empirical and DFT studies

Gold nanoparticles used in most experiments (1–10 nm) in gold catalysis show varying degrees of reactivity, with particles below 5 nm generally being more reactive. The origin of this activity is a subject of a number of model experiments and theoretical studies on either clusters of a few atoms in size or extended surfaces (smooth or stepped). In the work described here, a classical theory for the variation of the metal workfunction with cluster size, Extended Hückel Theory (EHT) calculations combined with DFT calculations, as well as a carbon monoxide (CO) chemisorption model are combined to develop a relationship between metal particle size and the particle's reactivity towards CO. For gold, it is shown that while the contribution of the d-band hybridization energy to the total CO chemisorption energy is unfavourable for bulk gold, this is not true for gold particles below 5–6 nm. That is, the d-band hybridization energy is negative for small gold particles. This is believed to be explanation of the onset of high reactivity for small gold particles.