The apolipoprotein E allele epsilon 4 is overrepresented in patients with the Lewy body variant of Alzheimer's disease

We determined apolipoprotein E (ApoE) genotypes in 122 autopsied demented patients. The frequency of the ApoE epsilon 4 allele was 39.6% in Alzheimer's disease (AD), 29.0% in the Lewy body variant of AD (LBV), and 6.25% in diffuse Lewy body disease. For AD and LBV patients, the epsilon 4 frequency was significantly higher than that reported in nondemented controls (10 to 15%). Therefore, LBV and AD share ApoE epsilon 4 as a genetic risk factor, providing further evidence that these conditions overlap.     

Parallel path consistency

Filtering algorithms are well accepted as a means of speeding up the solution of the consistent labeling problem (CLP). Despite the fact that path consistency does a better job of filtering than arc consistency, AC is still the preferred technique because it has a much lower time complexity. We are implementing parallel path consistency algorithms on multiprocessors and comparing their performance to the best sequential and parallel arc consistency algorithms.^(1,2) (See also work by Kerethoet al. ⁽³⁾ and Kasif⁽⁴⁾) Preliminary work has shown linear performance increases for parallelized path consistency and also shown that in many cases performance is significantly better than the theoretical worst case. These two results lead us to believe that parallel path consistency may be a superior filtering technique. Finally, we have implemented path consistency as an outer product computation and have obtained good results (e.g., linear speedup on a 64K-node Connection Machine 2).     

重馏分油加氢脱氮反应动力学模型的研究

简要地介绍了一些典型的模型氮化物的ＨＤＮ反应规律。根据胜利ＶＧＯ在３７２２Ｂ催化剂上的大量ＨＤＮ实验数据，提出了如下的ＨＤＮ基本反应动力学方程：ｄＣＮｄｔ＝－ｋ１＋Ｋ＊ＣＮＣＮＰＨ２为了扩大上式的应用范围，详细分析了各种因素（如原料油种类和馏程及Ｈ２Ｓ等）对ＨＤＮ的影响，并开发了相应的经验关联式，从而得到了一个较完整的馏分油ＨＤＮ反应动力学模型。验证实验表明，该模型是成功的。     

A new boundary-layer wind tunnel at the Danish Maritime Institute

The paper describes a new boundary-layer wind tunnel at the Danish Maritime Institute in Lyngby. The wind tunnel is of the open-circuit type and is integrated into a building raised for the purpose. The design was constrained by the need to provide a simulation of the atmospheric boundary layer (without thermal stratification) and alternatively a uniform flow without excessive turbulence.The wind tunnel has a working section of principal dimensions: length 20.8 m, width 2.6 m and height 1.8 m (adjustable from 1.8 to 2.3 m). The maximum wind speed in the working section when empty is about 26 m s^?1.Data acquisition, analysis and instrumentation in relation to the new wind tunnel are discussed and, finally, an example of a simulated natural wind is presented.     

2 cm long monolithic multisection laser for active modelocking at 2.2 GHz

A 2 cm long three-contact multisection laser has been fabricated for modelocking at very low repetition rates. Active modelocking yields 8.0-12.3 ps pulses at 2.2, 4.3 and 6.5 GHz corresponding to the fundamental, first, and second harmonics of the cavity resonance frequency. This device demonstrates the feasibility of fabricating monolithic pulse sources operating at rates as low as the OC-48 Sonet transmission rate (2.488 Gbit/s).<>     

Intravitreal tolerance of a new perfluorocarbon vitreous replacement, Multifluor APF-144

OBJECTIVE: To evaluate the intravitreal tolerance of a new perfluorocarbon vitreous replacement, Multifluor APF-144 (perfluorotetramethylcyclohexane). DESIGN: Ten New Zealand albino rabbits (one eye from each) underwent vitrectomy. The vitreous was replaced in five eyes with Multifluor APF-144 and in five eyes with saline (control group). OUTCOME MEASURES: Appearance on indirect ophthalmoscopy, electroretinography recordings before and 2, 4 and 8 weeks after vitrectomy, findings on electron and light microscopy at 8 weeks. RESULTS: Endophthalmitis did not develop in any of the eyes. There was no significant change in electroretinography values for the experimental eyes after vitrectomy. No evidence of retinal toxicity was found on light or electron microscopic examination. CONCLUSIONS: Multifluor APF-144 shows promise as a short-term postoperative retinal tamponading agent.     

A nonlinear operator-based speech feature analysis method withapplication to vocal fold pathology assessment

Traditional speech processing methods for laryngeal pathology assessment assume linear speech production with measures derived from an estimated glottal flow waveform. They normally require the speaker to achieve complete glottal closure, which for many vocal fold pathologies cannot be accomplished. To address this issue, a nonlinear signal processing approach is proposed which does not require direct glottal flow waveform estimation. This technique is motivated by earlier studies of airflow characterization for human speech production. The proposed nonlinear approach employs a differential Teager energy operator and the energy separation algorithm to obtain formant AM and FM modulations from filtered speech recordings. A new speech measure is proposed based on parameterization of the autocorrelation envelope of the AM response. This approach is shown to achieve impressive detection performance for a set of muscular tension dysphonias. Unlike flow characterization using numerical solutions of Navier-Stokes equations, this method is extremely computationally attractive, requiring only a small time window of speech samples. The new noninvasive method shows that a fast, effective digital speech processing technique can be developed for vocal fold pathology assessment without the need for direct glottal flow estimation or complete glottal closure by the speaker. The proposed method also confirms that alternative nonlinear methods can begin to address the limitations of previous linear approaches for speech pathology assessment     

Prediction of fire classification for wood based products. A multivariate statistical approach based on the cone calorimeter

Wood has long traditions as a building material, and is often used in construction elements, and as interior and exterior surfaces in the Nordic countries. In most applications, there are reaction to fire requirements to products used as surfaces, e.g. in escape routes and larger public spaces. Most wood products will therefore have to be treated with fire retardant (FR) agents to fulfil the strict requirements to properties connected to heat release and flame spread. Unfortunately, FR agents usually also increase the smoke production, as they cause a more incomplete combustion of the wood. The wood product manufacturers seek to find the optimal amount of FR additives where both heat release and smoke production in the classifying test are within the requirements given in the building regulations. This paper describes models for prediction of the European reaction to fire classes of wood products. The models are based on multivariate statistical analysis, and use test results from the cone calorimeter test as input. The presented models are, with very good precision, able to predict which Euroclass and additional smoke class a wood based product would obtain if it were to be tested in the single burning item test. Copyright © 2006 John Wiley & Sons, Ltd.