Synthesis,characterization and magnetic properties of polythiophene/SrFe12-x(ZrZn)0.5xO19 nanocomposite as a microwave absorber

Ferrites are an important group of magnetic materials which are used as absorbers. The incorporation of ferrite and conducting polymer achieves great enhancement in microwave absorption properties. The nanocomposites of hexagonal ferrites embedded by conducting polymers such as polypyrrole, polyaniline and polythiophene (PTH) have been paid much attention. In the present study, strontium hexagonal ferrite doped by Zr and Zn with the final formula of SrFe_12-x(ZrZn)_0.5xO19 considering x = 0.9 and embedded by PTH was produced to achieve a nanocomposite with the highest microwave absorbing ability. In this study, after synthesis of SrFe₁₂O₁₉(ZrZn)_0.5xO19 and PTH, the nanocomposite was prepared by in situ polymerization. Wrapping the ferrite particles and PTH chains could form nanocomposite properly, and therefore acceptable interactions were observable between SrFe_12-x(ZrZn)_0.5xO19ferrite particles and PTH polymer chains in the composites. Assessing the X-ray diffraction (XRD) patterns of SrFe_12-x(ZrZn)_0.5xO19, PTH, and PTH/SrFe_12-x(ZrZn)_0.5xO19 nanocomposite indicated that the PTH characteristic peak shifts slightly and its peak intensity reduces, which may be attribute to the coating of PTH polymer chains onto SrFe_12-x(ZrZn)_0.5xO19 particles. We revealed also lower magnetic properties in the obtained nanocomposite. The morphological assessment also suggested that PTH could effectively coat the SrFe_12-x(ZrZn)_0.5xO19 particles. The synergistic effect of SrFe_12-x(ZrZn)_0.5xO19 particle plus PTH leads to microwave absorption percentage higher than 95% by PTH/SrFe_12-x(ZrZn)_0.5xO19 nanocomposite. Overall, nanocomposite creating by coupling interaction between SrFe_12-x(ZrZn)_0.5xO19 particles (x = 0.9) and PTH can effectively lead to achieve the highest rate of absorption of electromagnetic waves.     

Feedforward control of the transverse strip profile in hot-dip galvanizing lines

Hot-dip galvanizing is a standard technology to produce coated steel strips. The primary objective of the galvanizing process is to establish a homogeneous zinc layer with a defined thickness. One condition to achieve this objective is a uniform transverse distance between the strip and the gas wiping dies, which blow off excessive liquid zinc. Therefore, a flat strip profile at the gas wiping dies is required. However, strips processed in such plants often exhibit residual curvatures which entail unknown flatness defects of the strip. Such flatness defects cause non-uniform air gaps and hence an inhomogeneous zinc coating thickness. Modern hot-dip galvanizing lines often use electromagnets to control the transverse strip profile near the gas wiping dies. Typically, the control algorithms ensure a flat strip profile at the electromagnets because the sensors for the transverse strip displacement are also located at this position and it is unfeasible to mount displacement sensors directly at the gas wiping dies. This brings along that in general a flatness defect remains at the gas wiping dies, which in turn entails a suboptimal coating.In this paper, a model-based method for a feedforward control of the strip profile at the position of the gas wiping dies is developed. This method is based on a plate model of the axially moving strip that takes into account the flatness defects in the strip. First, an estimator of the flatness defects is developed and validated for various test strips and settings of the plant. Using the validated mathematical model, a simulation study is performed to compare the state-of-the-art control approach (flat strip profile at the electromagnets) with the optimization-based feedforward controller (flat strip profile at the gas wiping dies) proposed in this paper. Moreover, the influence of the distance between the gas wiping dies and the electromagnets is investigated in detail.     

Hierarchical electromagnetic absorption in micro-waveguide stuffed with magnetic media for resin-based composites of graphene nanosheets and manganese oxides

Waveguide configurations of hierarchical system are proposed as new microstructures for composites in absorbing enhancement. Supercritical fluid (SCF) one-pot exfoliation of layered graphite and manganese oxide mixing materials is developed to obtain a hierarchical system, containing graphene nanosheets (GNS) and exfoliated manganese oxides (EMO) in different sizes. Composites with GNS–EMO embedded in epoxy resin matrix are produced for a design of dielectric and magnetic loss integrated absorber. Volume fraction of GNS–EMO in composites is given for an optimal quantity of resin epoxy in fixation and formation. The effect of mixing ratios between electric and magnetic components is provided for the design of dielectric and magnetic loss integrated absorbers. Frequency shifting phenomena are revealed in the component adjusting course. Excluding the offsetting sizes, reflection loss of composites is enhanced as thickness increases. Synergistic effect of electric and magnetic coordinated materials demonstrates the superiority of micro-waveguide structures in GNS–EMO composite absorber.     

搅拌式风力致热装置启动性能研究

搭建搅拌式风力致热试验台,以自制的2种致热器为研究对象,使其分别在3个不同平均角加速度24.92、14.66、8.04 rad/s2下启动。通过动态扭矩测试仪和数据采集仪测试记录致热器启动阶段的相关数据。结果表明:致热器启动时所需扭矩与角加速度的一次方、转速、叶片半径的二次方成正比,同时得出这些因素之间的关系式;满负荷时,启动扭矩会出现一个峰值,且角加速度越大峰值越大,自然风必须提供峰值以上的扭矩,否则装置无法启动。     

Polyaniline-based networks combined with Fe3O4 hollow spheres and carbon balls for excellent electromagnetic wave absorption

Polyaniline (PANI)-based networks combined with Fe₃O₄ hollow spheres and carbon balls (FCP) for improved electromagnetic wave (EMW) absorption were investigated using an easy-to-industrialize solvothermal and physical method. Hollow structure Fe₃O₄ spheres with a lower density than that of the common solid sphere were prepared. As a thin and light magnetic material, Fe₃O₄ hollow spheres generate magnetic loss, carbon balls and PANI networks generate dielectric loss. The magnetic and conductive parts play appropriate roles in achieving complementarity in the EMW absorption. The relatively high specific surface area introduced by PANI networks promotes interfacial polarization and further supports dielectric loss. In conclusion, the above reasons provide multiple attenuation mechanisms. Samples FCP1 (?65.109 dB, at 12.800 GHz, 1.966 mm, from 5.6 to 18.0 GHz) and FCP2 (?61.033 dB, at 8.480 GHz, 3.328 mm, from 4.3 to 18.0 GHz) demonstrated a wide bandwidth, a small thickness, a minimum reflection loss (R_L), and a low loading ratio (25%) in paraffin-based composites. Specifically, their loading ration of 25% is much lower than the loading ratio of conventional materials (usually 50% and above). In addition, the bandwidth is excessively wide, above 12 GHz, possessing good absorption performance in continuous intervals with different thicknesses. Such excellent characteristics have rarely been reported in literature.     

Effect of Sr doped the YFeO3 rare earth ortho-ferrite on structure,magnetic properties,and microwave absorption performance

Given the remarkable performances of rare earth multiferroic ortho-ferrites with magnetic optical and dielectric properties, the Y_1-xSr_xFeO₃ (x = 0, 0.05, 0.1, 0.15) perovskite structure microwave absorbing ferrite materials was successfully synthesized by Sr²⁺ ions A-site doping based on sol-gel technology in this paper. The XRD of all samples was refined with FullProf software, which confirmed the formation of the orthogonal perovskite structure (SG: Pnma). The SEM and TEM results display the average particles size of the samples is distributed between 110 and 160 nm. The increase of Sr doping concentration leads to the increase of particles size, which may be related to the growth of preferred orientation and incomplete substitution. The XPS analysis shows that Fe³⁺ was accompanied by the presence of Fe²⁺ with the doping of Sr²⁺ ions and oxygen vacancies increased significantly. The samples change from weak ferromagnetic state to paramagnetic state with the increase of Sr content. The minimum reflection loss (RL) of the Y_0.95Sr_0.05FeO₃ samples at 12.2 GHz reached −30.87 dB with thickness of 2.2 mm, where its effective absorption bandwidth (EAB, RL ≤ −10 dB) reached 2.4 GHz (11.3–13.7 GHz). Moreover, the EAB of the Y_0.85Sr_0.15FeO₃ samples reached 2.64 GHz, and the corresponding range is 9.0–11.6 GHz (X-band).     

三相交流电动机启动过程参数数值模拟

提出一种进行模拟计算电动机启动过程中各参数的新方法。利用电机运行理论,结合物体定轴转动定律,推导出电机运行参数随时间变化的函数关系式。将计算公式离散化后,对电机启动过程运行规律进行求解。实例计算了一种型号潜油三相电动机启动时电动机定子电流、转子电流、激磁电流、扭转力矩、转速参数及效率参数等随时间或转差率的变化规律,其变化曲线与试验结果基本一致,说明提出的计算方法是有效、正确、适用的。     

DC/DC电源中的电磁干扰及其对策

概述了电磁干扰(EMI)和电磁兼容(EMC)的基本知识，对DC／DC电源中的电磁干扰进行了综合分析，并给出了各自的解决方案。     

Profiling Voids Embedded in a Slab by a Non-Linear Model

In this paper, by applying a non linear model for the electromagnetic inverse scattering, a technique for the dielectric profiling of a planarly layered medium is investigated and applied to void localization and diagnostics inside a homogeneous lossless slab (one-dimensional geometry). Data are collected under plane wave multifrequency normal incidence. Suitable finite dimensional representations for the unknown functions are introduced and their influence on the model is discussed. The resulting functional equation is solved by the method of weighted residuals and the solution algorithm amounts to minimizing a non quadratic function, where particular attention is devoted to reduce the occurrence of local minima. Finally, the inversion algorithm is validated by applications to both simulated and experimental data.     

屏蔽人体模型对电磁波吸收的数值模拟研究

本文用时域有限差分法计算了三类电磁特性不同的材料屏蔽下三层无限长椭圆柱人体模型对电磁波的吸收。结果表明 ,功率密度相同 ,频率在 0 .2～ 6GHz之间的平面电磁波照射下 ,模型吸收的能量、能量在体内的分布及两者对入射电磁波频率的敏感程度严重地受到外加屏蔽的影响。考察了屏蔽材料的电磁特性与其屏蔽效能之间的关系。三类材料的比较显示 ,对人体电磁辐射防护 ,耗散材料优于非耗散材料 ,导电材料优于非导电材料。