Characterization of the Residence Time Distribution in Spray Dryers

In this work it is presented a study on the residence time distribution (RTD) of particles in a co-current pilot-plant spray dryer operated with a rotary atomization system. A nuclear technique is applied to investigate the RTD responses of spray dryers. The methodology is based on the injection of a radioisotope tracer in the feed stream followed by the monitoring of its concentration at the outlet stream. The experiments were performed during the drying of aqueous suspensions of gadolinium oxide. The RTD responses obtained experimentally presented good reproducibility, indicating that the technique applied is well suited to investigating fluid-dynamics of spray dryers. In addition to the experimental investigation, a mathematical model was used to describe the RTD experimental curves.     

Clarification of a wheat straw‐derived medium with ion‐exchange resins for xylitol crystallization

BACKGROUND: Xylitol bioproduction from lignocellulosic residues comprises hydrolysis of the hemicellulose, detoxification of the hydrolysate, bioconversion of the xylose, and recovery of xylitol from the fermented hydrolysate. There are relatively few reports on xylitol recovery from fermented media. In the present study, ion‐exchange resins were used to clarify a fermented wheat straw hemicellulosic hydrolysate, which was then vacuum‐concentrated and submitted to cooling in the presence of ethanol for xylitol crystallization. RESULTS: Sequential adsorption into two anion‐exchange resins (A‐860S and A‐500PS) promoted considerable reductions in the content of soluble by‐products (up to 97.5%) and in medium coloration (99.5%). Vacuum concentration led to a dark‐colored viscous solution that inhibited xylitol crystallization. This inhibition could be overcome by mixing the concentrated medium with a commercial xylitol solution. Such a strategy led to xylitol crystals with up to 95.9% purity. The crystallization yield (43.5%) was close to that observed when using commercial xylitol solution (51.4%). CONCLUSION: The experimental data demonstrate the feasibility of using ion‐exchange resins followed by cooling in the presence of ethanol as a strategy to promote the fast recovery and purification of xylitol from hemicellulose‐derived fermentation media. Copyright © 2008 Society of Chemical Industry     

Detection of anti-HIV-1 IgG antibodies in whole saliva by GACELISA and Western blot assays

The present study, based on 158 HIV seropositives and 167 HIV seronegatives, demonstrates that saliva collected with the Omni-SAL device and tested with GACELISA (an IgG antibody capture ELISA) is an effective non-invasive alternative to serum for anti-HIV IgG antibody screening. The study also shows that a conventional serum Western blot kit can be used, with slight modifications, for confirmatory testing of saliva specimens. Collecting saliva with the Omni-SAL device had a very good acceptance rate among Tanzanian subjects, and although this diagnostic method is not yet known by the general public, 65% of the study participants preferred to give saliva instead of blood for HIV testing.     

Parallel quicksort

A parallel version of quicksort on a CRCW PRAM is developed. The algorithm uses n processors and a linear space to sort n keys in the expected time O(log n) with large probability.     

Enhancement mode InP MISFET's with sulfide passivation andphoto-CVD grown P3N5 gate insulators

High performance enhancement mode InP MISFET's have been successfully fabricated by using the sulfide passivation for lower interface states and with photo-CVD grown P₃N₅ film used as gate insulator. The MISFET's thus fabricated exhibited exhibited pinch-off behavior with essentially no hysteresis. Furthermore the device showed a superior stability of drain current. Specifically under the gate bias of 2 V for 10⁴ seconds the room temperature drain current was shown to reduce from the initial value merely by 2.9% at the drain voltage of 4 V. The effective electron mobility and extrinsic transconductance are found to be about 2300 cm ²/V·s and 2.7 mS/mm, respectively. The capacitance-voltage characteristics of the sulfide passivated InP MIS diodes show little hysteresis and the minimum density of interface trap states as low as 2.6×10¹⁴/cm² eV has been attained     

Biliary obstruction due to duodenojejunal intussusception in Peutz-Jeghers syndrome

We reported an operative case of bilateral coronary artery fistulae to pulmonary artery associated with a giant saccular aneurysm, the largest of which measured 30 x 30 mm. The patient was a 75 year old female who had anginal pain due to coronary steal phenomenon. A continuous murmur was detected. After establishing total cardiopulmonary bypass, two distal orifices of the fistula connected to the main pulmonary artery were closed with 5-0 polypropylene plegeted sutures. Aneurysmorrhaphy was then performed for giant saccular aneurysm. Postoperative course was uneventful.     

RF antenna analysis with the ICANT code

The ICANT code computes self-consistently the surface current distribution on a 3D antenna model radiating in a plasma or vacuum and has been used to analyze the coupling properties of various antenna models. In this work it is used to assess near-fields generated by different versions of the TCABR (Tokamak Chauffage Alfvén wave heating experiment in Brazil) antenna as well as coupling properties of the TEXTOR tokamak in Forshungszentrum Jülich. Two different strap models planned for the TCABR antenna are shown to be practically equivalent in terms of maximum electric field. Textor coupling calculations are close to experimental values.     

Pressure effects on flow and fracture of Be-Al alloys

The flow and fracture behavior of Be-Al alloys were determined in tension with different levels of superimposed pressure. The Be-Al alloys were prepared by Brush Wellman, Inc. (Cleveland, OH) from prealloyed powders processed to either a hot isostatically pressed (“hipped”) or cold isostatically pressed and extruded condition. Significant effects of pressure on both the flow and ductility have been observed at room temperature, with implications on the formability of these materials. The effects of changes in processing conditions and stress state on the flow and fracture behavior are summarized in addition to both optical and scanning electron microscopy (SEM) examination of the fracture surfaces. Separate other studies on the alloy constituents (e.g., Al and Be) are also reported. The results are also compared to previous works on monolithic materials and composites tested with high pressure.