Augmentation of boiling heat transfer from horizontal cylinder to liquid by movable particles

This paper presents a series of experimental results on a passive augmentation technique of boiling heat transfer by supplying solid particles in liquid. A cylindrical heater 0.88 mm in diameter is placed in saturated water, in which a lot of mobile particles exist, and the nucleate and film boiling heat transfer characteristics are measured. Particle materials used were alumina, glass, and porous alumina, and the diameter ranged from 0.3 mm to 2.5 mm. Particles are fluidized by the occurrence of boiling without any additive power, and the heat transfer is augmented. The maximum augmentation ratio obtained in this experiment reaches about ten times the heat transfer coefficient obtained in liquid alone. The augmentation ratio is mainly affected by the particle material, diameter, and the height of the particle bed set at no boiling condition. The augmentation mechanism is discussed on the basis of the experimental results. © 2001 Scripta Technica, Heat Trans Asian Res, 31(1): 28–41, 2002     

Micromachined piezoelectric force sensors based on PZT thin films

A micromachined lead zirconate titanate (PZT) force sensor for scanning force microscope (SFM) is conceptualized by its piezoelectricity. The fabrication procedure is interpreted, and mechanical characteristics of the micromachined PZT force sensors with various lengths are studied in this paper. A compact SFM is constructed by using the piezoelectric PZT sensor. A very clear image is taken by this SFM. The current study of the micromachined PZT force sensor can be considered as a breakthrough of design of SFM as well as a good example of integrated piezoelectric microdevices     

Graphite formation on Ni film by chemical vapor deposition

Thin film formation of graphite by chemical vapor deposition using 2-methyl-1,2′-naphthyl ketone as a starting material was carried out on Ni film substrates. On Ni films directly deposited on quartz glass, the graphite films were obtained when the Ni film thickness was above 1 000 Å and above 5 000 Å at 700 °C and 1 000 °C, respectively. Depositions on thinner Ni film substrates comprise amorphous carbon (a-C) or graphite tubes which was owing to the thermal coagulation of the Ni film into droplets. On the other hand, graphite film was obtained on the Ni film with thickness 10 Å when a-C was inserted between the Ni film and the quartz glass. The coagulation of the Ni film is considered to be avoided by inserting a-C layer.     

Permeation of Zidovudine and Probenecid from Oily Bases Containing Alcohols Through Rat Skin

Permeation of zidovudine (3'-azido-3'-deoxythymidine, AZT) and probenecid from oily bases containing an alcohol through rat skin was examined. Isopropyl myristate (IPM), as an oily vehicle, showed a penetration enhancing effect for AZT and probenecid. Ethanol, n-propanol, and n-butanol were used as additives in IPM and were examined for their own permeation and the enhancing effect on the permeation of AZT and probenecid. The skin permeation of AZT and probenecid from IPM was enhanced by addition of the alcohol in IPM. The degree of the enhancement was decreased with increasing lipophilicity of the alcohol used. me permeation rate of the drug from those systems was shown to be governed by penetration-enhancing effects of the oily base and alcohol, and the penetration of the alcohol itself through the skin.     

Impulse breakdown voltages of triggered multistage vacuum gap

Several sealed-off triggered vacuum gaps are connected in series to improve hold-off voltage. The characteristics of impulse breakdown voltage of these series-connected gaps are investigated experimentally. The sum hold-off voltage of series-connected gaps decreases to a unit hold-off voltage when the maximum value of voltage division ratio across the gaps increases to unity. Self-breakdown probability of the series-connected gaps is always higher than that of a single gap under the same conditions. Hence, stage efficiency of the multistage gap decreases with increasing number of stages. Its value is 90 percent with 2-stage gap and 75 percent with 5-stage gap, respectively, under the same voltage division ratio and the same gap length (2.0 mm) in each stage. Triggered breakdown voltage of 2- or 3- stage gap is several hundred volts when all gaps are triggered simultaneously at the peak of the main impulse wave and a working voltage range is nearly 100 percent in this case. The working voltage range decreases with number of stages. Its value is 45 percent with 3-stage gap and 15 percent with 5-stage gap, respectively, when one triggered gap is fired for switching.     

An investigation of water-gas transport processes in the gas-diffusion-layer of a PEM fuel cell by a multiphase multiple-relaxation-time lattice Boltzmann model

In order to study water-gas transport processes in the gas-diffusion-layer (GDL) of a proton exchange membrane (PEM) fuel cell system, a multiphase, multiple-relaxation-time lattice Boltzmann model is presented in this work. The model is based on the mean-field diffuse interface theory and can handle the multiphase flows with large density ratios and various viscosities. By using the standard bounce back boundary condition and an approximate average scheme for the non-slip and wetting boundary walls, respectively, detailed liquid-gas transportation in the GDL, in which exact boundary condition is difficult to be implemented, can be simulated. Unlike most of lattice Boltzmann methods based on the Bhatnagar–Gross–Krook collision operator, the present model shows a viscosity-independent velocity field, which is very important in simulating multiphase flows where various viscosities coexist. We validate our model by simulating a static droplet on a wetting wall and compare with theoretical predictions. Then, we simulate a water-gas flow in the GDL of a PEM fuel cell and investigate the saturation-dependent transport properties under different conditions. The results are shown to be qualitatively consistent with the previous numerical and theoretical works.     

A study of suppression of vapor explosions by adding inversely soluble polymers

The mechanism of the suppression of vapor explosions by adding inversely soluble polymers in water is studied. Vapor explosion experiments and quench experiment are conducted using a silver test piece. Polymetric solution (polyethylene oxide), of concentrations from 0 to 500 wppm, whose normalized viscosity (by water) varies from 1.00 to 2.00, is used. No vapor explosion is observed in the aqueous polymer solution at a concentration higher than 200 wppm. Quench experiments using the silver test piece submerged in the polymer solution and water are performed in order to examine the stability of film boiling. The suppression of the vapor film collapse is attributed to the precipitation of polyethylene as a gel around the vapor film. © 2002 Wiley Periodicals, Inc. Heat Trans Asian Res, 31(4): 297–306, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.10037     

Reliability of Au bump––Cu direct interconnections fabricated by means of surface activated bonding method

As a room temperature bonding method, surface activated bonding (SAB) method has been introduced to be one of the most appropriate interconnection methods for the next generation of electronic packaging. Thus it is important to study the reliability of SAB interconnection in long term life test.In this paper, interconnections of Au bump and Cu film bonded by SAB method were performed in high temperature thermal aging test. Degradation of properties such as electrical resistance, shear strength of bump and interface microstructure during aging process were studied to investigate the failure mechanism of the interconnection. Intermetallic compound Cu₃Au was found formed at the interface during thermal aging, and it causes evolvement of the properties and failure mode of the interconnection changing in shear test. Results reveal that SAB is suitable for the interconnection between Au bump and Cu film and it is reliable in thermal reliability test.