Effect of Temperature on Reliability Issues of Ferroelectric Dopant Segregated Schottky Barrier Tunnel Field Effect Transistor (Fe DS-SBTFET)

This paper addresses reliability issues associated with temperature of Ferroelectric Dopant Segregated Schottky Barrier Tunnel Field Effect Transistor (Fe DS-SBTFET). The simulated results are compared with Dopant Segregated Schottky Barrier TFET (DS-SBTFET). This is achieved by varying the operating temperature from 300 to 500 K. DC parameters such as I_ON/I_OFF ratio, drain current characteristics and subthreshold swing (SS) for a range of temperature have been highlighted. Moreover, the influence of temperature on various RF figure of merits such as gate capacitance (C_GG), intrinsic delay, cutoff frequency (f_T) etc. have been investigated. The device linearity has been analyzed by considering the effect of temperature variation on linearity parameters like g_m2, g_m3, 1-dB compression point, VIP₂, VIP₃ and IIP₃. The device characteristics get upgraded by the increase in cut-off frequency and reduction in intrinsic delay at elevated temperature.

     

Impact of adhesive ingredients on adhesion between rubber and brass-plated steel wire in tire

Proficiency on underlying mechanism of rubber-metal adhesion has been increased significantly in the last few decades. Researchers have investigated the effect of various ingredients, such as hexamethoxymethyl melamine, resorcinol, cobalt stearate, and silica, on rubber-metal interface. The role of each ingredient on rubber-metal interfacial adhesion is still a subject of scrutiny. In this article, a typical belt skim compound of truck radial tire is selected and the effect of each adhesive ingredient on adhesion strength is explored. Out of these ingredients, the effect of cobalt stearate is found noteworthy. It has improved adhesion strength by 12% (without aging) and by 11% (humid-aged), respectively, over control compound. For detailed understanding of the effect of cobalt stearate on adhesion, scanning electron microscopy and energy dispersive spectroscopy are utilized to ascertain the rubber coverage and distribution of elements. X-ray photoelectron spectroscopy results helped us to understand the impact of Cu_XS layer depth on rubber-metal adhesion. The depth profile of the Cu_XS layer was found to be one of the dominant factors of rubber-metal adhesion retention. Thus, this study has made an attempt to find the impact of different adhesive ingredients on the formation of Cu_XS layer depth at rubber-metal interface and establish a correlation with adhesion strength simultaneously.     

Prolonged tamoxifen exposure selects a breast cancer cell clone that is stable in vitro and in vivo

The effects of long-term tamoxifen exposure on cell growth and cell cycle kinetics were compared between oestrogen receptor (ER)-positive (MCF-7) and ER-negative (MDA-MB-231) cell lines. In the MCF-7 cell line, prolonged tamoxifen exposure (0.5 mumol/l for > 100 days) blocked cells in G0-G1 of the cell cycle, and slowed the doubling time of cells from 30 to 59 h. These effects corresponded to an increase in the cellular accumulation of tamoxifen over time [mean area under concentration curve (AUC) = 77.92 mumoles/10(6)/cells/day]. In contrast, in the MDA-MB-231 cell line, long-term tamoxifen exposure had no obvious effect on the doubling time, and reduced cellular tamoxifen accumulation (mean AUC = 50.50 mumoles/10(6)/cells/day) compared to the MCF-7 cells. Flow cytometric analysis of MDA-MB-231 cells demonstrated that a new tetraploid clone emerged following 56 days of tamoxifen exposure. Inoculation of the MDA-MB-231 tetraploid clone and MDA-MB-231 wildtype cells into the opposite flanks of athymic nude mice resulted in the rapid growth of tetraploid tumours. The tetraploid tumours maintained their ploidy following tamoxifen treatment for nine consecutive serial transplantations. Histological examination of the fifth transplant generation xenografts revealed that the tetraploid tumour had a 25-30 times greater mass, area of haemorrhage and necrosis, a slightly higher mitotic index and was more anaplastic than the control neoplasm. The control wildtype MDA-MB-231 tumours maintained a stable ploidy following tamoxifen treatment until the eighth and ninth transplantation, when a tetraploid population appeared, suggesting that tamoxifen treatment may select for this clone in vivo. These studies suggest that prolonged tamoxifen exposure may select for new, stable, fast growing cell clones in vitro as well as in vivo.     

PES News

This paper presents a new method for the generation of a reference voltage for a dynamic voltage restorer (DVR). These voltages, when injected in series with a distribution feeder by a voltage source inverter, can tightly regulate the voltage at the load terminal against imbalance or harmonics in the source side. It is stipulated that the DVR does not supply any real power in the steady state. The reference voltage generation scheme is validated through digital computer simulation studies.     

Cavitation in Superfluid Helium Possibly Arising from Penning Ionization of Dimers

We have perforated a series of experiments to study cavitation in superfluid helium into which electrons are injected by field-emission from a sharp tip. The injected electrons force open small cavities in the liquid (“electron bubble”). These objects explode at a critical negative pressure P _c, and in previous experiments we have studied the cavitation that resugts from these explosions. In the present experiments we have detected cavitation events that occur before a negative pressure as large as P _c is reached. We suggest that these events may arise from a process in which two neutral helium dimers interact and an electron is injected into the liquid through Penning ionization.     

Direct synthesis of copper faujasite

Copper containing faujasite has been successfully prepared for the first time using a direct synthesis method. Faujasite type zeolite can be prepared in the presence of copper species by tuning the synthesis conditions. Ammonium hydroxide was used to form a copper complex that was later mixed with the reacting gel. Sodium is required to obtain copper faujasite. The complete elimination of sodium ions from the starting gel produces amorphous material. Crystallization took place at 358 K for 11 days. Crystallization temperature of 373 K produces ANA type zeolite as an impurity. Increasing by two times the amount of copper complex added to the reacting gel increases the crystallization time of Cu-FAU from 11 to 20 days (the crystallization rate decreases). The copper containing faujasite obtained was characterized by XRD, FESEM, EDX, EPR, FT-IR, TPR, and BET. According to the XRD pattern only FAU type zeolite was obtained. According to TPR experiments, the reduction temperature for Cu²⁺ ions present in Cu-FAU prepared by direct synthesis was 70 K more than for Cu-FAU prepared by ion-exchange. This difference can be due to the different location of the copper ions in the supercages or in the sodalite cages of the faujasite.