Coprocessor design for multilayer surface-mounted PCB routing

The authors present the issues involved in the design of a special-purpose processing array system, called HAM, which accelerates computationally intensive wire routing tasks. It is especially suited for double-sided surface-mounted boards, which require complex three-dimensional search operations over multiple wiring planes. The novel features of the design include a hexagonal interconnection scheme to improve workload distributions during multilayer concurrent search operations and the VLSI custom design of the processors. Particular emphasis has been placed on the demands of maze routing. A cell-address propagation scheme, which is quite different from the traditional grid-coordinate approach, is discussed. It provides rapid lookup of pertinent routing information and can be extended to any distributed memory multiprocessor system. A global pipelining scheme of cell updates and expands is discussed. Experimental results are presented relating the speedup to various criteria for two different modes of parallel wave propagation     

Microstructure and Properties of Spark Plasma-Sintered ZrO2–ZrB2 Nanoceramic Composites

In a recent work, ¹ we have reported the optimization of the spark plasma sintering (SPS) parameters to obtain dense nanostructured 3Y-TZP ceramics. Following this, the present work attempts to answer some specific issues: (a) whether ZrO₂-based composites with ZrB₂ reinforcements can be densified under the optimal SPS conditions for TZP matrix densification (b) whether improved hardness can be obtained in the composites, when 30 vol% ZrB₂ is incorporated and (c) whether the toughness can be tailored by varying the ZrO₂–matrix stabilization as well as retaining finer ZrO₂ grains. In the present contribution, the SPS experiments are carried out at 1200°C for 5 min under vacuum at a heating rate of 600 K/min. The SPS processing route enables retaining of the finer t -ZrO₂ grains (100–300 nm) and the ZrO₂–ZrB₂ composite developed exhibits optimum hardness up to 14 GPa. Careful analysis of the indentation data provides a range of toughness values in the composites (up to 11 MPa·m^1/2), based on Y₂O₃ stabilization in the ZrO₂ matrix. The influence of varying yttria content, t -ZrO₂ transformability, and microstructure on the properties obtained is discussed. In addition to active contribution from the transformation-toughening mechanism, crack deflection by hard second phase brings about appreciable increment in the toughness of the nanocomposites.     

Preparation and Kinetic Considerations for the Dissolution of Cr‐substituted Iron Oxides in Reductive‐complexing Formulations

The dissolution rate coefficients of Cr‐substituted (0‐20 at.% Cr) iron oxides viz. hematite and magnetite were determined by using an inverse cubic rate (ICR) law applicable for spherical particles as well as by a general kinetic equation (GKE) applicable for polydispersed particles. An attempt is made to compare both the treatments for different kinds of dissolution profiles obtained by employing oxides with narrow particle size distribution in V(II)‐EDTA and citric acid‐EDTA‐ascorbic acid formulations at 353±5K. The dissolution profiles could be classified into three types based on the nature of oxide and formulations. It is observed that both ICR and GKE treat the dissolution course as a function of decrease in fraction of undissolved mass, m/m₀. The dissolution rate coefficients determined by ICR and GKE have shown the similar trend of decrease with increasing Cr content of the oxides and was ascribed to lattice stabilization.     

Influence of 2,3-Dihydroxyflavanone on Corrosion Inhibition of Mild Steel in Acidic Medium

The inhibition effect of 2,3-dihydroxyflavone on the corrosion of mild steel in 100-600 ppm aqueous hydrochloric acid solution has been investigated by weight loss and electrochemical impedance spectroscopy. The corrosion inhibition efficiency increases with increasing concentration and time. The effect of temperature on the corrosion behavior of mild steel in 1 M HCl with addition of inhibitor was studied at the temperature range of 300-330 K. UV-Vis, FTIR, and surface analysis (SEM) was also carried out to establish the corrosion inhibitive property of this inhibitor in HCl solution. The adsorption of this inhibitor on the mild steel surface obeys the Langmuir adsorption isotherm. Electrochemical studies reveal that the inhibitor is a cathodic type.     

Determination of mechanical properties of Al–Mg alloys dissimilar friction stir welded interface by indentation methods

A series of friction stir welds was produced between heat treated Al–Mg–Si and strain hardened Mg–Al–Zn alloy sheets. Weld evaluation by transverse tensile testing showed a wide range of strengths and all the failures occurred along the weld interface. The formation of intermetallic compounds in the weld joints was investigated by X-ray diffraction, scanning electron microscopy imaging, and elemental analysis techniques. Micro and nanoindentation characterization methods were used to evaluate the mechanical properties at the interface, including the fracture toughness. The fracture toughness measurements by a Vickers indenter introduced Palmqvist type cracks at all four corners of the indents and cube corner indenter resulted in the intermetallic chipping. The fracture toughness (K _IC) calculation by both the micro and nanoindentation methods showed very low values, which is the primary reason for the brittle failure of the dissimilar weld joints and concomitant low tensile strengths.     

The Effect of Trace Elements on the Cooling Curves,Microstructure and Mechanical Properties of Eutectic Aluminium-Silicon Alloy

Abstract

The effect of trace elements, used for modification, on the cooling curves obtained during solidification, microstructure and mechanical properties of eutectic aluminium-silicon alloy was investigated. The results of this study indicate the following: 1 The addition of sodium or sodium plus strontium or antimony modifies the eutectic silicon while the addition of sulphur does not alter the microstructure.

2 Those elements which modify the eutectic-silicon, lower the eutectic solidification temperature, while those elements which do not bring about modification, do not alter the eutectic solidification temperature.

3 The addition of those elements which modify the eutectic aluminium-silicon alloy, viz., sodium or sodium plus strontium or antimony improves the UTS and percentage elongation. The addition of titanium to eutectic aluminium-silicon alloy containing these trace elements improves the UTS and percentage elongation to a further extent. Among the various trace elements added to eutectic aluminium-silicon alloy, the addition of sodium plus titanium improves the UTS and percentage elongation to the maximum extent.

     

Rheological behaviour of emulsions of avocado and watermelon oils during storage

Rheological properties of emulsions made out of avocado pulp and watermelon seed oils with whey protein concentrate were determined during different storage periods. The oils, as well as the emulsions behaved like non-Newtonian liquids, having shear-thinning characteristics. Both oils showed moderate shear-thinning characteristics as the flow behaviour indices were between 0.86 and 0.88. The shear-rate/shear-stress data could be adequately fitted (r = 0.997–0.999) to a common rheological equation, e.g. the power-law model. Avocado pulp oil was markedly more viscous than was watermelon seed oil which was also evident from the higher apparent viscosity and consistency index values.