Hydrogen production by supercritical water gasification of lignin over CuO–ZnO catalyst synthesized with different methods

In this study, lignin was gasified in supercritical water with catalysis of CuO–ZnO synthesized by deposition precipitation, co-precipitation and sol-gel methods. Sol-gel synthesized CuO–ZnO showed the highest catalytic performance, and the gasification efficiency was increased by 37.92% with it. The XRD, SEM-EDS and N₂ adsorption/desorption analysis showed that the priority of the sol-gel catalyst was the smallest crystallite size, largest specific surface area and high dispersion. For sol-gel synthesized CuO–ZnO, the increase of CuO/ZnO ratio improved the gasification efficiency but reduced H₂ selectivity. And the catalytic activity was reduced with the calcination temperature above 600 °C due to enlarged crystallites and reduced pores. During sol-gel preparation, both the addition of ethanol and PEG in the solvent reduced the agglomeration and improved the catalytic activity. With CuO–ZnO prepared with 1 g PEG + water as the solvent, the highest H₂ yield of 6.86 mol/kg was obtained, which was over 1.5 times of that without catalyst.     

Hydraulic reactivity and cement formation of baghdadite

In this study, the hydraulic reactivity and cement formation of baghdadite (Ca₃ZrSi₂O₉) was investigated. The material was synthesized by sintering a mixture of CaCO₃, SiO₂, and ZrO₂ and then mechanically activated using a planetary mill. This leads to a decrease in particle and crystallite size and a partial amorphization of baghdadite as shown by X-ray powder diffraction (XRD) and laser diffraction measurements. Baghdadite cements were formed by the addition of water at a powder to liquid ratio of 2.0 g/ml. Maximum compressive strengths were found to be ~2 MPa after 3-day setting for a 24-h ground material. Inductively coupled plasma mass spectrometry (ICP-MS) measurements showed an incongruent dissolution profile of set cements with a preferred dissolution of calcium and only marginal release of zirconium ions. Cement formation occurs under alkaline conditions, whereas the unground raw powder leads to a pH of 11.9 during setting, while prolonged grinding increased pH values to approximately 12.3.     

Energy conversion performances during biomass air gasification process under microwave irradiation

Biomass gasification technology under microwave irradiation is a new and novel method, and the energy conversion performances during the process play a guiding role in improving the energy conversion efficiencies and developing the gasification simulation models. In order to improve the energy utilization efficiency of microwave biomass gasification system, this study investigated and presented the energy conversion performances during biomass gasification process under microwave irradiation, and these were materialized through detailing (a) the energy conversion performance in the microwave heating stage, and (b) the energy conversion performance in the microwave assisted biomass gasification stage. Different forms of energies in the biomass microwave gasification process were calculated by the method given in this study based on the experimental data. The results showed that the useful energy (energy in silicon carbide (SiC), 18.73 kJ) accounted for 31.22% of the total energy input (electrical energy, 60.00 kJ) in the heating stage, and the useful energy (energy in the products, 758.55 kJ) accounted for 63.41% of the total energy input (electrical and biomass energy, 1196.28 kJ) in the gasification stage. During the whole biomass gasification process under microwave irradiation, the useful energy output (energy in the products, 758.55 kJ) accounted for 60.38% of the total energy input (electrical and biomass energy, 1256.28 kJ), and the energy in the gas (523.40 kJ) product played a dominate role in product energy (758.55 kJ). The energy loss mainly included the heat loss in the gas flow (89.20 kJ), magnetron loss (191.80 kJ) and microwave dissipation loss (198.00 kJ), which accounted for 7.10%, 15.27% and 15.76% of the total energy, respectively. The contents detailed in this study not only presented the energy conversion performances during microwave assisted gasification process but also supplied important data for developing gasification simulation models.     

Combination of nuclear magnetic resonance spectroscopy and nonlinear methods to analyze the copolymerization of phosphonic acid derivatives

We demonstrate in this study that the combination of modern inline monitoring methods [here: inline nuclear magnetic resonance (NMR)] with simulations gains more exact and profound kinetic results than previously used methods like linearization without that combination. The ¹H-NMR spectroscopic data (more than 100 data points) are used to construct the copolymerization diagram. The reactivity ratios are obtained applying the van Herks nonlinear least square method. The examination of the radical copolymerization of 2-hydroxyethyl methacrylate (HEMA) with (2-{[2-(ethoxycarbonyl)prop-2-en-1-yl]oxy}ethyl) phosphonic acid (ECPPA) as important adhesive monomer used in dentistry yields reactivity ratios of r_HEMA = 1.83; r_ECPPA = 0.42. The copolymerization diagram reflects nonideal, non-azeotropic copolymerization. The sequence distribution of the obtained by Monte Carlo simulation indicates the generation of statistical copolymers. As an important finding, it is demonstrated that the repeating units responsible for etching and adhesion are arranged over the whole polymer chain, which is necessary to achieve proper functionality. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48256.     

A novel utilized method of tar derived from biomass gasification for fabricating binder-free all-solid-state hybrid supercapacitors

As an industrial pollutant, tar derived from biomass gasification is used as the precursor for fabricating a novel carbon-metal hydroxides composite electrode. A slurry (the mixture of tar, KOH and melamine) is daubed uniformly onto the nickel foam, which is directly carbonized to form NPC@LDH electrode material. This electrode is further coated with NiCo-LDH nanosheets using an electrodeposition method to form NF@NPC@LDH. The newly made NF@NPC@LDH electrode exhibits a high specific capacity of 9.6 F cm⁻² at a current density of 2 mA cm⁻² and good rate performance (55.3% retention). Furthermore, a hybrid NF@NPC@LDH//NF@PC all-solid-state supercapacitor is fabricated, and the device exhibits high energy density of 1.28 mWh cm⁻³ at a power density of 8.04 mW cm⁻³, low resistance and good cycling stability.     

Effects of unequal reactivity of functional groups on gelation phenomena in polyurethane systems

A model to describe the effect of unequal reactivity on curing of a diisocyanate with water, polyol and a diol was developed. The model predicts whether a given initial composition would gel or not and the fractional conversions of functional groups at the gel point. It has been shown that the relative speeds of reaction of water and hydroxyl groups can be used to classify water's behaviour as that of a (i) nonreactive diluent (ii) monofunctional blocking agent and (iii) chain extender capable of connecting branch points.     

壳牌煤气化工艺在荷兰德姆科列克IGCC工厂的应用

介绍采用壳牌煤气化工艺的荷兰德姆科列克250MW整体煤气化烧气－－蒸汽联合循环发电厂的建厂过程及运行经验。阐述了IGCC能量平衡原理、SCGP系统流程和运行操作指标，对壳牌煤气化装置的优良性能和发展前景进行了总结和展望。     

Electro-copolymerisation of indene and styrene

Electroinitiated cationic copolymerisation of indene and styrene was investigated by constant potential electrolysis. Effects of copolymerisation potential and temperature on the copolymer composition and the reactivity ratios are discussed. The reactivity ratios of the monomers were calculated according to the integrated Lewis-Mayo equation.