Plasma-assisted CO2 reforming of methane over Ni-based catalysts: Promoting role of Ag and Sn secondary metals

Carbon dioxide (CO₂) and methane (CH₄) are the primary greenhouse gases (GHGs) that drive global climate change. CO₂ reforming of CH₄ or dry reforming of CH₄ (DRM) is used for the simultaneous conversion of CO₂ and CH₄ into syngas and higher hydrocarbons. In this study, DRM was investigated using Ag–Ni/Al₂O₃ packing and Sn–Ni/Al₂O₃ packing in a parallel plate dielectric barrier discharge (DBD) reactor. The performance of the DBD reactor was significantly enhanced when applying Ag–Ni/Al₂O₃ and Sn–Ni/Al₂O₃ due to the relatively high electrical conductivity of Ag and Sn as well as their anti-coke performances. Using Ag–Ni/Al₂O₃ consisting of 1.5 wt% Ag and 5 wt% Ni/Al₂O₃ as the catalyst in the DBD reactor, 19% CH₄ conversion, 21% CO₂ conversion, 60% H₂ selectivity, 81% CO selectivity, energy efficiency of 7.9% and 0.74% (by mole) coke formation were achieved. In addition, using Sn–Ni/Al₂O₃, consisting of 0.5 wt% Sn and 5 wt% Ni/Al₂O₃, 15% CH₄ conversion, 19% CO₂ conversion, 64% H₂ selectivity, 70% CO selectivity, energy efficiency of 6.0%, and 2.1% (by mole) coke formation were achieved. Sn enhanced the reactant conversions and energy efficiency, and resulted in a reduction in coke formation; these results are comparable to that achieved when using the noble metal Ag. The decrease in the formation of coke could be correlated to the increase in the CO selectivity of the catalyst. Good dispersion of the secondary metals on Ni was found to be an important factor for the observed increases in the catalyst surface area and catalytic activities. Furthermore, the stability of the catalytic reactions was investigated for 1800 min over the 0.5 wt% Ag-5 wt% Ni/Al₂O₃ and 0.5 wt% Sn-5 wt% Ni/Al₂O₃ catalysts. The results showed an increase in the reactant conversions with an increase in the reaction time.     

Multi-discharge EDM coring of single crystal SiC ingot by electrostatic induction feeding method

A new technique of EDM coring of single crystal silicon carbide (SiC) ingot was proposed in this paper. Currently single crystal SiC devices are still of high cost due to the high cost of bulk crystal SiC material and the difficulty in the fabrication process of SiC. In the manufacturing process of SiC ingot/wafer, localized cracks or defects occasionally occur due to thermal or mechanical causes resulted from fabrication processes which may waste the whole piece of material. To save the part of ingot without defects and maximize the material utilization, the authors proposed EDM coring method to cut out a no defect ingot from a larger diameter ingot which has localized defects. A special experimental setup was developed for EDM coring of SiC ingot in this study and its feasibility and machining performance were investigated. Meanwhile, in order to improve the machining rate, a novel multi-discharge EDM coring method by electrostatic induction feeding was established, which can realize multiple discharges in single pulse duration. Experimental results make it clear that EDM coring of SiC ingot can be carried out stably using the developed experimental setup. Taking advantage of the newly developed multi-discharge EDM method, both the machining speed and surface integrity can be improved.     

基于深度信念网络的列车故障音频诊断方法

铁路在交通运输行业有着举足轻重的地位，一旦列车发生故障将会导致严重的生命财产损失。由于列车发生故障的概率相对较低，因此难以捕获列车的故障样本。针对上述问题，提出了一种无监督学习的列车故障识别方法，通过检测列车音频信号来识别列车故障。该方法基于深度信念网络(DBN)，利用小波包分解提取检测信号的特征向量并将其作为DBN的输入，待网络充分训练后，由训练好的DBN识别当前列车的运行状况。现场监测实验结果表明，该方法能够在无监督的条件下有效识别列车故障，保障了列车的运行安全。     

基于深度学习的秀丽隐杆线虫显微图像分割方法

利用计算机实现自动、准确的秀丽隐杆线虫(C.elegans)的各项形态学参数分析,至关重要的是从显微图像上分割出线虫体态,但由于显微镜下的图像噪声较多,线虫边缘像素与周围环境相似,而且线虫的体态具有鞭毛和其他附着物需要分离,多方面因素导致设计一个鲁棒性的C.elegans分割算法仍然面临着挑战。针对这些问题,提出了一种基于深度学习的线虫分割方法,通过训练掩模区域卷积神经网络(Mask R-CNN)学习线虫形态特征实现自动分割。首先,通过改进多级特征池化将高级语义特征与低级边缘特征融合,结合大幅度软最大损失(LMSL)损失算法改进损失计算;然后,改进非极大值抑制;最后,引入全连接融合分支等方法对分割结果进行进一步优化。实验结果表明,相比原始的Mask R-CNN,该方法平均精确率(AP)提升了4.3个百分点,平均交并比(mIOU)提升了4个百分点。表明所提出的深度学习分割方法能够有效提高分割准确率,在显微图像中更加精确地分割出线虫体。     

东兴铝业嘉峪关分公司铝灰渣循环利用研究

铝灰渣是铝熔铸过程中产生的废弃物。本文主要介绍了酒钢东兴铝业嘉峪关分公司铝灰渣的产生量、排放、利用情况、化学成分及表面特征,并简要介绍了铝灰渣、铝灰的循环利用途径。     

Modeling the effect of deep traps on the capacitance–voltage characteristics of p-type Si-doped GaAs Schottky diodes grown on high index GaAs substrates

Numerical simulation, using SILVACO-TCAD, is carried out to explain experimentally observed effects of different types of deep levels on the capacitance–voltage characteristics of p-type Si-doped GaAs Schottky diodes grown on high index GaAs substrates. Two diodes were grown on (311)A and (211)A oriented GaAs substrates using Molecular Beam Epitaxy (MBE). Although, deep levels were observed in both structures, the measured capacitance–voltage characteristics show a negative differential capacitance (NDC) for the (311)A diodes, while the (211)A devices display a usual behaviour. The NDC is related to the nature and spatial distribution of the deep levels, which are characterized by the Deep Level Transient Spectroscopy (DLTS) technique. In the (311)A structure only majority deep levels (hole traps) were observed while both majority and minority deep levels were present in the (211)A diodes. The simulation, which calculates the capacitance–voltage characteristics in the absence and presence of different types of deep levels, agrees well with the experimentally observed behaviour.     

改进HSR-FCN的服装图像识别分类算法研究

目前网络上的服装图像数量增长迅猛，对于大量服装图像实现智能分类的需求日益增加。将基于区域的全卷积网络（Region-Based Fully Convolutional Networks，R-FCN）引入到服装图像识别中，针对服装图像分类中网络训练时间长、形变服装图像识别率低的问题，提出一种新颖的改进框架HSR-FCN。新框架将R-FCN中的区域建议网络和HyperNet网络相融合，改变图片特征学习方式，使得HSR-FCN可以在更短的训练时间内达到更高的准确率。在模型中引入了空间转换网络，对输入服装图像和特征图进行了空间变换及对齐，加强了对多角度服装和形变服装的特征学习。实验结果表明，改进后的HSR-FCN模型有效地加强了对形变服装图像的学习，且在训练时间更短的情况下，比原来的网络模型R-FCN平均准确率提高了大约3个百分点，达到96.69%。     

Enhance cycling performance of LiMn2O4 cathode by Sr2+ and Cr3+ doping

Spinel LiSr_0·1Cr_0·1Mn_1·8O₄ was synthesised by high temperature solid state method in order to enhance the electrochemical performance. The LiSr_0·1Cr_0·1Mn_1·8O₄ (LSCMO) materials were characterised by X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical tests. The XRD and SEM studies confirm that LSCMO had spinel crystal structure with a space group of Fd3m, and the particle of LSCMO shows irregular shape. The cyclic voltammetry data illustrated that the heavy current charge–discharge performance of LMO was improved by Sr²⁺ and Cr³⁺ doping. The galvanostatic charge–discharge of LSCMO cathode materials was measured at 1, 5, 10 and 20 C. The results indicated that LSCMO improved the capacity retention.     

仪器仪表产品脉冲耐压试验要求和保护器件的选择

仪器仪表产品的脉冲耐压试验是产品型式试验、例行试验中的基本内容。通过对GB4793.1标准的整理,归纳了仪器仪表产品的脉冲耐压试验要求。通过对试验方法和设备特性的梳理,总结了特性参数,并介绍了应对脉冲耐压试验可采取的保护器件的类别及选用方法。