Distribution of carbon contamination in MgAl2O4 spinel occurring during spark-plasma-sintering (SPS) processing: I – Effect of heating rate and post-annealing

Carbon contamination from the carbon paper/dies during spark-plasma-sintering (SPS) processing was examined in the MgAl₂O₄ spinel. The carbon contamination sensitively changes with the heating rate during the SPS processing. At the high heating rate of 100 °C/min, the carbon contamination having organized structures occurred over almost the entire area from the surface to deep inside the SPSed spinel disk. In contrast, at the slow heating rate of 10 °C/min, the carbon contamination having disordered structures occurred only around the surface area. The carbon phases transform into high pressure CO/CO₂ gases by post-annealing in air and lead to pore formation along the grain junctions. The pore formation significantly occurs at the high heating rate due to the large amount of the contaminant carbon phases. This suggests that if once the carbon contamination was formed in the materials, it is very difficult to remove the carbon phases from the materials.     

Oxidation of doped europium in BaMgAl10O17 by annealing studied by x‐ray‐absorption fine‐structure measurements

Abstract— We studied the influence of annealing in air on doped europium in BaMgAl₁₀O₁₇ by performing x‐ray absorption fine‐structure measurements. We determined the oxidation of doped divalent europium by annealing in air at over 500°C. The interatomic distance between the europium and the surrounding oxygen atoms was compressed by oxidation. It also appears that the oxidation process of europium is determined by the diffusion of oxygen into BaMgAl₁₀O₁₇.     

High performance liquid chromatographic separation of diacylglycerol acetates to quantitate disaturated species of lung phosphatidylcholine

A high-performance liquid chromatographic (HPLC) separation of diacylglycerol acetates to quantitatite disaturated species of lung phosphatidylcholine (PC) was studied. The diacylglycerol acetates were applied on a reversed phase column, eluted by an isocratic solvent, acetonitrile/isopropanol/water (35:15:1, v/v/v) at a flow rate of 1 ml/min, and detected by differential refractometry (RI). This isocratic HPLC method was useful to separate disaturated species from the others of lung PC. The quantitative analysis of the molecular species separated by HPLC was studied by RI detection. Chroamtograms obtained by RI detection and radioactivity determination of diacylglycerol [³H]acetates prepared by [³H]acetic anhydride were almost identical. The RI detector responsed in the same degree for different, authentic standards of diacylglycerol acetates. The detection limit with RI detection was about 30 nmoles. Molecular species of PCs from human lung and carcinoma tissues were analyzed by this HPLC method. The contents of disaturated species were very similar to those reported previously. These results indicate that RI detection is very useful in the nmole range for the quantitative analysis among the molecular species containing disaturated species.     

A flow simulation for the epoxy casting process using a 3D finite‐element method

A three‐dimensional flow simulation for epoxy casting has been developed. A control‐volume‐based finite‐element method is employed, containing a conservative upwind formulation for the advection terms and equal order interpolations for all variables. This simulation predicts the non‐isothermal and reactive flow behavior under the gravity. The viscosity and reaction‐rate parameters were estimated by using a dynamic rheometer and a differential scanning calorimeter. The predicted flow front advancement and temperature profiles in the calculation domain similar to the mold cavity were in close agreement with the corresponding experimental results. The variation of epoxy surface configuration with flow rate also showed the same tendency between the prediction and the experiment. This simulation seems to be applicable not only to the epoxy casting, but also to other molding processes of various thermoset resins. POLYM. ENG. SCI. 45:364–374, 2005. © 2005 Society of Plastics Engineers.     

Preparation of polyimide-epoxy composites

The formation of a three dimensional network of crosslinked epoxy leads all unmodified epoxies to have inherent brittleness and relatively low degradation temperatures. Polyimides, on the other hand, are widely used for applications that require high degrees of flexibility and thermal resistance. Here, we have focused on the preparation of epoxy systems cured with polyamic acids instead of traditional amino-group-containing hardening agents. The cure behavior and potential reaction mechanisms of EPON 828 resin and polyamic acid mixtures were evaluated by DSC and TGA. Thermal analysis showed a complex reaction sequence taking place in the mixture and also determined the extent of reaction of the polyamic acid with itself and the competitive reaction of the polyamic acid with the epoxy. The compositions of the mixtures were varied to see the dependence of the cure behavior on component concentrations. Solutions of the two components did not phase separate and also phase separation was not apparent either optically or microscopically in the cured samples. This phase behavior was attributed to a unique in situ reaction. A novel solvent system for the polyamic acid precursor was also used.     

Two geometrical isomers of linoleic acid: Improved total syntheses

The total syntheses of 9(Z),12(E)- and 9(E),12(Z)-octadecadienoic acids have been carried out. A useful intermediate in both syntheses, 8-bromo-octanoic acid, recently has become available from commercial sources. This compound has been used to expedite the preparation of these isomers. The remaining carbon atoms were derived from propargyl alcohol along with either 1-heptyne or acetylene and 1-bromopentane. Because the overall yield for each sequence was roughly 15% and there were no extraordinary reaction conditions in any of the synthetic steps, the compounds could be prepared readily in multiple gram quantities. The syntheses of the two compounds were supported by data from a variety of spectroscopic techniques.     

Question hard, answer simply: A comment on Storms et al. (2003).

It seems clear that, for whatever reasons, the dementia of the Alzheimer type patient group (as well as other patient groups) exhibits behavior that is different from the normal control group. G. Storms, T. Dirikx, J. Saerens, S. Verstraeten, and P. P. De Deyn (2003) rightfully argue that the observed behavior (similarity judgments) does not tell us the source (cause) of the differences between the 2 groups. Rather, the focus of the study should be placed more on finding the ways the 2 groups are different. They also point out various methodological problems in some of the previous attempts to characterize the nature of the differences. Further methodological issues in G. Storms et al.'s study are examined. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Intramolecular triplet energy migration in poly(2-vinylnaphthalene) and poly(naphthylalkyl methacrylate)s in solid solution: Effects of side chain length

Summary The effect of side chain length on intramolecular triplet energy migration of naphthalene containing polymers was investigated by a delayed fluorescence (DF) spectroscopy for the solid solution of the polymers. The degree of triplet energy migration depends strongly on whether the chromophores are directly attached to the main chain or not.     

Distribution of higher-order structures in injection-molded polypropylenes

Flexural test specimens were injection-molded from six homoisotactic polypropylenes with MFI = 0.49-25.1 dg/min under cylinder temperatures of 200-320°C. Distributions in the flow direction of higher-order structures such as crystallinity X_c, thickness of skin layer, a*-axis-oriented component fraction [A*], and crystalline orientation functions and distributions in the thickness direction of higher-order structures such as X_c, β-crystal contents, [A*], and crystalline orientation functions were studied. These higher-order structures are inhomogeneous in the flow and thickness directions, which strongly influences the product properties such as mechanical and thermal properties. Molecular orientation process in injection molding was theoretically analyzed from a viewpoint of growth of recoverable shear strain at the gate and its relaxation in the cavity, which could considerably well explain the variations in the flow and thickness directions of the quantities such as thickness of the skin layer and crystalline orientation functions which express the degree of molecular orientation.     

Preparation and Luminescence Spectra of Calcium- and Rare-Earth (R = Eu, Tb, and Pr)-Codoped α-SiAlON Ceramics

Rare-earth-doped oxynitride or nitride compounds have been reported to be luminescent and may then serve as new phosphors with good thermal and chemical stabilities. In this work, we report the photoluminescence (PL) spectra of europium-, terbium-, and praseodymium-doped Ca-α-SiAlON ceramics. The highly dense ceramics were prepared by hot pressing at 1750°C for 1 h under 20 MPa in a nitrogen atmosphere. Europium-doped Ca-α-SiAlON displayed a single broad emission band peaking at λ= 550–590 nm depending on the europium concentration. The emission bands in the spectra of europium-doped Ca-α-SiAlONs were assigned to the allowed transition of Eu²⁺ from the lowest crystal field component of 4 f ⁶5 d to ⁸S_7/2 (4 f ⁷) ground-state level. The emission spectra of terbium- and praseodymium-doped Ca-α-SiAlON ceramics both consisted of several sharp lines, which were attributed to the ⁵D₄→⁷F _j ( j = 3, 4, 5, 6) transitions of Tb³⁺ and ³P₀→³H _j ( j = 3, 4, 5) transitions of Pr³⁺, respectively. In particular, the terbium-doped α-SiAlON ceramics showed a strong green emission among these phosphors.