Synthesis and characterization of zeolite NaY from rice husk silica

Rice husk silica (RHS) in amorphous phase with 98% purity was prepared from a waste rice husk from rice milling by leaching with hydrochloric acid and calcination. The RHS was used effectively as a silica source for the synthesis of zeolite Y in sodium form (NaY). The zeolite in pure phase was obtained from a two-step synthetic route in which the starting gels were mixed, aged for 24 h at room temperature and crystallized for 24 h at 90 °C. The diameter of single crystal particles from a scanning electron microscope was approximately 1.0 μm, whereas the average particle diameter from laser diffraction particle size analyzer was approximately 10 μm because of the agglomeration of small crystals. Longer crystallization time in this route resulted in a mixed phase containing NaY and zeolite P in sodium form (NaP). In addition, a one-step synthetic route (no aging) was studied and the product was also a mixed phase zeolite.     

ZL101合金锶变质效果及热处理工艺的改进

对现场生产的ZLl01合金铸件材质进行了全面分析，针对存在的产品成分不准，变质效果不好，力学性能不合格的问题，通过改进合金的锶变质工艺和热处理工艺，改善了合金的组织和性能，达到了对材料的成分、性能的各项要求。     

Improvement in Stress Corrosion Crack Growth Resistance of an Austempered Cast Steel by a Novel Two-Step Austempering Process

An investigation was carried out to examine the influence of microstructure on the stress corrosion cracking (SCC) growth behavior of an austempered high-carbon (1.00%), high-silicon (3.00%), and high-manganese (2.00%) cast steel. Compact tension specimens were prepared from this cast steel as per American Society for Testing Materials standard E-399 and were given four different heat treatments to produce different microstructures. The SCC behavior of these specimens was studied in 3.5% NaCl solution. The test results indicate the K_ISCCvalue of the material increases as the austenite content increases. Significant improvement in SCC resistance was achieved by using a novel two-step austempering process. Intergranular crack growth was observed in all these specimens.     

钙铁硅铁磁体微晶玻璃热处理制度的研究

使用XRD、DTA、VSM等分析测试手段对在还原气氛下含少量B2O3、P2O5钙铁硅微晶玻璃的热处理制度进行了较深入的研究。研究发展，预核化处理对于钙铁硅微晶玻璃的晶化无明显作用。900℃作为钙铁硅微晶玻璃的晶化温度较适宜，晶化时间宜8h以上。     

Optimizing the Vacuum Heat-Treatment of Hot-Work Tool Steels by Linear Elastic Fracture Mechanics

Linear elastic fracture mechanics was used to optimize the vacuum heat-treatment procedures for conventional hot-work AISI H11 tool steel. The fracture toughness was determined with non-standard, circumferentially notched and fatigue-precracked tensile-test specimens. The fracture-testing method is sensitive to changes caused by variations in the microstructure resulting from the austenitizing and tempering temperatures as well as the homogeneity of the material itself. The combined tempering diagram- Rockwell-C hardness, Fracture toughness K_Ic, Tempering temperature was used for the choice of the vacuum heat-treatment parameters necessary to obtain the best properties for a given application with respect to the investigated steel.     

Effect of deposition conditions on the properties and annealing behavior of cold-sprayed copper

The deposition of copper by cold gas dynamic spraying has attracted much interest in recent years due to the capability to deposit low-porosity oxide-free coatings. However, it is generally found that as-deposited copper has a signicantly greater hardness, and potentially lower ductility, than bulk material. In this article, copper was deposited by cold spraying using helium as the driving gas at both 298 and 523 K. Evidence is presented indicating that the material sprayed at the lower temperature exhibits a lower dislocation density throughout the grain structure than the material sprayed at the higher temperature. The low stacking fault energy of copper restricts recovery during annealing, and thus microstructural changes during annealing only proceed once recrystallization begins. The material sprayed at low temperature (with the low dislocation density) exhibited recrystallization at annealing temperatures as low as 373 K with a corresponding reduction in hardness. However, the copper sprayed with helium at 523 K was resistant to annealing at temperatures up to 473 K where the dislocations in the structure prevented recrystallization. However, at higher temperatures, recrystallization did proceed (with corresponding reductions in hardness). The fracture behavior of the copper that was cold sprayed with helium at 523 K, both in the as-sprayed condition and following annealing, was measured and explained in terms of the annealing mechanisms proposed. The original version of this paper was published in the CD ROM Thermal Spray Connects: Explore Its Surfacing Potential, International Thermal Spray Conference, sponsored by DVS, ASM International, and HW International Institute of Welding, Basel, Switzerland, May 2–4, 2005, DVS-Verlag GmbH, Düsseldorf, Germany.     

Influence of the aluminum surface on the final results of a two-step anodizing

1050 Aluminum alloy sheets were used to analyze the influence of a surface treatment on the characteristics of the alumina layer formed in a two-step anodizing. The study was mainly focused on two pretreatment steps, electropolishing and acid etching, as well as on the intermediate stripping step. The pretreatment procedure was optimized by accounting for the chemical nature of the substrate, with the results indicating that additional pretreatment steps enhanced the self-ordered porous arrangement. The E-t curves recorded during the experiments demonstrated that the best alumina layers were obtained when the first barrier layer had a high resistance; i.e., a high anodizing potential. The application time of the stripping step was optimized to clean the surface from alumina remains, without damaging the aluminum substrate. By optimizing all of these experimental conditions, we were able to obtain porous anodic aluminum oxide layers displaying ordered domains several hundreds of nanometers in length.     

5CrMnMo钢中、小型热锻模具的强韧化热处理

5CrMnMo钢中、小型热锻模具经强韧化工艺处理后与经常规工艺热处理相比，强韧性、疲劳抗力和使用寿命显著提高，且工艺简单，操作方便，质量稳定。     

Studies on Preparation of Onion-like Fullerenes by Vacuum Heat-treatment

Onion-like Fullerenes were produced at high-temperature in vacuum. The morphology of the carbon nano onion-like fullerenes was examined and characterized by high-resolution transmission electron microscopy (HRTEM). It can be seen that the nano-sized, onion-like fullerenes possess high degree of graphization. The results suggested that the catalyst is the main factor affecting the size and yield of the fullerenes. The method is very promising for simple mass production.     

含Zr多晶Ni3Al合金在不同热处理温度下的组织与性能

研究了冷轧多晶Ni3Al-(0．2％，0．6％，1．0％，1．5％)Zr(原子分数)合金在不同热处理温度(800-1100℃)下的显微组织和力学性能，结果表明，适当的热处理温度，可使无硼Ni3Al-Zr多晶合金获得优良的室温拉伸强度和塑性，随着热处理温度的升高，不同Zr含量Ni3Al合金的再结晶体积分数增加，再结晶晶粒尺寸增大，室温拉伸强度下降．随着合金中Zr含量的增加，再结晶温度降低，再结晶晶粒尺寸减小．不同Zr含量Ni3Al合金的拉伸塑性明显依赖于热处理温度，对于低Zr(0．2％)合金，在1000℃热处理后，拉伸塑性最佳；对于中Zr(0．6％)合金，在850℃热处理后，拉伸塑性达到最大值；对于高Zr(≥1．0％)合金，拉伸塑性峰值出现在900℃热处理下，当热处理温度超过900℃，拉伸塑性显著降低。