A New Comb Circular Polarizer Suitable for Millimeter‐Band Application

This letter presents a new polarizer which has a simple comb structure inside a circular waveguide. The electrical performance of the proposed comb polarizer is optimized by a circular waveguide radius and by the physical parameters of the comb plates. This polarizer is suitable for providing good performance in millimeter‐band application because of its simple structure and low fabrication cost. In our experiments the dual‐band comb polarizer designed in band 1(K) and band 2(Ka) showed good electrical performance without any tuning elements.     

A semi-analytic boundary element method for parabolic problems

A new semi-analytic solution method is proposed for solving linear parabolic problems using the boundary element method. This method constructs a solution as an eigenfunction expansion using separation of variables. The eigenfunctions are determined using the dual reciprocity boundary element method. This separation of variables-dual reciprocity method (SOV-DRM) allows a solution to be determined without requiring either time-stepping or domain discretisation. The accuracy and computational efficiency of the SOV-DRM is found to improve as time increases. These properties make the SOV-DRM an attractive technique for solving parabolic problems.     

Boundary knot method for 2D and 3D Helmholtz and convection–diffusion problems under complicated geometry

The boundary knot method (BKM) of very recent origin is an inherently meshless, integration‐free, boundary‐type, radial basis function collocation technique for the numerical discretization of general partial differential equation systems. Unlike the method of fundamental solutions, the use of non‐singular general solution in the BKM avoids the unnecessary requirement of constructing a controversial artificial boundary outside the physical domain. The purpose of this paper is to extend the BKM to solve 2D Helmholtz and convection–diffusion problems under rather complicated irregular geometry. The method is also first applied to 3D problems. Numerical experiments validate that the BKM can produce highly accurate solutions using a relatively small number of knots. For inhomogeneous cases, some inner knots are found necessary to guarantee accuracy and stability. The stability and convergence of the BKM are numerically illustrated and the completeness issue is also discussed. Copyright © 2003 John Wiley & Sons, Ltd.     

DLL23XA双侧向测井仪的研制

以往双侧向测井仪动态范围小，测量精度低，为此开发了DLL23XA双侧向测井仪。该仪器主要单元采用厚膜电路，稳定性、一致性好；深、浅屏流源采用可变功率控制，提高了仪器的动态范围。仪器采用3506P例进行数据传输，可方便地配接各种地面系统。     

Geometric features of the flame propagation process for an SI engine having dual‐ignition system

Flame front surface area and enflamed volume (the volume enclosed with flame front) is theoretically analysed for a spark‐ignition engine, having cylindrical disc‐shaped combustion chamber with two spark plugs located axisymmetrically on cylinder head, between cylinder axis and cylinder wall. Spherical flame front assumption is used. A computer code is developed based on purely geometric consideration of the flame development process in combustion chamber, and is used to investigate the effects of variations of spark plugs' locations on geometric features of the flame front. A comparison has also been made with a spark‐ignition engine having one spark plug at the same location. Copyright © 2002 John Wiley & Sons, Ltd.     

等距码的对偶距离分布及其性质

本文主要讨论了等距码的对偶距离分布及其性质，然后利用这些性质将［１］中的某些结果推广到ｑ元等距码情形，并得到了其对偶距离分布的递推关系式，最后，本文给出了ｑ元等距码的码字数目的一个上界。     

Construction of a control system for disturbance rejection using a dual observer

A well‐known control system which can reduce the adverse effects of disturbances is a disturbance observer. However, in many cases of mechanical systems, system disturbances which do not satisfy the matching condition may be imposed. Therefore, it may be difficult to reduce the adverse effects of the disturbances by the traditional disturbance observer. In this paper, a method of control system synthesis for disturbance rejection using a dual observer is proposed. This method is based on the zeroing induced by the disturbance localization problem. This problem may be solved by dividing the state space into observable subspace and unobservable subspace. As compared with an H_∞ controller based on perfect observation, the usefulness of the proposed control system for disturbance rejection is demonstrated by numerical simulations for a two‐mass spring system. © 2002 Scripta Technica, Electr Eng Jpn, 138(4): 50–60, 2002; DOI 10.1002/eej.1138     

双波长Nd：YAG脉冲激光器的实验研究

根据多波长同时振荡条件，我们建立了大能量１０６４ｎｍ和１３１８ｎｍ同时运转的双波长脉冲Ｎｄ：ＹＡＧ激光器。得到了１０６４ｎｍ和１３１８ｎｍ的激光输出能量分别为０．５９４Ｊ和０．８６１Ｊ，效率分别为０．３１％和０．４５％。实验结果说明了该双波长激光器有较好的时间和空间重选性。     

一种高性能图形板的设计与实现

介绍了一种采用高性能嵌入式图形处理器、大容量双端口视频存储器、高性能查色表以及超大规模可编程逻辑器件设计的图形显示控制板的基本组成和工作原理。     

The application of microencapsulated phase‐change materials to nylon fabric using direct dual coating method

The fabrication of functional textiles able to provide thermal regulation and comfort for the body has attracted increasing interest in recent years. This research investigated fabric coatings containing energy absorbing, temperature stabilizing, phase‐change material microcapsules (PCMMcs), and their methods of application. Specifically, a coated fabric was directly prepared by a dual‐type coating method, in which the PCMMcs were dispersed in a polyurethane coating solution with no binder. The thermal performances of the dual‐coated samples were evaluated by differential scanning calorimetry, and their physical characteristics were examined by scanning electron microscopy, thermal vision camera, porosity, water vapor transmission rate (WVTR), and water entry pressure (WEP) analyses. Furthermore, the microclimate characteristics of the thermally enhanced fabrics were investigated under experimental conditions using a human‐clothing‐environment (HCE) simulator system. The study results confirmed the superior performance of the dual‐coated fabrics in terms of thermal regulation and body comfort, compared with those coated by the dry or wet coating method, because of the improved WEP, WVTR, and thermal performance. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008