采用八叉树和OSG分页结点的海量点云三维可视化

针对现有海量点云可视化方法存在索引构建时间长、内存占用大等问题，研究一种八叉树索引结合OSG分页结点的快速可视化方法，可在占用较小内存的基础上快速建立点云索引并实时调度。采用八叉树索引结构对海量点云进行数据组织，建立各层级的八叉树结点并以文件映射的方式分块保存，对结点文件重组织转换为支持OSG渲染引擎的多分辨率点云数据。采用基于OSG分页结点的实时调度技术，对海量点云进行高质量可视化。与目前两款主流的点云数据处理商业软件进行实验对比分析，结果表明所提方法具有索引建立速度快、内存占用小等优点，同时可视化交互更加流畅，适用于各种配置计算机下海量点云数据的调度管理与实时可视化。     

Artificial bee colony based algorithm for maximum power point tracking (MPPT) for PV systems operating under partial shaded conditions

Artificial bee colony (ABC) algorithm has several characteristics that make it more attractive than other bio-inspired methods. Particularly, it is simple, it uses fewer control parameters and its convergence is independent of the initial conditions. In this paper, a novel artificial bee colony based maximum power point tracking algorithm (MPPT) is proposed. The developed algorithm, does not allow only overcoming the common drawback of the conventional MPPT methods, but it gives a simple and a robust MPPT scheme. A co-simulation methodology, combining Matlab/Simulink™ and Cadence/Pspice™, is used to verify the effectiveness of the proposed method and compare its performance, under dynamic weather conditions, with that of the Particle Swarm Optimization (PSO) based MPPT algorithm. Moreover, a laboratory setup has been realized and used to experimentally validate the proposed ABC-based MPPT algorithm. Simulation and experimental results have shown the satisfactory performance of the proposed approach.     

“Size effect” in the fatigue behavior of Friction Stir Welded plates

Comparative fatigue tests were carried out on Friction Stir Welded specimens of a 2195-T8 aluminum–lithium alloy that differed significantly in width. The width of the larger specimens was over thirteen times greater than that of the small specimens. Fatigue results showed a clear “size effect”, i.e. fatigue life of large specimens was about 40% of the corresponding value of small specimens. The Equivalent Initial Flaw Size methodology was adopted to correlate the two sets of results. Fatigue crack initiation life was disregarded with respect to crack propagation life, and fatigue life was evaluated only as propagation of a small pre-existing defect. Following this methodology, test results of small specimens were used to evaluate the initial equivalent flaw contained in each specimen. It was assumed that this data followed a normal distribution. The equivalent initial flaw in larger specimens was evaluated by simple geometrical considerations. A very good assessment of mean fatigue life and scatter in the fatigue results of large specimens was obtained by simulating the propagation of these defects. Calculations were carried out by taking also welding residual stresses into account, but the results demonstrated that this effect was not significant.     

Fatigue performance of Friction Stir Welded titanium structural joints

The Friction Stir Welding process for producing corner and T-joints out of 6 mm Ti–6Al–4V was developed in this effort using previous work on butt weld joints as a starting point. A limited number of corner joints were also subjected to a bending fatigue test to preliminarily assess the applicability of the process in producing fatigue critical structures. These results were also compared to predictions made by applying stress concentration factors to previously generated uniaxial butt joint test data. While additional testing is still required to obtain a higher degree of confidence in the conclusions of this study, it was found that the performance of these corner joints in fatigue could be compared to butt joint data when a geometrically based stress concentration factor is applied. Furthermore, these welded joints possessed equivalent fatigue performance relative to identical test specimens machined from wrought product forms, both bar and extrusion. Thus, from the perspective of fatigue design, this study has shown that Friction Stir Welding is able to produce structures with the same performance as currently made from wrought materials.     

离心泵并联运行工况点的数值求解

建立了求解多台不同型号离心泵并联运行工况点的数学模型,给出了用数值计算中的“二分法”求解该模型的方法,并附有用Exce l计算的实例。     

红外光谱法用于快速测定车用柴油酸度等性质的研究

针对车用柴油酸度等性质测定过程繁琐，采用衰减全反射样品池测定车用柴油的红外光谱，用偏最小二乘法（PLS）建立红外光谱测定车用柴油酸度、密度、闪点和凝点的4个校正模型，验证标准误差分别为0.46 mg/(100 mL),0.77kg/m3,2.60 ℃,2.77 ℃，该方法符合标准方法再现性要求。与标准方法相比，该方法具有无需预处理、操作简单、测量快速、重复性好等优点。     

XMAC纵波时差高分辨率处理方法

在充分调研阵列声波测井分波提取方法的基础上，针对阿特拉斯公司的交叉多极子阵列声波测井（XMACⅡ）提供的单极波形信息，研究纵波时差提取及高分辨率处理方法。首先利用相关-互功谱法高精度地提取纵波时差，然后针对XMACⅡ仪器的接收阵列，研究组合子阵列的方法，形成共发射子阵列和共接收子阵列，最后利用子阵列对提取的纵波时差做高分辨率处理。处理现场实际测井资料，并将高分辨率处理成果与引进的eXpress软件处理成果、实测的国产高分辨率声波（纵波）测井曲线及岩心纵波时差对比分析，表明该方法提取的纵波时差曲线的纵向分辨率有很大提高，时差计算准确可靠，提取的单极纵波时差与国产高分辨率声波时差及岩心纵波时差的平均相对误差均小于7%。该方法具有较高的实用价值和广阔的应用前景。     

腐蚀阴极尖端的新方法

给出一种腐蚀阴极尖端的新方法,使得对阴极常用金属材料(W,Mo,Ir,Ta等)制作的阴极尖端的腐蚀效果明显,针尖对称性和重复性都很好,成品率和质量都有所提高.     

新安江流域安徽省地区水环境状况分析

统计分析流域内点源污染、面源污染产生量与污染物入河量的调查监测数据,结果表明:安徽省辖新安江流域点源入河系数约为面源入河系数2~3倍,点源污染是流域内主要污染来源,但面源污染的作用不容忽视,尤其是总磷,有近2/3来自面源,相对省辖淮河、长江两流域来说,面源污染贡献率明显增大。指出流域污染防治必须综合考虑点、面源污染两个方面;在点源污染不太严重的情况下,对面源污染的治理必须引起足够的重视,才能取得实效。     

邻—(4—乙基苯甲酰基)苯甲酸的研究

本文阐述了通过Friedel-Crafts反应合成邻-(4-乙基苯甲酰基)苯甲酸的方法.研究了影响产物质量的因素,提出了适宜的工艺条件.