利用5A284型铣齿机加工转盘螺旋锥齿轮探讨

利用引进设备5A284苏联铣齿机加工石油钻机转盘螺旋锥齿轮，建立计算程序并进行调整计算，详述了遇到的问题及解决方法，使所加工的锥齿轮质量良好。     

水热法制备ZrO_2纳米微晶及对乙醇和丁烷气敏性研究

用水热法制备 Zr O2 纳米微晶的平均尺寸为直径 5 nm,长 7.5 nm。由 X射线衍射确认晶相为单斜相。并对其形状和大小进行了透射电镜和激光散射分析 ,结果表明 Zr O2 纳米粒子在水溶液中存在软团聚 ,团聚体平均尺寸约 90 nm。着重研究了 Zr O2 纳米微晶对乙醇及丁烷的气敏性能 ,结果表明用纳米级 Zr O2 粒子制备的气敏元件对乙醇和丁烷有好的气敏性。并且随着纳米粒子尺寸降低 ,对气体敏感性增强     

Decarburization rate of RH refining for ultra low carbon steel

The decarburization behaviors of ultra low carbon steel in a 210-t RH vacuum degasser were investigated under practical operating conditions.According to the apparent decarburization rate constant (KC) calculated by the carbon content in the samples taken from the hot melt in a ladle at an interval of 1-2 min,it is observed that the total decarburization reaction period in RH can be divided into the quick decarburization period and the stagnant decarburization period,which is quite different from the tradit...     

Effects of Cu on Microstructures,Mechanical, and Magnetic Properties of Fe–Ni–P Alloys Fabricated by Liquid Phase Sintering

The Fe–Ni–P–Cu alloys with different copper content (0, 0.5, 1, and 2 wt%) are fabricated by liquid phase sintering (LPS) at 950 °C. The nano‐Cu powder is mechanically mixed for 90 min with Fe–Ni–P composite powder using the ethanol as the medium. The microstructure, microhardness and compressive properties of Fe–Ni–P–Cu alloys are investigated. The results indicate that the copper is beneficial to improve the mechanical properties of sintered specimens. The sample contains a small amount of γ‐(Fe, Ni) phase when the copper content is 1 wt%, which results in its the highest compressive yield strength (948.1 MPa). The highest microhardness of 371 HV is accessible in Fe–Ni–P–Cu alloy with 2 wt% Cu. The fracture surface analysis indicates that sintered specimens with Cu addition exhibit a typical intergranular mode.     

网站新闻管理系统设计与实现

结合ASP.NET和ADO.NET技术开发的网站新闻管理系统,实现了网站新闻的动态管理,克服了以前ASP开发的新闻静态管理的缺陷,使得对信息的处理更加及时、高效,提高了工作效率     

Convolutional neural network feature maps selection based on LDA

Convolutional neural network (CNN), as widely applied to vision and speech, has developed lager and lager network size in last few years. In this paper, we propose a CNN feature maps selection method which can simplify CNN structure on the premise of stabilize the classifier performance. Our approach aims to cut the feature map number of the last subsampling layer and achieves shortest runtime on the basis of Linear Discriminant Analysis (LDA). We rebuild feature maps selection formula based on the between-class scatter matrix and within-class scatter matrix, because LDA can lead to information loss in the dimension-reduction process. Our experiments measure on two standard datasets and a dataset made by ourselves. According to the separability value of each feature map, we suggest the least number of feature maps which can keep the classifier performance. Furthermore, we prove that separability value is an effective indicator for reference to select feature maps.     

国内野生观赏植物研究现状综述与展望

文章对近年来野生观赏植物调查研究的现状进行了综述,并在此基础上,从引种驯化和园林绿化两个方面,对野生观赏植物的开发利用进行了总结归纳和展望。     

氢氟酸-硝酸体系中Ti-6Al-4V的腐蚀加工溶解特征

利用E-t曲线、动电位极化曲线研究了氢氟酸-硝酸体系中溶液主体成分、温度对Ti-6Al-4V腐蚀加工溶解行为和特征的影响,通过测试阳极与阴极反应动力学揭示钛合金腐蚀加工动力学规律。研究结果表明,在该溶液体系中钛合金的腐蚀加工是侵蚀-溶解-钝化循环往复的过程,硝酸的钝化作用与氢氟酸的溶解作用同时存在,当钝化膜的生成速度和钛基体的溶解速度达到动态平衡时,腐蚀速度处于相对稳定的状态。腐蚀加工初期阶段氢氟酸浓度会影响钛合金表面氧化膜的破坏,浓度较低时,氧化膜较难破坏,自腐蚀电位正移;浓度较高时,氧化膜容易被腐蚀溶解,自腐蚀电位负移。氢氟酸浓度和温度增加,反应活化能减少,腐蚀溶解加剧。氢氟酸浓度较低时,温度对加工速度的影响占主导地位;浓度增加到80 m L/L,温度的影响减弱,氢氟酸起主要作用。硝酸的钝化作用在减少总体腐蚀速度的同时可有效改善微观表面的凹凸不平,使微观表面趋于平整。     

MAX相Ti3SiC2管材在高温高压水和过热蒸汽中的腐蚀行为

MAX相材料有作为事故容错燃料(accident tolerant fuel,ATF)包壳材料的潜力,为了全面了解MAX相材料在模拟正常工况下的腐蚀行为,使用基体为Ti₃SiC₂的MAX相陶瓷管材于400℃/10.3 MPa过热蒸气,360℃/18.6 MPa去离子水、3.5μL/L Li+1000μL/L B溶液和70μL/L Li溶液4种不同的水化学条件中进行腐蚀试验,采用XRD、SEM和FIB/TEM观察分析腐蚀前后样品的显微组织、晶体结构和成分。结果表明,Ti₃SiC₂管材在4种条件下的腐蚀速率均远高于参比Zr-4合金,腐蚀后主要检测到腐蚀产物TiO₂,且其表面疏松多孔,未形成保护性的氧化膜。