Pressure-induced transparency of MgO,Al2O3, AlN,and cBN ceramics at room temperature

The in situ axial X-ray diffraction patterns of four ceramic powder samples (MgO, Al₂O₃, AlN, and cBN) that were compressed in a diamond anvil cell under uniaxial non-hydrostatic conditions were recorded. The microscopic deviatoric stress as a function of the pressure was determined from the X-ray diffraction peak broadening analysis: the curves increased approximately linearly with the pressure at the initial compression stage and then levelled off under further compression. Pressure-induced transparency was observed in all of the samples under compression, and the pressure at the turning point on the curves of the microscopic deviatoric stress versus pressure corresponded to the pressure at which the samples became transparent. Analysis of the microstructural features of the pressure-induced transparent samples indicated that the compression caused the grains to fracture, and the broken grains bonded with each other. We demonstrated that the ceramics’ pressure-induced transparency was a process during which the grains were squeezed and broken, the pores were close between the grains, and the broken grains were re-bonded under compression.     

A mini review on two-dimensional nanomaterial assembly

Two-dimensional (2D) nanomaterials have attracted a great deal of attention since the discovery of graphene in 2004, due to their intriguing physicochemical properties and wide-ranging applications in catalysis, energy-related devices, electronics and optoelectronics. To maximize the potential of 2D nanomaterials for their technological applications, controlled assembly of 2D nanobulding blocks into integrated systems is critically needed. This mini review summarizes the reported strategies of 2D materials-based assembly into integrated functional nanostructures, from in-situ assembly method to post-synthesis assembly. The applications of 2D assembled integrated structures are also covered, especially in the areas of energy, electronics and sensing, and we conclude with discussion on the remaining challenges and potential directions in this emerging field.

     

儿童用品TBT通报数据可视化预警研究

探索采用数据可视化技术分析儿童用品TBT通报数据,以可视化图形图像呈现通报热点并揭示趋势信息,提出对策与建议,助力为儿童用品产业升级、TBT预警数据分析和信息传播工作提供新思路,提高中小企业的国外市场准入机会。     

荷电细水雾对管道瓦斯爆炸超压的影响规律研究

为了研究荷电细水雾对瓦斯爆炸超压的影响规律和机理,采用小尺寸管道模拟瓦斯爆炸,研究不同荷电电压作用下的瓦斯爆炸超压和平均压升速率,以及不同雾通量作用下的瓦斯爆炸超压.结果表明:随着荷电电压的升高,瓦斯爆炸超压和平均压升速率受到明显的抑制;随着雾通量的增加,瓦斯爆炸超压明显降低.在实验条件下,和普通细水雾相比,当雾通量为4L、荷电电压为8kV时,瓦斯爆炸超压峰值降低10.798kPa,降幅达49.78%;平均压升速率峰值降低180.468kPa/s,降幅达49.90%.     

文献计量视角下健康人力资本研究动态分析

通过文献计量方法从样本选取、研究动态分析、主题分布三方面对健康人力资本发展现状及热点问题进行总结.研究结果表明,自2004年开始该领域所属学科种类和期刊源日益丰富,并形成合著度较高的核心作者群体,健康人力资本研究成为人力资本领域的研究热点,健康人力资本与经济增长或收入的关系、健康人力资本指标体系的构建和居民健康人力资本收入效应的测算等问题都成为当前和未来的研究重点.     

开关磁阻直线电机的设计及其推力优化

设计了一种开关磁阻直线电机,使用JMAG软件对其进行了仿真和优化。进行了推力公式的推导,研究了导通顺序和初始位置对电机推力的影响,并分析了三种典型情况的磁力线分布。对电机的定子和动子的齿部和轭部高度、宽度及铁耗进行仿真优化,得出了最优参数。将有取向硅钢应用于该电机,研究了推力与轧制角的关系,并与使用普通硅钢的开关磁阻直线电机进行了对比,推力有一定提升。提出在动子齿部开切向槽的方案,结果表明,开切向槽对推力的影响较小,并能显著减小推力波动。     

基于Q-learning的不确定环境BDI Agent最优策略规划研究

BDI模型能够很好地解决在特定环境下的Agent的推理和决策问题,但在动态和不确定环境下缺少决策和学习的能力。强化学习解决了Agent在未知环境下的决策问题,却缺少BDI模型中的规则描述和逻辑推理。针对BDI在未知和动态环境下的策略规划问题,提出基于强化学习Q-learning算法来实现BDI Agent学习和规划的方法,并针对BDI的实现模型ASL的决策机制做出了改进,最后在ASL的仿真平台Jason上建立了迷宫的仿真,仿真实验表明,在加入Q-learning学习机制后的新的ASL系统中,Agent在不确定环境下依然可以完成任务。