大气状态下AFM阳极氧化加工Si的研究

Si纳米氧化线是构筑基于Si的纳米器件的基础。通过AFM针尖诱导阳极氧化加工的n型Si(100)的实验得到凸出的n型Si(100)氧化物高度和偏置电压成线性关系,与针尖扫描速度成负对数关系,并在前人的基础上深化了AFM针尖诱导氧化加工的机理和理论模型,得到了合适的加工条件为偏压8 V和扫描速度1μm/s。     

全球宽带接入市场发展分析分析

通过对目前宽带线路数最多的10个国家和地区、2003年上半年新增线路最多的10个国家、全球宽带业务普及率最高的10个国家和地区、部分运营商住宅DSL业务的第一年费用以及2000～2002年全球入门级住宅DSL业务价格的发展趋势等图表的分析,阐明了全球宽带接入市场的发展状况,指出了其市场规模继续扩大、经济发达国家宽带线路增长速度较快、普及率的差距逐渐缩小以及业务价格趋于稳定等特点.     

平行线束法的仿射研究

用 3 个仿射图的投射方向构成 1 个仿射坐标系,同时也构成 1 个三棱锥,在此仿射坐标系中用球面三角重新研究由两个仿射图求第 3 个仿射图的投影作图理论 ——平行线束法。进一步还给出了由两个仿射图得到正投影的条件、由两个正投影得到第 3 个正投影的条件、以及由 V,H 两投影得到指定方向上的正投影的条件,简化了研究过程,得到了更简单的公式。     

Failure analysis of aluminum cable steel reinforced (ACSR) conductor of the transmission line crossing the Paraná River

The failure of the conductor of the 460 kV overhead transmission line located along the crossing of the Paraná River was investigated. As a result of this failure, a blackout took place in the southern states of Brazil in January of 2002, reaching approximately 67 million inhabitants. Investigation of the external aluminium layer of the ACSR conductor near the fracture showed typical static deformation marks and dynamic fretting wear tangential marks, both associated with the presence of Al₂O₃ debris. Additionally, encrusted silicon particles were observed on the external surface of the strands. The internal Al layer showed elliptical deformation marks also associated with Al₂O₃ debris. Both Al₂O₃ and Si particles are efficient abrasive material, which associated with slight relative motion of metallic surfaces (clamp/strand and strand/strand) can promote fretting wear. Two types of fracture surface of the Al strands were identified: 45° and quasi-normal surfaces, the former being the predominant type. Delamination and particle detachment were the mechanisms of superficial degradation observed on the Al strands, indicating that the rupture of the strands occurred under a gross slip fretting regime induced by sub-conductor oscillation. Inspection of the internal surface of as-cast Al–10%Si spacer clamps revealed different stages of intense circumferential wear caused by the preferential cracking and particle detachment of the eutectic constituent of the as-cast microstructure. This intense wear reduces the clamping contact pressure, which allows higher displacement amplitude and leads to the critical fretting regime. Finally, a few suggestions are discussed to minimise the occurrence of future failures.     

线加权余量法及其在正交异性板弯曲分析中的应用

利用有限差分法对控制方程和边界条件进行半离散化,使其定义在一些离散线上,然后采用加权余量法求解。这就是本文提出的线加权余量法,也可称之为有限差分-加权余量分维耦合法。文中以正交各向异性薄板弯曲平衡问题为例推导了有关具体算式,给出了数值算例,说明了本文方法的有效性。     

同杆并架双回线基于电流突变量的综合选相

相电流差突变量选相元件在单回线故障中具有良好的选相性能，但在同杆双回线跨线故障中可能误选相。利用六序故障分量的分析方法，分析了相电流突变量在同杆双回线跨线故障中的幅值和相位特征，给出了其相位比相方程。在此基础上，提出了一种运用测量阻抗和方向元件相结合的综合选相方法，并给出了选相流程图。仿真结果表明，在双回线简单故障和跨线故障时，基于单回线单端电气量的同杆并架双回线综合选相方法具有较理想的选相性能。     

岩滩水电站由220KV升压为500KV运行

岩滩水电站升压一次成功，本文简要叙述岩滩水电站升压的各项工作和主要设备的安装试验情况。     

Construction of transmission lines above valuable standing timber

Problems with the construction of transmission lines above a forest are examined. Construction of lines above standing timber makes it possible to shorten the length of the route, eliminate the clearing of a continuous swath along the line, and reduce the volume of in-service work. To implement this solution, it is necessary to introduce changes and supplements to existing regulatory technical documents. __________ Translated from élektricheskie Stantsii, No. 10, October 2007, pp. 48–51.     

750kV输变电设备的国产化能力

文章介绍了750KV输变电设备国产化的进展情况，对750KV变压器，电抗器，互感器，开关设备、避雷器，高压套管和绝缘子等主要设备或部件在国内生产的基础条件，研制生产能力和生产周期进行了介绍。     

一起500kV线路计量点事故隐患的分析与思考

本文简要介绍了500kV某回线计量点验收时发现事故隐患的过程,从电容式电压互感器本身结构出发,详细分析了产生事故隐患的原因、带来的危害等,并由此提出了计量点验收工作的重要性和必要性。