A novel pre-dilution,swirling jet diffuser to enhance effluent mixing: Hydrodynamics and dilution performance

Diffusers are widely-used to quickly dilute effluents in receiving water bodies. This study proposed a novel diffuser that pre-mixes effluent with ambient water before discharging and that uses the swirling jet to further enhance near-field dilution. The nozzle of the diffuser was examined in two ambient flow conditions: co-flow and counter-flow that are commonly-met in the environment such as oceans due to tidal effect. Physical experiments were first conducted in co-flow on its dilution performance and hydrodynamics, using heated water as the effluent. A 3-D CFD model was developed and calibrated the co-flow scenarios, and then used to investigate the diffuser in counter-flow. The results showed that the nozzle can effectively reduce the maximum temperature rise of the effluent by about 50 % before discharging. The swirling jet from the outlet has a larger shear area, half-width and entrainment rate, enabling the effluent to be rapidly diluted to a minimum of around 10 times at x/D = 6 in co-flow, whereas the dilution for conventional nozzles is about 1 because of the potential core. The flow amplification ratio (α) decreases gradually with increasing velocity ratio in co-flow but increases with increasing velocity ratio in counter-flow. The counter-flow reduces the water drawn into the device; however, the pre-dilution effect at the outlet remains stable. The near-field dilution in counter-flow was significantly enhanced than that in co-flow. Environmental regulations at outfalls and mixing zones can be more easily met using this novel diffuser.     

以新发展理念引领高校专业基础课教学改革

以“创新、协调、绿色、开放、共享”为内核的新发展理念，是对马克思主义发展理念的继承和发扬，极具时代精神，富含问题意识，为高校思想政治教育发展、教育教学改革实践提供了强大的理论支撑。本文以“通信原理”为例，阐述了新发展理念在课程改革中的思路和方法，实现了思想政治教育与专业基础课程有机融合，为深化高校教学改革、创新人才培养模式提供了思路。     

Analysis and proposition of limiting current density measurement protocol

Limiting current density at different temperatures, backpressures, and balance gases can be used to separate molecular diffusion resistance, Knudsen diffusion resistance and local transport resistance of membrane electrode assembly (MEA). However, the measurement of limiting current density has no unified protocol. The diverse choices in the literature, either in the control of current or voltage or in the atmosphere like relative humidity and O₂ concentrations, make it difficult to compare the results and identify the true bottleneck hindering the mass transport. In this work, the current-voltage curves obtained by current scanning/stepping and voltage scanning/stepping methods under dilute O₂ of different concentrations and a wide range of relative humidity were measured and analyzed systematically. It is found that the voltage stepping method is superior to the other three ways of control for the reliable determination of the limiting current density. Aided with simultaneous electrochemical impedance spectroscopy measurement, the limiting current density can be determined with pinpoint accuracy. When the limiting current density is just used to qualitatively evaluate different MEA, the voltage scanning method can be used instead for its high time efficiency. The selection of the atmosphere also plays an important role in suppressing the distortion from excessive water and reducing the spurious contribution from proton conduction resistance. It is found that O₂ concentrations at 0.5 vol% and relative humidity at 90% can give the best estimation of O₂ transport resistance in membrane electrode assembly.     

Linear correlation between pH value of stimulated beef and electrical current intensity

The aim of the present study was to determine mathematical relationships between pH changes in beef 24 h post-slaughter and changes in the intensity of electrical current flowing through bull and heifer carcasses during high-voltage electrical stimulation. The electrical stimulation was applied 40 min postmortem for 120 s. The pH values of m. longissimus thoracis et lumborum were analyzed in the function of electrical current intensity changes and its change during electrical stimulation. Mathematical linear correlations of the y = ax ± b type were demonstrated between pH values at 2, 6, and 24 h postmortem and the initial (I_i) and ultimate (I_u) electrical current intensity values, the difference between them and the initial pH values determined before electrical stimulation. High multiple correlation coefficients (R² = 0.416, α ≤ 0.001) between I_u and pH values 24 h post-slaughter enabled concluding that there is a possibility to predict a pH value of stimulated carcass with high accuracy, and thus also beef quality, based merely on the ultimate electrical current intensity values.     

Passive micromixer with baffles distributed on both sides of microchannels based on the Koch fractal principle

Since the beginning of the 21st Century, the development of microfluidic chip technology has been very rapid and has attracted the attention of more and more scholars. As an important part of the microfluidic chip, the performance of the micromixer is critical. The fractal structure in the microchannels helps to improve the mixing performance of the micromixer and improve the mixing efficiency of the micromixer. The research results of other scholars are of great significance to the research of the present paper, which mainly studies the effect of changing the baffle state on the mixing efficiency of the micromixer based on the Koch fractal principle. Through simulation analysis, it was found that the mixing efficiency of the baffles distributed on both sides of the microchannel was higher than the mixing efficiency of the baffles distributed on the microchannel side. When the distance between adjacent baffles was divided into 0.15, 0.25 and 0.35 mm, simulated data suggested that the baffle distance of 0.15 mm was best. Increasing the number of baffles from six to eight groups increased the mixing path of the fluid in the microchannel and improved mixing efficiency. A comparison of mixing efficiencies of the 0°, 15° and 30° baffle angles revealed that very significant improvement in mixing efficiency was obtained at 30°. © 2019 Society of Chemical Industry     

浅谈不同给液方式在铜电解车间的应用

不同给液方式对铜电解过程中有重要的影响,不同的循环方式会影响槽内温度分布、电解液成分及阳极泥沉降等,因此,根据铜电解生产不同情况的需要,分析对比了多种给液方式在贵冶电解车间的应用,总结了这几种给液方式的优缺点和适用条件。     

“The innovation governance dilemma: Alternatives to the precautionary principle”

This article reviews the four innovation governance approaches (the precautionary principle, responsible innovation, permissionless innovation, and the innovation principle), including definitions, important attributes, and weaknesses found in each approach, and when utilizing an affinity diagram as a tool of analysis, identifies their distinctive characteristics and common relationships. A discussion section summarizes the paper’s findings and offers insights into where there is common relationships for further possible convergence between two innovation governance approaches – responsible innovation and permissionless innovation – that conceptually share substantially more in common than they contrast with each other. For addressing this challenge, the study recommends the following policy proposals: embrace artificial intelligence/machine learning/data analytics for risk management and regulatory adaptability; consider “soft law”as an option to public regulation; and substitute corporate citizenship for corporate social responsibility.     

Control theory for stochastic distributed parameter systems,an engineering perspective

The main purpose of this paper is to survey some recent progresses on control theory for stochastic distributed parameter systems, i.e., systems governed by stochastic differential equations in infinite dimensions, typically by stochastic partial differential equations. We will explain the new phenomenon and difficulties in the study of controllability and optimal control problems for one dimensional stochastic parabolic equations and stochastic hyperbolic equations. In particular, we shall see that both the formulation of corresponding stochastic control problems and the tools to solve them may differ considerably from their deterministic/finite-dimensional counterparts. More importantly, one has to develop new tools, say, the stochastic transposition method introduced in our previous works, to solve some problems in this field.