Engineering egress data considering pedestrians with reduced mobility

To quantify the evacuation process, evacuation practitioners use engineering egress data describing the occupant movement characteristics. These data are typically based to young and fit populations. However, the movement abilities of occupants who might be involved in evacuations are becoming more variable—with the building populations of today typically including increasing numbers of individuals: with impairments or who are otherwise elderly or generally less mobile. Thus, there will be an increasing proportion of building occupants with reduced ability to egress. For safe evacuation, there is therefore a need to provide valid engineering egress data considering pedestrians with disabilities. Gwynne and Boyce recently compiled a series of data sets related to the evacuation process to support practitioner activities in the chapter Engineering Data in the SFPE Handbook of Fire Protection Engineering. This paper supplements these data sets by providing information on and presenting data obtained from additional research related to the premovement and horizontal movement of participants with physical‐, cognitive‐, or age‐related disabilities. The aim is to provide an overview of currently available data sets related to, and key factors affecting the egress performance of, mixed ability populations which could be used to guide fire safety engineering decisions in the context of building design.     

Proton-Detected Solid-State NMR of the Cell-Free Synthesized α-Helical Transmembrane Protein NS4B from Hepatitis C Virus

Proton-detected 100 kHz magic-angle-spinning (MAS) solid-state NMR is an emerging analysis method for proteins with only hundreds of microgram quantities, and thus allows structural investigation of eukaryotic membrane proteins. This is the case for the cell-free synthesized hepatitis C virus (HCV) nonstructural membrane protein 4B (NS4B). We demonstrate NS4B sample optimization using fast reconstitution schemes that enable lipid-environment screening directly by NMR. 2D spectra and relaxation properties guide the choice of the best sample preparation to record 2D ¹H-detected ¹H,¹⁵N and 3D ¹H,¹³C,¹⁵N correlation experiments with linewidths and sensitivity suitable to initiate sequential assignments. Amino-acid-selectively labeled NS4B can be readily obtained using cell-free synthesis, opening the door to combinatorial labeling approaches which should enable structural studies.     

Zu einem Phänomen der Lochkorrosionsbegrenzung bei hochlegierten Sonderedelstählen und NiCrMo-Legierungen in Chloridlösungen

On a phenomenon of the limitation of pitting corrosion at high alloyed special stainless steels and NiCrMo-alloys in chloride solutions Testing the pitting corrosion resistance of high alloyed special stainless steels and NiCrMo-alloys in chloride solutions there was observed a limitation of the pitting corrosion range toward more positive potentials. Above this limitation, the so-called pitting corrosion limitation potential, the pit initiation by all means is prevented, but the growth of pits which had been initiated before in the pitting corrosion range not necessarily comes to a stop. Therefore current density-potential curves which are obtained by downward polarization after an initial potential jump into the transpassive region and chronopotentiostatic tests are more suitable to investigate this phenomenon than cyclic polarization measurements and potentiostatic alteration tests. There is indicated a dependence of this phenomenon on temperature. The phenomenon of a limitation of the pitting corrosion range toward more positive potentials has been found until now at alloy 926, alloy 31, alloy 28, alloy 59 and alloy C-276.     

Strawberry juice colour: The effect of some processing variables on the stability of anthocyanins

The colour stability of juice and purées made from a mixture of two strawberry varieties, stored at + 20°C or at –20°C under aerobic and anaerobic conditions, was studied. High-performance liquid chromatography and spectrophotometric analysis were used to monitor the changes in colour during storage. Pelargonidin 3-glucoside comprised 80% of the total anthocyanin content. Four other pelargonidin-based peaks were found, being 10.4%, 3.5%, 0.7% and 0.3% of the total and two cyanidin peaks were present, being 3.3% and 0.4% of the total. Clarification before storage caused considerable losses in the initial anthocyanin concentrations. Storage conditions (air versus nitrogen) did not influence the rate of loss of anthocyanins during storage or the formation of polymeric pigments. There were no losses in anthocyanins and no increase in the amount of colour measured at 510 nm due to polymers in samples stored at–20°C. Polymerisation occurred in the samples stored at + 20°C, especially in the clarified samples.     

X-ray Fluorescence Uptake Measurement of Functionalized Gold Nanoparticles in Tumor Cell Microsamples

Quantitative cellular in vitro nanoparticle uptake measurements are possible with a large number of different techniques, however, all have their respective restrictions. Here, we demonstrate the application of synchrotron-based X-ray fluorescence imaging (XFI) on prostate tumor cells, which have internalized differently functionalized gold nanoparticles. Total nanoparticle uptake on the order of a few hundred picograms could be conveniently observed with microsamples consisting of only a few hundreds of cells. A comparison with mass spectroscopy quantification is provided, experimental results are both supported and sensitivity limits of this XFI approach extrapolated by Monte-Carlo simulations, yielding a minimum detectable nanoparticle mass of just 5 pg. This study demonstrates the high sensitivity level of XFI, allowing non-destructive uptake measurements with very small microsamples within just seconds of irradiation time.     

Suppression of the development of pores during laser-induced surface dispersion of TiC into aluminium, by means of a static magnetic field

A static magnetic field having the strength of B=0.6 T has been used as an additional process parameter in order to suppress the establishment of pores while dispersing TiC particles in surface layers of aluminium alloys using a laser. The migration of hydrogen towards regions of high temperatures within the melting pool can lead to the creation of gas bubbles, therefore yielding pores after resolidification in the processed layer. This mechanism (known for instance in welding technologies of aluminium) could be suppressed by Lorentz-forces induced by an externally applied magnetic field. It could be shown experimentally that magnetic fields could assist laser surface treatment processes beneficially if higher beam powers were coupled in. This may be interesting if, for instance, thicker dispersed layers should be achieved.     

Early age microstructure of Portland cement mortar investigated by ultrasonic shear waves and numerical simulation

This paper investigates the ability of a shear wave reflection (WR) method to monitor microstructural changes of Portland cement mortar during hydration. The wave reflection method measures the reflection loss of shear waves at an interface between a steel plate and mortar. Mortars with water/cement ratios of 0.35, 0.5 and 0.6 were tested at isothermal curing conditions of 25 °C. The numerical model HYMOSTRUC3D was used to simulate the evolution of microstructural properties of the cement paste phase of the tested mortars. The parameters obtained from the simulations were the volume fraction of the total and connected solid phase and the specific contact area of the hydrated cement particles. The investigations have shown that the wave reflection measurements are governed primarily by the degree of the inter-particle bonding of the cement particles as calculated from the specific contact area of a simulated microstructure.