Universal probability-free prediction

We construct universal prediction systems in the spirit of Popper’s falsifiability and Kolmogorov complexity and randomness. These prediction systems do not depend on any statistical assumptions (but under the IID assumption they dominate, to within the usual accuracy, conformal prediction). Our constructions give rise to a theory of algorithmic complexity and randomness of time containing analogues of several notions and results of the classical theory of Kolmogorov complexity and randomness.     

First results on patient dose measurements from conventional diagnostic radiology procedures in Serbia and Montenegro

The objective of this work is to assess patient doses for the most frequent X-ray examinations for the first time in Serbia and Montenegro. A total of 510 procedures for 11 different examination categories in 3 general hospitals were analysed. Mean and median entrance surface air kerma (ESAK) and kerma area product (KAP) values followed by mean effective doses were reported. Using X-ray tube output data, ESAK for each radiographic examination was calculated, as well as the effective dose for each patient. Except for chest PA examination, all estimated doses are less than stated European and International Atomic Energy Agency (IAEA) reference levels for simple radiographic examinations. For complex examinations involving fluoroscopy and radiography total KAP was measured and contributions from fluoroscopy and radiography were assessed. The study of KAP confirms that the dose level for complex fluoroscopy investigations is closely related to the technique and individual patient variation in terms of fluoroscopy time and number of radiography exposures. The obtained values are comparable to those reported in the UK. Survey data are aimed aid development of a national quality control and radiation protection programme for medical exposures.     

Mixing of a lignin‐based slurry fuel

Lignin‐based slurry fuels are a potential alternative to fossil fuels in kraft pulp mills. Lignogels — mixtures of lignin, fuel oil, water and surfactant — are non‐Newtonian fluids, with shear‐thinning and thixotropic behaviour. Their mixing was investigated in tanks with volumes of 3 and 30 L. An A310 hydrofoil impeller was used in all experiments. Results were compared with measurements in Newtonian fluids, used to characterize the impeller over a broad range of Reynolds numbers (1–500 000). An aqueous CMC solution was also used for characterization of the impeller and estimation of the Metzner‐Otto constant. Results in the transition region were corrected by introduction of two empirical parameters.     

Analysis of Steady‐State Temperature Profiles from a Laboratory Reactor by Means of a Process Simulator

A process simulator was used for the analysis of steady‐state results from a laboratory‐scale tubular reactor for the oxidation of carbon monoxide over a platinum catalyst. From a set of 14 steady‐state experiments, temperature profiles were simulated with two adjustable parameters recovered by optimizing the fit: k°, the pre‐exponential portion of the rate constant, and h_out, the outer wall heat transfer coefficient for the reactor tube. Simulation showed that despite elaborate insulation the reactor did not behave adiabatically. Simulation also predicted fairly well the magnitude of phenomena such as ignition, extinction, and rate hysteresis (caused by changes in feed temperatures or concentrations) but at temperatures below the experimental values.     

Patient doses for barium meal examination in Serbia and Montenegro and potentials for dose reduction through changes in equipment settings

Patient doses for barium meal examination performed at three general hospitals in Serbia and Montenegro were measured using a kerma-area product (KAP) meter. The results were analysed in order to obtain dose-related parameters. Although the observed doses were within the range reported in other studies, intra-hospital and inter-hospital dose variations were significant. Mean KAP values for total examination in three hospitals were 8.4, 24.4 and 13.9 Gy cm2, respectively. Contribution from fluoroscopy was greater than from radiography. Factors contributing to the increased dose delivery were determined and the recommendations on radiographic techniques were made. Changes in radiography settings allowed dose reduction up to 48% in the radiographic part of examination, that is, up to 12% in total dose without loss of image quality. In addition, fluoroscopy time was noted as the second major contributor to the dose variations. The results demonstrated the need for standardisation of practice for barium meal examination in the country.     

Reduction of mouldboard plough share wear by a combination technique of hardfacing

This paper presents comparison of wear of regular mouldboard plough shares and two plough shares made of different basic materials, steel EN 10027 (HF-1) and EN 50Mn7 (HF-2), hardfaced by a combination of two welding processes, namely shielded metal arc welding (SMAW) and high-frequency induction welding (HFIW). Wear was determined by measurements of the changes of dimensions and weight during ploughing of sandy clay soil in Croatia. The dimensions and weight losses were lower for both types of hardfaced plough shares in comparison to regular shares, and lower fuel consumption and a higher rate of work were achieved with hardfaced plough shares. Hardfaced plough shares also offer lower production costs in comparison to regular plough shares. According to the overall results, this protection method can be recommended as an efficient solution for plough share wear protection.