沉管隧道水下最终接头施工技术初探

简述了沉管隧道水下最终接头施工技术的应用现状，结合具体隧道工程实例，从外模工程、混凝土结构两方面介绍了最终接头施工技术，表明了该技术具有运用价值。     

自由锻锤上冷冲厚板新工艺

介绍了自由锻锤上冷冲厚板工艺的特点和模具主要结构。以及如何解决凸凹模间隙、选用小间隙冲孔时刃口磨损加剧的问题。研制出了降低磨损。提高模具寿命的润滑剂配方。设计了适合自由锻锤上厚板冲孔的模具，对在自由锻锤上厚板冲孔进行了有益的尝试。扩大了自由锻设备的加工范围。解决了不具备大型压力机情形下的生产难题。     

Influences of metallic polymeric materials on the properties of fresh polyester and acrylic polymer concrete

To investigate the influences of three metallic polymeric materials in polyester and acrylic fresh polymer concretes (PCs), PC‐incorporated different levels of these materials have been investigated for their properties of fresh PC. The mix design was made and optimized for workability, strength, and economy, depending on the resin viscosity, the intended use, and the additional quantities of these polymeric materials. The properties investigated include workability, working time, and curing time of fresh PC. It is concluded that these polymeric materials offer the possibility of improving properties of polyester and acrylic fresh polymer concretes. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Symbol error probability of an OFDM receiver with pulse blanking based on the peak value threshold

Pulse blanking based on the peak value threshold is a widely used method to eliminate impulsive interference in the orthogonal frequency division multiplexing (OFDM) receiver. To assess the impact of pulse blanking on the link transmission reliability of the OFDM receiver, the analytical expression for the signal-to-noise ratio (SNR) of the OFDM receiver with pulse blanking based on the peak value threshold is derived in the frequency selective fading channel. According to this analysis, the calculation method for symbol error probability is given in this paper. Computer simulation indicates that theory accords with simulation and validates the accuracy of theoretical analysis.     

乳化沥青冷再生混合料和易性指标及影响因素

为了研究乳化沥青冷再生混合料和易性,采用自主研发的和易性测试设备,以扭矩值作为乳化沥青冷再生混合料和易性表征指标,研究了不同特性的乳化沥青、回收沥青路面材料( reclaimed asphalt pavement,RAP)掺量及拌和用水量对乳化沥青冷再生混合料和易性的影响规律,分析了乳化沥青冷再生混合料和易性影响因素的显著性,并通过反算水泥初凝时间以及旋转压实成型试件的体积参数是否在规范范围验证了测试方法及指标的合理性.结果表明：再生混合料和易性随着RAP掺量的增加而变差,合适的拌和用水量能显著改善再生混合料和易性;RAP掺量和拌和用水量对再生混合料和易性有显著影响,而乳化沥青特性的影响不明显;乳化沥青冷再生混合料在拌和后存在一个最佳压实时机,推荐扭矩阈值为20 N·m.     

Effects of parameters on rotational fine blanking of helical gear简

The application of fine blanking to the manufacturing of helical gears directly from a strip has been restricted due to the traditional linear cutting stroke of the punch and die. In this work, rotational fine blanking which combined the linear and rotational motion of punch and counterpunch was applied for the forming of helical gears. A three-dimensional （3D） rigid-plastic finite element model was developed on the DEFORM-3D platform. By finite element simulation and analysis, the influences of key parameters on the punch load and cut surface were investigated. It is shown that： 1） with increasing the counterforce or helical angle, the punch load and the depth of die roll increase; 2） with increasing blank holder force, the punch load increases while the depth of die roll decreases; 3） V-ring indenter facilitates an improvement in the quality. The results of this research reveal the deformation mechanism of rotational fine blanking of helical gears, and provide valuable guidelines for further experimental studies.     

�ȴ����25CrNiWV����ѧ���ܼ���֯��Ӱ��

 本文全面地研究了淬火温度和回火温度对25CrNiWV钢力学性能及金相组织的影响，确定了此钢种的最佳热处理工艺。     

聚氨酯橡胶冲裁模具的设计探讨

在冲裁薄料时，通常要用的是无间隙的冲模。以聚氨酯橡胶代替通常钢模中的凹模或凸模是比较有效的方法之一。在了解聚氨酯橡胶冲裁的过程和聚氨酯橡胶冲裁的工艺性的基础上，必须掌握聚氨酯橡胶；中裁模具主要零件的设计要领。     

00Cr22Ni5Mo3N双相不锈钢热加工性能的试验研究

采用热压缩和热拉伸试验方法,对00Cr22Ni5Mo3N双相不锈钢的高温变形抗力、高温塑性以及在高温变形时的奥氏体相的数量进行了研究。试验结果表明,00Cr22Ni5Mo3N双相不锈钢的高温变形抗力和高温塑性较0Cr18Ni10Ti奥氏体不锈钢低,在1100～1250℃变形时,钢中奥氏体相的数量可以控制在适合热加工的范围,使钢具有较好的热加工性能。