Agronomic performance of high oleic,low linolenic soybean in Tennessee

Soybean oil hydrogenation alters the linolenic acid molecule to prevent the oil from becoming rancid, however, health reports have indicated trans-fat caused by hydrogenation, is not generally regarded as safe. Typical soybeans contain approximately 80 g kg⁻¹ to 120 g kg⁻¹ linolenic acid and 240 g kg⁻¹ of oleic acid. In an effort to accommodate the need for high-quality oil, the United Soybean Board introduced an industry standard for a high oleic acid greater than 750 g kg⁻¹ and linolenic acid less than 30 g kg⁻¹ oil. By combing mutations in the soybean plant at four loci, FAD2-1A and FAD2-1B, oleate desaturase genes and FAD3A and FAD3C, linoleate desaturase genes, and seed oil will not require hydrogenation to prevent oxidation and produce high-quality oil. In 2017 and 2018, a study comparing four near-isogenic lines across multiple Tennessee locations was performed to identify agronomic traits associated with mutations in FAD3A and FAD3C loci, while holding FAD2-1A and FAD2-1B constant in the mutant (high oleic) state. Soybean lines were assessed for yield and oil quality based on mutations at FAD2-1 and FAD3 loci. Variations of wild-type and mutant genotypes were compared at FAD3A and FAD3C loci. Analysis using a generalized linear mixed model in SAS 9.4, indicated no yield drag or other negative agronomic traits associated with the high oleic and low linolenic acid genotype. All four mutations of fad2-1A, fad2-1B, fad3A, and fad3C were determined as necessary to produce a soybean with the new industry standard (>750 g kg⁻¹ oleic and <30 g kg⁻¹ linolenic acid) in a maturity group-IV-Late cultivar for Tennessee growers.     

Effect of heat treatment on structural,morphological, dielectric and magnetic properties of Mg–Zn ferrite nanoparticles

Green combustion was used to prepare a ferrite composition of Mg_0.4Zn_0.6Fe₂O₄ using a blend of fresh lemon juice as a natural fuel-reductant. Effect of heat treatment on phase, morphological, dielectric, and humidity sensor properties is discussed. The formation of a cubic spinel ferrite has been established by XRD-diffraction and vibrational spectroscopic studies. The experimental lattice parameter ranges from 8.3721 to 8.3631 Å. The broadening of octahedral band (υ₂) in the vibrational spectra is an identification for the existence of ferrite nanoparticles in various sizes. The typical crystallite size ranges from 10.2 to 36.9 nm. Using micrographs obtained from field-effect scanning electron microscopy (FESEM), researchers observed a spherical-shaped microstructure with agglomerated nanoparticles. Dielectric investigations have shown that the current ferrite composition has typical dielectric dispersion. The highest reported value for saturation magnetization (M_s) in the present study is 33 emu/g. Magnetic behaviour is primarily influenced by magnetocrystalline anisotropy, cation distribution, and crystallite size. The existence of void spaces in the sintered samples, as well as their porous nature, rendered them suitable for humidity sensor applications. Sintered samples have good sensing capability at 900 °C. The current findings are integrated in terms of cation distribution and magnetocrystalline anisotropy, assuming fine size effects of ferrite nanoparticles.     

Automatic design for shop scheduling strategies based on hyper-heuristics: A systematic review

Against the background of smart manufacturing and Industry 4.0, how to achieve real-time scheduling has become a problem to be solved. In this regard, automatic design for shop scheduling based on hyper-heuristics has been widely studied, and a number of reviews and scheduling algorithms have been presented. Few studies, however, have specifically discussed the technical points involved in algorithm development. This study, therefore, constructs a general framework for automatic design for shop scheduling strategies based on hyper-heuristics, and various state-of-the-art technical points in the development process are summarized. First, we summarize the existing types of shop scheduling strategies and classify them using a new classification method. Second, we summarize an automatic design algorithm for shop scheduling. Then, we investigate surrogate-assisted methods that are popular in the current algorithm field. Finally, current problems and challenges are discussed, and potential directions for future research are proposed.     

Digital Microfluidics for Manipulation and Analysis of a Single Cell

The basic structural and functional unit of a living organism is a single cell. To understand the variability and to improve the biomedical requirement of a single cell, its analysis has become a key technique in biological and biomedical research. With a physical boundary of microchannels and microstructures, single cells are efficiently captured and analyzed, whereas electric forces sort and position single cells. Various microfluidic techniques have been exploited to manipulate single cells through hydrodynamic and electric forces. Digital microfluidics (DMF), the manipulation of individual droplets holding minute reagents and cells of interest by electric forces, has received more attention recently. Because of ease of fabrication, compactness and prospective automation, DMF has become a powerful approach for biological application. We review recent developments of various microfluidic chips for analysis of a single cell and for efficient genetic screening. In addition, perspectives to develop analysis of single cells based on DMF and emerging functionality with high throughput are discussed.     

Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.     

Study of metal assisted anisotropic chemical etching of silicon for high aspect ratio in crystalline silicon solar cells

Textured surface is commonly used to enhance the efficiency of silicon solar cells by reducing the overall reflectance and improving the light scattering. In this study, a comparison between isotropic and anisotropic etching methods was investigated. The deep funnel shaped structures with high aspect ratio are proposed for better light trapping with low reflectance in crystalline silicon solar cells. The anisotropic metal assisted chemical etching (MACE) was used to form the funnel shaped structures with various aspect ratios. The funnel shaped structures showed an average reflectance of 14.75% while it was 15.77% for the pillar shaped structures. The average reflectance was further reduced to 9.49% using deep funnel shaped structures with an aspect ratio of 1:1.18. The deep funnel shaped structures with high aspect ratios can be employed for high performance of crystalline silicon solar cells.     

A new design strategy for DC/DC LLC resonant converter: Concept,modeling, and fabrication

In this paper, a new design procedure for LLC converter has been introduced. In fact, this method is a computer-based design algorithm based on a numerical technique. In the process of designing, the value of the resonant element is obtained by solving the LLC converter fundamental equation. This converter will be controlled by using state feedback, such as output voltage variable. As a matter of fact, in a control system, the change of output voltage (because of load variation) will affect the switching frequency, so the output voltage will be tuned. In the designing process, the fundamental equations of LLC converter are obtained, and the value of the resonant elements is calculated. Also, a comparison analysis is carried out between the proposed and typical methods. The simulation is done to investigate the validity of the proposed method. Moreover, a prototype is manufactured, and the experimental test is done to evaluate its applicability.     

基于谐振原理的硅微机械加速度计

基于力学振动原理 ,导出敏感梁类谐振振动的微分方程 ,给出了振梁型加速度计的设计原理。指出了加速度计谐振梁频率的相对变化量与梁的厚度无关 ;为避免输出非线性频率信号 ,频率的相对变化率和激励振动的振幅都不宜太大     

建筑墙体表面传热系数辨识研究

对实验房间南向墙体内表面中心区域的换热过程进行实验，发现当风速在0－5．5m/s之间时，表面传热系数在8－18W（m^2.K）之间波动，而风向对墙体表面传热系数影响不大；用辅助变量法分析墙体表面传热过程，并结合实验推导出墙体表面传热系数。模型的预测结果与实测结果吻合良好。