LBM investigation of a Cu-water nanofluid over various configurations of pipes in the mixed convection flow

Increasing the heat capacity of heat exchangers is a crucial need for modern devices. The thermal conductivity of the usual fluids and the Nusselt (Nu) number of flows containing such fluids are two bottlenecks in the way of increasing heat delivery in the heat exchangers. For this reason, nanofluids have been introduced. The effect of utilizing a Cu-water nanofluid as a coolant of two hot pipes in a square cavity is investigated numerically with a two-component lattice Boltzmann method. The volume fraction of nanoparticles is assumed to be constant (0.03) while the Richardson (Ri) number varies from 0.02 to 20. Results show that the effectiveness of nanoparticles is better observed in the natural convection mode. However, sedimentation is also very probable at high Ri numbers, which significantly reduces the effectiveness of the nanoparticles. Configurations which produce a natural convection stream similar to the forced convection one as well as the configurations with high spacing and hence, low heat stream interactions, are the best choices for a uniform heat rate from the pipes.     

Influence of CO2 inleakage on the slight-alkalization of generator internal cooling water

The slight-alkalization of generator internal cooling water (GICW) is widely used to inhibit the corrosion of hollow copper conductor and thereby ensure the safe operation of the generator. CO₂ inleakage is increasingly identified as a potential security risk for GICW system. In this paper, the influence of CO₂ inleakage on the slight-alkalization of GICW was theoretically discussed. Based on the equilibriums of the CO₂-NaOH-H₂O system, CO₂ inleakage saturation was derived to quantify the amount of the dissolved CO₂ in GICW. This parameter can be directly calculated with the measured conductivity and the [Na⁺] of GICW. The influence of CO₂ inleakage on the slight-alkalization conditioning of GICW and the measurement of its water quality parameters were then analyzed. The more severe the inleakage, the narrower the water quality operation ranges of GICW, resulting in the more difficult the slight-alkalization conditioning of GICW. The temperature calibrations of the conductivity and the pH value of GICW show non-linear correlations with the amount of CO₂ inleakage and the NaOH dosage. This study provides insights into the influence of CO₂ inleakage on the slight-alkalization of GICW, which can serve as the theoretical basis for the actual slight-alkalization when CO₂ inleakage occurs.     

Exergoeconomic performances of the desiccant-evaporative air-conditioning system at different regeneration and reference temperatures

This paper presented the exergoeconomic evaluation of the developed desiccant-evaporative air-conditioning system. The developed system was evaluated based on the steady-state conditions at different regeneration and reference temperatures. The exergoeconomic evaluation method was implemented to the system components and the whole system to evaluate the exergy efficiency, exergy destruction ratios, cost rates, relative cost differences and exergoeconomic factors. The regeneration and reference temperatures affected the exergy efficiencies, exergy destruction ratios, cost rates, relative cost differences and exergoeconomic factors. The desiccant wheel, heating coil and evaporative cooler had a high cost rate (investment cost, operation and maintenance cost, and exergy destruction cost). The exit air fan, outdoor air fan and evaporative cooler had a high relative cost difference. The exit air fan, outdoor air fan and secondary heat exchanger had a high exergoeconomic factor. Replacement of the desiccant wheel with a higher dehumidification performance could decrease the high cost rate. A higher efficiency evaporative cooler and heating coil were needed. Cheaper air fans (outdoor air fans and exit air fans) were needed.     

芳烃联合装置节能降耗方法探讨

结合芳烃联合装置的发展形势，通过对国内某4套典型芳烃联合装置运行能耗的构成进行分析，确定该类装置的主要能耗在于燃料、电和蒸汽的消耗。总结了目前国内外常用的芳烃联合装置节能降耗方法，利用实际经验和调研结果，从采用新型吸附剂、采用单台吸附塔新工艺、采用轻质解吸剂替代对二乙苯（PDEB）、优化吸附塔运行参数、加热炉节能优化和选用高效节能设备等角度探讨芳烃联合装置的节能降耗方法。芳烃联合装置节能降耗应该由设计单位和生产单位紧密结合，在设计阶段就应充分考虑生产过程面临的问题，充分优化工艺路线、方案和设备设计，尽可能降低装置的能耗。同样，装置运行过程中，生产部门应标准化、精细化管理，优化日常操作，从而进一步降低装置的操作能耗。     

丙烯腈装置回收塔内聚合物生成原因的分析

针对丙烯腈生产过程中回收塔内聚合物堵塞降液管造成回收塔运行周期短的问题,通过对丙烯腈回收塔内各组分分布的模拟计算,直观显示了回收塔内各组分的浓度分布,发现了回收塔的聚合段与丙烯醛的富集段相吻合的现象,初步得出了回收塔内局部聚合的原因;通过对塔内聚合物的特性分析和评判,进一步证实了“回收塔内局部聚合严重是由于在聚合段丙烯醛聚集引起”这一现象;根据模拟计算结果和实际运行经验,提出了预防聚合物堵塞降液管的措施,并进行了部分生产验证,为丙烯腈生产企业延长装置运行周期提供了理论指导。     

国产风机盘管空调系统常见问题分析

分析了国产风机盘管使用中常见的问题,指出机组因风量不足、冷量风量匹配不合理以及风机盘管某些设备故障,导致了风机盘管精度低、舒适性差、能耗高等一系列问题。指出应引起空调设计和运行维护人员的注意。     

防止干燥塔塔顶及锥节产生焦粉的方法

描述及分析了干燥塔在生产乳粉过程中出现的塔顶及锥节焦粉现象，并提出了改进方法。     

激光抛光技术的发展与展望

介绍激光抛光技术的发展历史,阐明激光抛光的应用现状及未来的发展前景,论述了激光抛光的工艺特点和作用机理,将激光抛光技术与其它抛光技术进行了全面的对比,指出激光抛光的优势及其存在的问题。     

回热损失对磁斯特林制冷循环制冷率的影响

从铁磁质的磁化强度一般表示式出发，探讨热阻和回热损失对磁斯特林制冷循环性能的影响，导出最大制冷率及其它性能参数。得到了结果适用于以顺磁质为工质的磁斯特林制冷循环。并指出在理想回热条件下的结论也适用于磁卡诺制冷循环。