排序方式: 共有100条查询结果,搜索用时 15 毫秒
1.
《Materials Science & Technology》2013,29(8):1046-1050
AbstractCf/SiC was successfully joined to Ti alloy with Ag–Cu–Ti–W, Ag–Cu–Ti–SiC and Ag–Cu–Ti–TiC mixed powders by some suitable brazing parameters. Microstructure and shear strengths of the preformed joint were investigated. The results showed that the W particulate and reaction products can uniformly distribute in the brazing layer of the performed joint. These composite brazing layers relaxed the thermal stress of the joint effectively. These characteristics were beneficial to the joint, which had shear strengths that were significantly higher than the optimal shear strengths of the joint brazed with pure Ag–Cu–Ti at room temperature and 500°C. 相似文献
2.
AbstractCompressive properties are investigated for the porous Ni materials processing by innovated powder metallurgical (PM) method. The porous Ni materials first show a short elastic region, then a long and oblique stress yield region within the strain range of about 10–50%, and finally, a densification region where the stress increases rapidly. 相似文献
3.
《Materials Science & Technology》2013,29(1):57-67
AbstractIn the present study, three aluminium based functionally gradient materials (FGMs), reinforced with different ceramic particulates (silicon carbide, aluminium oxide, and titanium carbide), were successfully synthesised using the innovative gradient slurry disintegration and deposition (GSDD) technique. The results for Al/SiC and Al/Al2O3 revealed, in common, an increase in the weight percentage of reinforcement along the direction of deposition, to result in an increase in porosity and microhardness. However, for Al/TiC, the reverse trend was observed, with porosity and microhardness decreasing with increasing distance from the base of the ingot. The porosity levels for Al/TiC were also found to be significantly lower than those ofthe other two FGMs. Thermomechanical analysis of the FGMs showed thatthe average coefficient of thermal expansion of the high reinforcement end was reduced, as compared to the high aluminium end. Sliding wear test results also revealed that the high reinforcement end was more wear resistant than the high aluminium end, except for the case of Al/Al2O3. An attempt is made to interrelate the effects of different types of particulates, with microstructural development, microhardness and wear rate results obtained in the present study. 相似文献
4.
《Science & Technology of Welding & Joining》2013,18(7):616-625
AbstractResistance spot welding experiments were conducted on dissimilar material combination of HSLA350/DP600 steels. The welds were characterised using optical and scanning electron microscopy. The fusion zone of the dissimilar material spot weld was predominantly martensitic with some bainite. Mechanical properties were also determined by tensile shear, cross tension and fatigue tests. The performance of dissimilar material spot weld was different from that of the similar ones in each of the HSLA350 and DP600 steels and exhibited different heat affected zone hardness. The DP600 weld properties played a dominating role in the microstructure and tensile properties of the dissimilar material spot welds. However, the fatigue performance of the dissimilar welds was similar to that of the HSLA350 welds. Fatigue tests on the dissimilar material spot welds showed that the 5·5 mm diameter nugget exhibited higher fatigue strength than the 7·5 mm diameter nugget. 相似文献
5.
《Journal of Adhesion Science and Technology》2013,27(12):1339-1365
We have investigated the adhesion properties of microcrystalline diamond thin films on Ti-Al-V alloy, Co-Cr-Mo alloy and steel. Microcrystalline diamond possesses high hardness, a low coefficient of friction, extreme chemical inertness and biocompatibility; these properties can enhance the performance of metal alloys used in medical implants and in machine tools. We have adopted three methods for improving the adhesion of microcrystalline diamond to commonly used metal alloys: (1) by alloying the substrate surface to minimize graphitization; (2) by employing appropriate buffer layers between the diamond film and the substrate; and (3) by creating functionally gradient diamond-(titanium carbide, tungsten carbide, titanium nitride and aluminum nitride) composites. We have demonstrated that functionally gradient discontinuous buffer layers of titanium carbide, titanium nitride, aluminum nitride and tungsten carbide are able to control stress and graphitization in microcrystalline diamond thin films. This work on buffer layers and functionally gradient coatings should allow the development of more adherent crystalline diamond films for medical and tribological applications. 相似文献
6.
The primary parameters of electrophotographic papers are surface charge, and the decay of this charge under both dark and illuminated ambient conditions. The inter-relationship of these parometers is of great practical signiftcance in machine design. It is suggested that the results from conventional static methods for their measurement can be misleading. Special equipment has been constructed for the examination of electrophotographic materials under dynamic conditions. Experimental results are presented together with an indication of their value in assessing the practical performance of electrophotographic papers and their influence in machine design. 相似文献
7.
《Materials Science & Technology》2013,29(4):472-476
AbstractIn this paper, experimental and numerical methods have been applied to the study of composite dynamics. Dynamic orthotropic photoelasticity is employed in the experimental work and the time domain boundary element method for anisotropic media is adopted for the numerical analysis. A fibre reinforced birefringent composite plate is used to model the semi-infinite orthotropic domain with a circular hole. A rifle bullet was used to exert the impact loading with the loading direction parallel and perpendicular to the fibre direction. In the experiments, the propagation, reflection, and diffraction of the stress wave around the hole were recorded and the results were analysed. The time histories of the stress components were obtained from the same experiments and compared with the results from the corresponding computations carried out using the time domain boundary element method. Some valuable data regarding composite dynamics and associated engineering implications were obtained. The comparative study also demonstrates the applicability and accuracy of the two methods for wave propagation problems in orthotropic media. 相似文献
8.
《International Journal of Cast Metals Research》2013,26(1-4):156-161
AbstractThe addition of Re, Fe and Cr into Ti–50 mol.-%Ni has been carried out to improve the oxidation and mechanical properties. The mono phase consisting of TiNi with the B2 type structure was identified in micro-alloyed materials proposed on the basis of the d-electrons concept. Experimentally, TiNi alloys were melted and solidified by the cold crucible levitation melting (CCLM) method. The TiNi–(Cr, Fe, Re) alloys with high purity and without contamination from a crucible were prepared, and the homogeneous microstructure was achieved by the diffusion mixing effect of CCLM even in the as-cast alloys which contained Re and Cr with higher melting temperatures and different specific gravities. The transformation from austenite to martensite phases occurred in all alloys below or above room temperature. Some alloys had the ability of shape memory even at room temperature. Ternary alloys showed a higher flow stress level compared with the binary TiNi alloy. On the other hand, the oxidation at 1273 K was promoted by the formation of titanium oxides (TiO2) on the alloy surfaces. The oxidation resistance was improved by the formation of the continuous Cr2O3 film in TiNi–Cr alloys. The alloying effects by ternary elements (Re, Fe, Cr) in the intermetallic TiNi as well as metallic materials were explained well using two parameters used in the d-electrons concept. 相似文献
9.
《Journal of Adhesion Science and Technology》2013,27(9):1225-1234
The practical application of the glycolysis mixture of polyurethane wastes is reported. It was found that in the presence of 4,4′-diphenylmethane diisocyanate (MDI) both the separated upper phase of the glycolysis mixture and the complete two-phase reaction mixture could be used as components of the urethane adhesive mixtures for bonding woods, metals, plastics, glass, ceramics, paper and leather. The adhesive properties were determined by tensile-cutting, cutting- and bending strengths, as well as peel resistance measurements. The method to use the complete glycolysis mixture is also reported. The reaction mechanism of bonding is also discussed. 相似文献
10.