Oxygen content of the fixative is important in the interpretation of the ultrastructure of ischaemic myocardium

Isolated rat hearts were subjected to 15, 45, or 60 minutes of global ischaemia and then fixed by perfusion at 37°C with glutaraldehyde containing various amounts of oxygen. This either had been bubbled with 100% oxygen (PO₂ 620 mm Hg) or with 100% nitrogen (PO₂ 40 mm Hg) immediately before use, or it had been routinely prepared and stored exposed to atmospheric oxygen (PO₂ 245 mm Hg). The ultrastructure of myocytes and endothelial cells subjected to 15 minutes of ischaemia was not affected by the treatment of the fixative. However, when the tissue subjected to longer periods of ischaemia was fixed with routinely prepared or oxygen-bubbled glutaraldehyde, ultrastructural changes characteristic of reoxygenation damage were uniformly evident in both the microvasculature and myocytes. These qualitatively distinct changes included mitochondrial swelling, cell swelling, endothelial bleb formation, and narrowing of capillary lumina. These abnormalities were not observed in tissue fixed with nitrogen-bubbled glutaraldehyde. These findings indicate that deliberate steps should be taken to reduce or eliminate dissolved oxygen from the fixatives used to study ischaemic tissues. Otherwise artefactual reoxygenation damage in vitro may occur and make valid ultrastructural interpretation difficult or impossible.     

Performance characteristics of a therapeutic ultrasound wire waveguide apparatus

Therapeutic ultrasound angioplasty has been investigated, clinically, by a number of researchers and represents a potentially promising therapy for the treatment of atherosclerotic lesions. To date, there has been no detailed analysis of the effect of mechanical design parameters, such as wire geometry or damping characteristics, on wire waveguide performance. An apparatus capable of delivering therapeutic ultrasound down small diameter nickel–titanium (NiTi) wire waveguides is described. The output peak-to-peak (p–p) displacements at the distal tip of a 1.0 mm diameter waveguide were measured experimentally, by means of an optical microscope and image analysis software. The output was measured for a range of waveguide lengths from 118 to 303 mm. Wire waveguide distal tip displacements as high as 98 μm (p–p) at 23.5 kHz were measured. For the range of lengths tested, the experimental measurements show the critical relationship between the length of the waveguide and the output distal tip displacements. A finite element model that can predict the resonant frequencies and distal tip displacements of various wire waveguide geometries and configurations, including the effect of damping, is presented. This numerical model has been validated against the experimental displacement data obtained. This will be a valuable design tool for ensuring the safety and effectiveness of therapeutic ultrasound angioplasty procedures.     

Propane conversion over zeolite catalysts: Comments on the role of Ga

The activation of propane using zeolite H-Y and Ga³⁺ exchanged zeolite Y indicates that in the presence of Ga³⁺ the mechanism of propane activation is changed from a cracking pathway to a dehydrogenation pathway. The presence of both Ga³⁺ and H⁺ are required to achieve this effect.     

Numerical and experimental study of a nonisothermal turbulent jet with a heavy impurity

Temperature and momentum distributions of the carrier phase are determined experimentally and compared to results of numerical calculations using the (k–) model.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 50, No. 5, pp. 735–743, May, 1986.     

Distribution of disperse impurity in turbulent jet

The concentration fields of disperse impurity are calculated on the basis of a k- model of turbulence in a wide range of Stokes numbers.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 49, No. 4, pp. 548–555, October, 1985.     

Copper Assisted Inverted Pyramids Texturization of Monocrystalline Silicon in a Nitrogen Bubbling Bath for Highly Efficient Light Trapping

Silicon - Inverted pyramid (IP) texturization on silicon wafers has recently attracted attention for the structure’s light trapping ability and low specific surface area. The later property...     

SULFUR RECOVERY WITH REDUCED EMISSIONS, LOW CAPITAL INVESTMENT AND HYDROGEN CO-PRODUCTION

The main disadvantage of the Claus process is that by introducing air as oxidant a large volume of tail gas is produced. This must be treated to reduce atmospheric emissions of sulfur-containing gases. The costs of the tail-gas unit are a significant fraction of the total capital and operating costs for sulfur recovery. A new process uses thermal decomposition of hydrogen sulfide in the presence of carbon dioxide instead of air oxidation. The products of this reaction are hydrogen, carbon monoxide, elemental sulfur, water vapor and carbonyl sulfide. Carbonyl sulfide is easily converted to H₂S and C0₂ by liquid- or vapor-phase hydrolysis. Unreacted H₂S and C0₂ are recovered by absorption and recycled to the reactor. Since no air is introduced, there is no tail gas and the tail-gas unit is eliminated, giving a substantial reduction in capital investment. The concentrations of sulfur-containing gases in the product streams depend only on the operation of the absorber and stripper units and can be controlled to very low levels by increasing stripper boil-up. Process operating costs depend on the level of sulfur recovery required and can also be much lower than those of the modified Claus Process.

The process chemistry depends on a shift in the equilibrium of H₂S decomposition caused by reaction of hydrogen with C0₂ by the reverse of the water-gas-shift reaction. Catalysts for this chemistry have been identified. Reactor conversion is further improved by rapid cooling of the reactor effluent gas. Other aspects of process design and operation confer further advantages with respect to the Claus process; however, the process equipment used is similar to that used in a Claus plant. Retrofit of existing plant to the new technology can therefore be considered.